Abstract
The key challenge for high-power delivery through optical fibers is overcoming nonlinear optical effects. To keep a smooth output beam, most techniques for mitigating optical nonlinearities are restricted to single-mode fibers. Moving out of the single-mode paradigm, we show experimentally that wavefront-shaping of coherent input light to a highly multimode fiber can increase the power threshold for stimulated Brillouin scattering (SBS) by an order of magnitude, whilst simultaneously controlling the output beam profile. The SBS suppression results from an effective broadening of the Brillouin spectrum under multimode excitation, without broadening of transmitted light. Strongest suppression is achieved with selective mode excitation that gives the broadest Brillouin spectrum. Our method is efficient, robust, and applicable to continuous waves and pulses. This work points toward a promising route for mitigating detrimental nonlinear effects in optical fibers, enabling further power scaling of high-power fiber systems for applications to directed energy, remote sensing, and gravitational-wave detection.
Similar content being viewed by others
Introduction
Optical fibers facilitate nonlinear light–matter interactions through strong optical confinement and long interaction lengths1,2,3,4,5,6,7. One prominent nonlinear process is stimulated Brillouin scattering (SBS)—light scattering mediated by acoustic phonons1,4,6. SBS has a wide range of applications from optical phase conjugation, beam combining and cleanup, to coherent light and acoustic-wave generation, temperature and pressure sensing, and light delay and storage in fibers and integrated waveguides8,9,10,11,12,13,14,15,16,17,18,19,20. However, SBS remains a roadblock to other applications, and many efforts have been devoted to suppressing it. SBS is a major impediment to high-power delivery of narrowband light through optical fibers and fiber amplifiers, as it converts forward-propagating light to a backward-propagating Stokes wave4,21,22,23,24,25. Not only do the forward signals sustain significant loss but also the backward Stokes wave can damage the upstream lasers. SBS grows from noise and limits the maximum power transmissible through the fiber.
A straightforward way of mitigating SBS is enlarging the fiber core to lower the optical intensity. However, a large core usually supports multiple guided modes, and their interference creates random speckles. Such speckled fields are often assumed to prevent generation of a clean beam suitable for applications of power delivery and coherent beam combining. Thus most techniques developed to suppress SBS are based on single-mode fibers that output a diffraction-limited beam. For example, large-mode-area microstructured fibers support single-mode operation26, but they cannot be coiled and suffer inefficient heat dissipation27,28. An alternative approach is tailoring the fiber geometry to modify the acoustic modes and reduce their coupling with light29,30,31,32,33. Additionally, fibers with intrinsically low nonlinearity have been fabricated34. Mass production of such specialty fibers remains a technical challenge. To use standard single-mode fibers, spectral broadening of the input light is widely employed to broaden the Brillouin scattering spectrum and lower the SBS growth rate35. However, linewidth broadening is detrimental to practical applications such as spectral and coherent beam combining, dense wavelength-division multiplexing, and gravitational-wave detection36,37. Another way of broadening the SBS spectrum is introducing large temperature or strain gradients along the fiber38,39, which is hard to implement practically and shortens the fiber lifespan.
Here we propose and demonstrate an efficient method of suppressing SBS in standard multimode fibers while maintaining narrow linewidth and high output-beam quality, via wavefront shaping. Recent advances in wavefront-shaping techniques have enabled controlling nonlinear optical processes in multimode fibers7,40,41,42,43, but suppression of SBS has not been studied previously. Our approach is illustrated in Fig. 1: Shaping the input wavefront of a narrowband signal to excite many fiber modes allows simultaneously to increase the SBS threshold and focus the transmitted light to a diffraction-limited spot, which can be collimated by a lens. The SBS suppression is not simply due to reduced intensity when the core diameter is increased. The multimode excitation broadens the SBS gain spectrum and lowers the peak gain for the same intensity spread in the core. One advantage over prior schemes is that our method does not cause spectral broadening of the transmitted light (see Supplementary Information, sec. 1.5), facilitating narrowband applications. We maximize the SBS threshold by optimizing the excited modal content in a multimode fiber (MMF). The selective mode excitation efficiently broadens the SBS spectrum by taking advantage of variations in Brillouin scattering strength among different fiber-mode pairs. Combining the effects of intensity reduction and coherent multimode excitation, the SBS threshold in a step-index MMF with 20-μm core is one order of magnitude higher than that of a conventional single-mode fiber of the same length1,4 (see section “Discussion”). Our experimental results, performed with both continuous-wave (CW) excitation at wavelength λ = 1064 nm and 186-ns pulses at 1550 nm, confirm that our method is effective, robust, and generally applicable to different settings. It will enable power scaling of light delivery and amplification for various applications, e.g., directed energy and long-range remote sensing37,44,45,46.
Results
Suppression of stimulated Brillouin scattering by multimode excitation
We first demonstrate SBS mitigation by coherent multimode excitation. To this end, we vary the number of excited modes and measure the SBS threshold. The input signal (serving as the pump for SBS) is a linearly polarized continuous wave from a narrowband (15-kHz) fiber laser at λ = 1064 nm. It is launched into a 50-m-long, Ge-doped, step-index MMF with ~20-μm core diameter and 0.3 numerical aperture (NA), supporting ~80 modes per polarization. The transmitted light from the distal fiber end is split to simultaneously measure the output power and near-/far-field intensity patterns. We also monitor the input and backscattered light at the proximal fiber end (Supplementary Information, sec. 1).
We start with exciting only the fundamental mode (FM) in the MMF by focusing the incident light to the proximal fiber facet using a lens of NA matching that of the FM [Fig. 2a–c]. The transmitted beam produces a single spot at the center of the far field. We gradually increase the input power, and the output power first increases linearly but then levels off [Fig. 2j]. Meanwhile, the reflected power grows rapidly, indicating the onset of backward SBS. The transmitted power at this threshold is 1.8 W, which matches the value estimated with the well-known Smith formula: \(21\,{({g}_{{{{{{{{\rm{B}}}}}}}}}L)}^{-1}\), where gB ~ 0.2 W−1 m−1 is the Brillouin scattering strength and L is the fiber length1,47. Above the threshold, both transmitted signal and reflected Stokes exhibit temporal fluctuations under CW excitation [Fig. S1b, c]. The SBS threshold power with FM-only excitation in our MMF is ~4 times of that in a conventional single-mode fiber (~8-μm core and ~0.1 NA), as the SBS threshold scales with the effective FM area4).
Next, we excite multiple modes in the MMF by switching to a lens of larger NA (close to the core NA) [Fig. 2d–f]. The input beam is focused onto a small spot at the proximal fiber facet. When the focal spot is at the core center, predominantly the FM and several purely radial modes are excited. The output far-field pattern displays concentric rings. Due to modal interference, the near-field pattern is smaller than that of FM-only excitation. Nevertheless, the SBS threshold power rises to 2.6 W, indicating that the SBS suppression is not caused by transverse energy spreading that lowers the intensity. Instead, it is due to spectral broadening and peak reduction of the SBS gain by multimode excitation (see section “Broadening of Brillouin scattering spectrum”).
To excite even more modes, we move the focal spot away from the core center [Fig. 2g–i]. Additional higher-order modes (HOM) with nonzero azimuthal index are excited in addition to the FM and radial HOMs. Consequently, the output beam is highly speckled. The SBS threshold increases with the distance din of the focal spot from the fiber core center [Fig. 3a], as more modes are excited. Near the core edge, the threshold reaches 5.4 W, ~3 times the FM-only threshold.
Broadening of Brillouin scattering spectrum
To understand the mechanism of SBS suppression with multimode excitation, we have developed a multimode SBS theory (detailed derivation in ref. 48). Consider Brillouin scattering of a forward-propagating photon (signal) in fiber mode l to a backward photon (Stokes) in mode m via emission of a forward acoustic phonon at frequency Ω. The Stokes photon has a frequency shift of Ω from the signal photon. The scattering strength \({g}_{{{{{{{{\rm{B}}}}}}}}}^{(m,l)}(\Omega )\) is determined by the spatial overlap of optical modes m and l with acoustic modes in the fiber48. We order the modes by their propagation constants from high to low.
We refer m = l to intramodal scattering and m ≠ l to intermodal scattering. Figure 3b shows that if the signal is in the FM (l = 1), the Brillouin scattering is the strongest for Stokes in the FM (m = 1), with scattering strength \({g}_{{{{{{{{\rm{B}}}}}}}}}^{(1,1)}(\Omega )\) peaked at Stokes frequency Ω equal to the eigenfrequency of the lowest-order acoustic mode. The intramodal scattering for a HOM (e.g., HE24) has a lower peak at the same Ω, due to smaller overlap with the lowest-order acoustic mode, and an additional peak at higher Ω corresponding to a higher-order acoustic mode. Intermodal scattering is generically weaker than intramodal scattering, due to smaller acousto-optic overlap for non-identical signal and Stokes mode profiles. The intermodal peak is not only lower, but also spectrally shifted from the intramodal peak, because the acoustic mode having the largest spatial overlap with the signal and Stokes modes is a higher-order mode with higher eigenfrequency.
Seeded by spontaneous Brillouin scattering from mode l to m, the Stokes power \({P}_{m}^{{{{{{{{\rm{s}}}}}}}}}\) grows exponentially via SBS while propagating backward in the fiber. The growth rate is given by the product of the scattering strength \({g}_{{{{{{{{\rm{B}}}}}}}}}^{(m,l)}(\Omega )\) and the signal power Pl48. The SBS threshold is defined by the transmitted signal power at which a significant fraction of the input power is lost to backward Stokes. Below the SBS threshold, however, the Stokes power is at most a few percent of the input power, thus the depletion of signal power by SBS is negligible. If the signal power is distributed among M modes, the growth rate for \({P}_{m}^{{{{{{{{\rm{s}}}}}}}}}\) is given by the weighted sum \({G}_{{{{{{{{\rm{B}}}}}}}}}^{(m)}(\Omega )=\mathop{\sum }\nolimits_{l=1}^{M}{g}_{{{{{{{{\rm{B}}}}}}}}}^{(m,l)}(\Omega ){P}_{l}\), defined as the Brillouin gain coefficient. The Stokes power, which is maximal at the fiber proximal end (z = 0), is:
where \({P}_{m}^{{{{{{{{\rm{s}}}}}}}}}(\Omega,\, z=L)\) is the seed from spontaneous Brillouin scattering at the fiber distal end4. The exponential growth rate of Stokes power is dictated by the peak value of \({G}_{{{{{{{{\rm{B}}}}}}}}}^{(m)}(\Omega )\), which depends both on the strength of the coupling and on the signal power allocated to each mode.
Let us analyze \({G}_{{{{{{{{\rm{B}}}}}}}}}^{(m)}(\Omega )\) for a few cases. When only the FM is excited by the signal in a MMF, the Brillouin gain is strongest for the Stokes in the FM: \({G}_{{{{{{{{\rm{B}}}}}}}}}^{(1)}(\Omega )={g}_{{{{{{{{\rm{B}}}}}}}}}^{(1,1)}(\Omega ){P}_{1}\). Since \({g}_{{{{{{{{\rm{B}}}}}}}}}^{(1,1)}(\Omega )\) has the highest peak among all \({g}_{{{{{{{{\rm{B}}}}}}}}}^{(m,l)}(\Omega )\) [Fig. 3b], it results in the lowest SBS threshold. Instead, if a single HOM (l ≠ 1) is excited, Stokes growth in that HOM (m = l) is strongest. Since intramodal scattering for an HOM is weaker than that for the FM, the SBS threshold is slightly higher. When the FM and a HOM are equally excited, the Brillouin gain for the FM \({G}_{{{{{{{{\rm{B}}}}}}}}}^{(1)}=\big[{g}_{{{{{{{{\rm{B}}}}}}}}}^{(1,1)}+{g}_{{{{{{{{\rm{B}}}}}}}}}^{(1,2)}\big]/2\) is larger than that for the HOM. Both values are smaller than the Brillouin gain for single-mode (FM-only or HOM-only) excitation, because intermodal scattering is significantly weaker than intramodal scattering due to mismatch in spatial and polarization overlap when two modes are different [Fig. 3b]. This result generalizes to many-mode excitation, where distributing the power into many modes greatly lowers the maximum Brillouin gain. The Brillouin gain \({G}_{{{{{{{{\rm{B}}}}}}}}}^{(m)}(\Omega )\) for multimode excitation is a power-weighted sum of intramodal and intermodal scattering. The gain spectrum is broadened for Stokes in individual mode m due to frequency-offset peaks of \({g}_{{{{{{{{\rm{B}}}}}}}}}^{(m,l)}\) among different mode pairs (m,l). Consequently, the peak growth rate of Stokes power is greatly reduced, leading to significant threshold enhancement over single-mode excitation.
To compare with experimental data [Fig. 3a], we calculate the modes excited by a signal focused on the proximal facet and obtain the Brillouin gain spectrum and the SBS threshold (Supplementary Information, sec. 2.1). A tight focus on the core center excites multiple modes, leading to a broader Brillouin gain spectrum than FM-only excitation and thus a lower peak [Fig. 3c]. Shifting the focus transversely to excite even more modes, the spectrum is further broadened with a much lower peak. The SBS threshold, predicted by our theory, increases monotonically with din, and agrees well with the experimental data [Fig. 3a]. To obtain such agreement, we experimentally characterize the mode-dependent loss, linear mode coupling, and polarization mixing of our MMF, and include these effects in the SBS theory (Supplementary Information, sec. 2.2). Slope variation in the data is reproduced and explained by the theory (Supplementary Information, sec. 2.1).
Robustness of suppression scheme
The experiment with input focusing validates our multimode scheme for SBS suppression, but is restricted to a focused Gaussian input. To examine how robust this method is, we conduct a statistical study of the SBS threshold for arbitrary input wavefronts. We imprint random phase patterns on the signal beam (CW at 1064 nm) with a spatial light modulator (SLM) [Fig. 4a]. Strikingly, for all random input wavefronts, the threshold enhancement over FM-only excitation is consistently >2 [Fig. 4b]. The histogram shows a mean enhancement of ~ 2.7 and a small standard deviation σ ≈ 0.14. The prediction from simulations based on our theory is consistent with the experimental data [Fig. 4b]. It confirms that the random input wavefront distributes the signal power rather uniformly among all fiber modes [upper panel, Fig. 4c]. The calculated Brillouin gain spectrum [inset, Fig. 4d] has a full-width-at-half-maximum (FWHM) of 72 MHz, wider than the FM-only FWHM of 40 MHz. Consequently, the gain peak is notably lower, leading to threshold increase.
Figure 4d reveals the correlation between the threshold enhancement and Brillouin gain spectrum width. Different random input wavefronts cause variations in the excited mode content, leading to slightly different widths of the Brillouin gain spectrum. Larger widths correspond to higher SBS thresholds, with a Pearson correlation coefficient of 0.78.
To demonstrate the generality of our approach for SBS suppression, we switch from CW to pulsed (186-ns) signal at a different wavelength (1550 nm) and repeat the above experiments on the same type of MMF [Fig. 4e]. Under random multimode excitation, the mean SBS threshold enhancement is 2.1, slightly lower than that at 1064 nm. This is expected at a longer wavelength, where the fiber supports fewer optical modes (~37 per polarization).
Optimization of multimode excitation
The input-focusing data and the spread of SBS thresholds under random input wavefronts suggest that some multimode combinations are more efficient than others in mitigating SBS. These results prompt us to optimize the input wavefront for further enhancement of the SBS threshold. We sequentially optimize the phases of 8 × 8 SLM macropixels, to increase the transmitted signal power and/or decrease the backscattered Stokes power (Supplementary Information, sec. 1.4). The threshold is increased to 3.6 times the FM-only threshold, higher than that with off-axis input-focusing, and ~7σ higher than the mean enhancement with random wavefronts [Fig. 4b]. To better understand the mechanism underlying the threshold enhancement, we combine our theory with a numerical simulation of the SLM phase optimization to maximize the SBS threshold. The threshold enhancement reaches 3.5, closely matching the experimental result (Supplementary Information, sec. 2.3).
As shown in Fig. 4c, the optimized mode content (from simulation) is not uniform; instead the power is concentrated in several groups that are widely spaced in propagation constant. Such selective mode excitation broadens the Brillouin gain spectrum more effectively than uniform mode excitation, and the FWHM reaches 85 MHz [inset, Fig. 4d]. Starting from different input wavefronts, the optimization procedure takes different routes, and the final SBS thresholds vary slightly [Fig. 4d]. Although the optimized mode contents differ from one another [see Fig. S11b], they all consist of well-separated groups for maximal broadening of the Brillouin gain spectrum.
Control of output beam profile
Finally, we show that wavefront shaping of a coherent signal not only can mitigate the SBS in a MMF, but also can shape the transmitted beam profile. Since our theory finds that the SBS suppression depends only on how the signal power is distributed among modes [Eq. (1)], the phase of the input field to individual modes can be adjusted to control the modal interference at the fiber output. Below we present an example of focusing the output light to a diffraction-limited spot. Perfect focusing requires full control of the input field amplitude and phase49, whereas we have phase-only control with an SLM. Nevertheless, we find that this incomplete control can still direct most transmitted power to a designated location and simultaneously increase the SBS threshold.
As illustrated in Fig. 5a, a linearly-polarized Gaussian beam is phase-modulated by an SLM at the conjugate plane of the fiber input facet, so that the transmitted beam is focused to a spot near the output facet. We optimize the phases of 16 × 16 macropixels sequentially to maximize the output intensity at the focus50 (Supplementary Information, sec. 1.4). The focal spot can be placed anywhere within the field of view defined by the fiber core size and NA. We choose the focus to be 20 μm outside the output facet (in the air) to avoid damage to the fiber. Figure 5b shows that, upon optimization, the focal spot size (D ≈ 3.4 μm at e−2 of the maximum intensity) is almost at the diffraction limit (D ≈ 3.3 μm) that is determined by the fiber core NA ≈ 0.3. We also measure the phase of the transmitted field, and the flat phase across the focal spot confirms the diffraction-limited focusing. The power within the focus is ~0.7 of the total output power, close to the limit for phase-only modulation of a Gaussian beam (Supplementary Information, sec. 2.4).
Since the formation of a tight focus comes from the interference of many fiber modes, multimode excitation leads to SBS suppression. We measure the SBS thresholds when focusing the output light at different distances dout from the fiber axis. On-axis focusing (dout = 0) results in a 1.8× increase of the threshold over FM-only excitation [Fig. 5c]. Moving the focus away from the fiber axis further increases the threshold, up to 3.1× enhancement at dout ≈ 9.5 μm. This is because forming an off-axis focus needs an increased number of participating modes, e.g., >70 modes for focusing at dout ≈ 9.5 μm. We also demonstrate this with 186-ns laser pulses at 1550 nm, confirming the broad applicability of our method for simultaneously achieving a high SBS threshold and controlling the output-beam profile. Moreover, it is experimentally confirmed that the multimode excitation by input wavefront shaping does not cause any spectral broadening of the transmitted light (see Supplementary Information, sec. 1.5, for more details).
Discussion
We note that SBS was previously used for beam cleanup in MMFs, by transferring the forward-propagating power in HOMs to backward Stokes power in the FM8,9,11,12,14,15. Above the SBS threshold, the backward Stokes exhibits irregular pulsation of intensity12, as shown in Fig. S1b of Supplementary Information. Such pulsation could be suppressed by seeding the Stokes from the distal end of the fiber, which would add complexity to the implementation.
Instead of utilizing SBS, we suppress SBS to achieve stable high-power delivery below the enhanced SBS threshold. Wavefront shaping of input light also enables a smooth output beam. While the SBS threshold with multimode excitation exceeds 3× of the FM-only excitation in the same MMF, we note that the FM-only threshold in our fiber is already ~4× higher than that in a typical single-mode fiber, leading to a total increase by an order of magnitude. The SBS threshold and focusing quality can be further improved by gaining full control over all the fiber modes, requiring amplitude and phase modulation of input light for both polarizations. Our theory predicts the SBS threshold enhancement of 4.5× in our MMF with complete control of a narrowband input signal (Supplementary Information, sec. 2.3). With output beam control, our method allows utilizing highly multimode fibers with even larger cores (diameter >100 μm), leading to several orders of magnitude increase in threshold48. In terms of output focusing, near-unity (>95%) power concentration in the focal spot has been achieved with complete control of input fields to a MMF49. Since direct amplitude modulation introduces power loss, lossless full-field shaping can be realized using two phase-only SLMs with a distance between them51. The SLM patterns need to be constantly adjusted to stabilize the beam profile against temporal drift and fluctuations of the fiber. In our current experiment, the 50-m-long MMF, loosely coiled and placed on an optical table without temperature stabilization and mechanical isolation, drifts on the time scale of 0.5–3 h. The wavefront optimization currently takes ~12 min, while recent works show output refocusing in less than a second52,53. It is also noteworthy that an output beam profile other than a focal spot can be obtained by tailoring the input wavefront54,55.
While we demonstrate the SBS suppression in passive MMFs, our scheme is applicable to MMFs with optical gain, providing a robust route toward further power scaling for high-power fiber amplifiers. Furthermore, focusing an amplified output to a diffraction-limited spot by input wavefront shaping has been realized experimentally56. In addition, our approach can suppress other nonlinear effects such as stimulated Raman scattering40 and transverse mode instability43.
Finally, while the proof-of-concept experiments are conducted on standard MMFs, our method is readily adopted for specialty fibers and combined with other schemes of SBS suppression29,30,31,32,33,34. We envision that wavefront shaping can be a powerful tool to suppress multiple detrimental nonlinear effects while outputting a desired beam profile.
Methods
A detailed description of the optical setup, characterization of SBS, and SLM phase modulation are presented in sec. 1 of Supplementary Information.
Optical setup
In the CW experiment, a fiber amplifier (research unit from Coherent Nufern) seeded by a CW fiber laser with a linewidth of 15 kHz (NP Photonics Rock 1 μm) produces the linearly polarized signal (pump for Brillouin scattering). As illustrated in Fig. S1, the signal beam illuminates a phase-only SLM (Meadowlark HSP1920-500-1200-HSP8) for wavefront shaping. The reflected light from the SLM is split into two; one is directed to a photodetector (PD) to monitor the input power, and the other is coupled into the MMF by an objective lens for multimode excitation or a plano-convex lens with a lower NA for FM-only excitation.
The MMF (Coherent Nufern FUD-3607) is loosely coiled on an optical table without active cooling and mechanical isolation. The transmitted light from the fiber is collected by an objective identical to that at the fiber input, and divided into several beams for simultaneous measurement of near-field and far-field intensity patterns [Figs. 2b, c, e, f, h, i and 5b, c], total power [Fig. 2j], and its temporal fluctuation on the sub-μs scale [Fig. S1c]. In addition to the output intensity profiles, we also measure the phase pattern of the near field in an off-axis holographic setup to confirm diffraction-limited focusing shown in Fig. 5b. Similarly, at the fiber input end, we measure the far-field intensity pattern of backscattered light [Fig. S7], its time-integrated power [Fig. 2j], and temporal fluctuation [Fig. S1b].
In the pulsed experiment, we use a pulsed fiber laser (KEOPSYS, PEFL-E07-LP-040-200-010-W00-G3-T1-ET1-PE30D-CIRFA) that produces 186-ns pulses at a repetition rate of 10 kHz. The optical setup is similar to that of the experiment with a CW laser. A quarter-wave plate is used to convert the polarization state of light from linear to circular before coupling into the MMF. Here a 50-m-long MMF of the same core diameter and NA is used.
Characterization of stimulated Brillouin scattering
The SBS threshold is determined from the dependence of the transmitted power on the input power. The upper panel of Fig. 2j shows that the time-integrated transmitted power first increases linearly with the input power, and then saturates at a certain power, which is set as the SBS threshold. The horizontal axis of Fig. 2j is the transmitted power in the absence of SBS, obtained from the input power and the MMF transmittance for a given launching condition of incident light. The SBS threshold is confirmed by the power variation of backscattered light with input. Below the threshold, the backscattered power, due to Fresnel reflection from the proximal fiber facet and Rayleigh scattering in the fiber, rises gradually with the input power. Once the transmitted power starts to level off, the reflected power shoots up. In the lower panel of Fig. 2j, we subtract the power of linear backscattering (extrapolated from a linear fit of the data below the SBS threshold) from the total backscattered power to show the Stokes power [Fig. S2].
The mean and standard deviation of SBS thresholds in Fig. 3a are obtained from measurements of multiple focal spots with identical distance din to the fiber axis but varying azimuthal angles. The effective number of excited modes in the MMF is given by \({M}_{{{{{{{{\rm{eff}}}}}}}}}={({\sum }_{l}{P}_{l})}^{2}/{\sum }_{l}({{P}_{l}}^{2})\), where Pl is the signal power in mode l.
Phase modulation with spatial light modulator
To obtain the data in Fig. 4, we use the SLM to imprint a random phase pattern on the input beam to the MMF. Each SLM phase pattern comprises ~8 × 8 macropixels over an area covered by the incident Gaussian beam. Each macropixel consists of 144 × 144 SLM pixels, and its phase can be varied independently between 0 and 2π. Reducing the macropixel size increases the number of macropixels and thus the degree of control of input wavefront, but at the cost of diffraction loss from the abrupt phase change between neighboring macropixels.
To further enhance the SBS threshold, we optimize the SLM phase pattern. Starting from a random phase modulation, we arbitrarily select a macropixel, scan its phase from 0 to 2π with a step of π/10, and evaluate the objective function, e.g., difference between the transmitted signal power and the backward Stokes power, for each phase value. After the scan, the phase of this macropixel is set to the value corresponding to the highest objective function. We continue to optimize another macropixel phase till all macropixels’ phases are optimized. The SBS threshold first increases and then saturates after a few rounds of optimization with the same objective function. By switching to a different objective function (e.g., the transmitted signal power), the threshold enhancement may rise slightly after one to two rounds of optimization.
In the experiment presented in Fig. 5, we search for the SLM phase pattern for focusing through a MMF. We monitor the transmitted intensity distribution at the selected plane of focus close to the fiber distal end. The focal spot can be anywhere within the field of view, and its intensity is used as the objective function for optimizing the SLM at the fiber proximal end. The optimization process begins with a flat phase pattern. We scan the phase of individual macropixel from 0 to 2π, and find the value at which the focused power is maximal50. Typically, the power at focus saturates after one or two rounds of optimization. Due to the smooth variation of the optimized phase over neighboring macropixels, the diffraction loss is small, allowing us to increase the macropixel number to ~16 × 16 macropixels [Fig. S4].
Data availability
Data are available at https://doi.org/10.5281/zenodo.835062357.
Code availability
Codes are available at https://doi.org/10.5281/zenodo.835738558.
References
Agrawal, G. in Nonlinear Fiber Optics, 5th edn (ed. Agrawal, G.) 353–396 (Academic Press, 2013).
Stolen, R., Bjorkholm, J. & Ashkin, A. Phase-matched three-wave mixing in silica fiber optical waveguides. Appl. Phys. Lett. 24, 308–310 (1974).
Digonnet, M., Sadowski, R., Shaw, H. & Pantell, R. Resonantly enhanced nonlinearity in doped fibers for low-power all-optical switching: a review. Opt. Fiber Technol. 3, 44–64 (1997).
Kobyakov, A., Sauer, M. & Chowdhury, D. Stimulated Brillouin scattering in optical fibers. Adv. Opt. Photonics 2, 1–59 (2010).
Krupa, K. et al. Multimode nonlinear fiber optics, a spatiotemporal avenue. APL Photonics 4, 110901 (2019).
Wolff, C., Smith, M., Stiller, B. & Poulton, C. Brillouin scattering-theory and experiment: tutorial. J. Opt. Soc. Am. B 38, 1243–1269 (2021).
Wright, L. G., Wu, F. O., Christodoulides, D. N. & Wise, F. W. Physics of highly multimode nonlinear optical systems. Nat. Phys. 18, 1018–1030 (2022).
Bruesselbach, H. Beam cleanup using stimulated Brillouin scattering in multimode fibers. In Conference on Lasers and Electro-Optics paper CThJ2 (Optica, 1993).
Rodgers, B. C., Russell, T. H. & Roh, W. B. Laser beam combining and cleanup by stimulated Brillouin scattering in a multimode optical fiber. Opt. Lett. 24, 1124–1126 (1999).
Brignon, A. & Huignard, J.-P. Phase Conjugate Laser Optics (Wiley, 2004).
Lombard, L., Brignon, A., Huignard, J.-P., Lallier, E. & Georges, P. Beam cleanup in a self-aligned gradient-index Brillouin cavity for high-power multimode fiber amplifiers. Opt. Lett. 31, 158–160 (2006).
Steinhausser, B., Brignon, A., Lallier, E., Huignard, J.-P. & Georges, P. High energy, single-mode, narrow-linewidth fiber laser source using stimulated Brillouin scattering beam cleanup. Opt. Express 15, 6464–6469 (2007).
Thévenaz, L. Slow and fast light in optical fibres. Nat. Photonics 2, 474–481 (2008).
Gao, Q., Lu, Z., Zhu, C. & Zhang, J. High efficient beam cleanup based on stimulated Brillouin scattering with a large core fiber. Laser Part. Beams 32, 517–521 (2014).
Gao, Q., Lu, Z., Zhu, C. & Zhang, J. Mechanism of beam cleanup by stimulated Brillouin scattering in multimode fibers. Appl. Phys. Express 8, 052501 (2015).
Kim, J., Kuzyk, M. C., Han, K., Wang, H. & Bahl, G. Non-reciprocal Brillouin scattering induced transparency. Nat. Phys. 11, 275–280 (2015).
Merklein, M., Stiller, B. & Eggleton, B. J. Brillouin-based light storage and delay techniques. J. Opt. 20, 083003 (2018).
Otterstrom, N. T., Behunin, R. O., Kittlaus, E. A., Wang, Z. & Rakich, P. T. A silicon Brillouin laser. Science 360, 1113–1116 (2018).
Eggleton, B. J., Poulton, C. G., Rakich, P. T., Steel, M. J. & Bahl, G. Brillouin integrated photonics. Nat. Photonics 13, 664–677 (2019).
Murray, J. B., Cerjan, A. & Redding, B. Distributed Brillouin fiber laser sensor. Optica 9, 80–87 (2022).
Pannell, C., Russell, P. S. J. & Newson, T. Stimulated Brillouin scattering in optical fibers: the effects of optical amplification. J. Opt. Soc. Am. B 10, 684–690 (1993).
Dawson, J. W. et al. Analysis of the scalability of diffraction-limited fiber lasers and amplifiers to high average power. Opt. Express 16, 13240–13266 (2008).
Richardson, D. J., Nilsson, J. & Clarkson, W. A. High power fiber lasers: current status and future perspectives. J. Opt. Soc. Am. B 27, 63–92 (2010).
Zervas, M. N. & Codemard, C. A. High power fiber lasers: a review. IEEE J. Selec. Top. Quantum Electron. 20, 219–241 (2014).
Fu, S. et al. Review of recent progress on single-frequency fiber lasers. J. Opt. Soc. Am. B 34, 49–62 (2017).
Limpert, J. et al. Yb-doped large-pitch fibres: effective single-mode operation based on higher-order mode delocalisation. Light Sci. Appl. 1, 8–8 (2012).
Limpert, J. et al. Thermo-optical properties of air-clad photonic crystal fiber lasers in high power operation. Opt. Express 11, 2982–2990 (2003).
Karow, M., Tünnermann, H., Neumann, J., Kracht, D. & Weßels, P. Beam quality degradation of a single-frequency yb-doped photonic crystal fiber amplifier with low mode instability threshold power. Opt. Lett. 37, 4242–4244 (2012).
Kobyakov, A. et al. Design concept for optical fibers with enhanced SBS threshold. Opt. Express 13, 5338–5346 (2005).
Dragic, P. D., Liu, C.-H., Papen, G. C. & Galvanauskas, A. Optical fiber with an acoustic guiding layer for stimulated Brillouin scattering suppression. In Conference on Lasers and Electro-Optics 1984–1986 (IEEE, 2005).
Li, M.-J. et al. Al/Ge co-doped large mode area fiber with high SBS threshold. Opt. Express 15, 8290–8299 (2007).
Robin, C. & Dajani, I. Acoustically segmented photonic crystal fiber for single-frequency high-power laser applications. Opt. Lett. 36, 2641–2643 (2011).
Robin, C., Dajani, I. & Pulford, B. Modal instability-suppressing, single-frequency photonic crystal fiber amplifier with 811 W output power. Opt. Lett. 39, 666–669 (2014).
Hawkins, T. et al. Kilowatt power scaling of an intrinsically low Brillouin and thermo-optic Yb-doped silica fiber. J. Opt. Soc. Am. B 38, 38–49 (2021).
Flores, A., Robin, C., Lanari, A. & Dajani, I. Pseudo-random binary sequence phase modulation for narrow linewidth, kilowatt, monolithic fiber amplifiers. Opt. Express 22, 17735–17744 (2014).
Loftus, T. H. et al. Spectrally beam-combined fiber lasers for high-average-power applications. IEEE J. Selec. Top. Quantum Electron. 13, 487–497 (2007).
Buikema, A., Jose, F., Augst, S. J., Fritschel, P. & Mavalvala, N. Narrow-linewidth fiber amplifier for gravitational-wave detectors. Opt. Lett. 44, 3833–3836 (2019).
Yoshizawa, N. & Imai, T. Stimulated brillouin scattering suppression by means of applying strain distribution to fiber with cabling. J. Light. Technol. 11, 1518–1522 (1993).
Liu, A. Suppressing stimulated brillouin scattering in fiber amplifiers using nonuniform fiber and temperature gradient. Opt. Express 15, 977–984 (2007).
Tzang, O., Caravaca-Aguirre, A. M., Wagner, K. & Piestun, R. Adaptive wavefront shaping for controlling nonlinear multimode interactions in optical fibres. Nat. Photonics 12, 368–374 (2018).
Deliancourt, E. et al. Wavefront shaping for optimized many-mode Kerr beam self-cleaning in graded-index multimode fiber. Opt. Express 27, 17311–17321 (2019).
Teğin, U. et al. Controlling spatiotemporal nonlinearities in multimode fibers with deep neural networks. APL Photonics 5, 030804 (2020).
Chen, C.-W., Wisal, K., Eliezer, Y., Stone, A. D. & Cao, H. Suppressing transverse mode instability through multimode excitation in a fiber amplifier. Proc. Natl Acad. Sci. USA 120, 2217735120 (2023).
Carlson, C. G., Dragic, P. D., Price, R. K., Coleman, J. & Swenson, G. R. A narrow-linewidth, Yb fiber-amplifier-based upper atmospheric Doppler temperature lidar. IEEE J. Selec. Top. Quantum Electron. 15, 451–461 (2009).
Di Teodoro, F., Belden, P., Ionov, P. & Werner, N. High-power ns-pulse fiber laser sources for remote sensors. Opt. Fiber Technol. 20, 688–693 (2014).
Ludewigt, K., Liem, A., Stuhr, U. & Jung, M. High-power laser development for laser weapons. In Proc. SPIE 11162, High Power Lasers: Technology and Systems, Platforms, Effects III 1116207 (SPIE, 2019).
Smith, R. G. Optical power handling capacity of low loss optical fibers as determined by stimulated Raman and Brillouin scattering. Appl. Opt. 11, 2489–2494 (1972).
Wisal, K., Warren-Smith, S. C., Chen, C.-W., Cao, H. & Stone, A.D. Theory of stimulated Brillouin scattering in fibers for highly multimode excitations. Preprint at https://arxiv.org/abs/2304.09342 (2023).
Gomes, A. D., Turtaev, S., Du, Y. & Čižmár, T. Near perfect focusing through multimode fibres. Opt. Express 30, 10645–10663 (2022).
Vellekoop, I. M. & Mosk, A. Phase control algorithms for focusing light through turbid media. Opt. Commun. 281, 3071–3080 (2008).
Jesacher, A., Maurer, C., Schwaighofer, A., Bernet, S. & Ritsch-Marte, M. Near-perfect hologram reconstruction with a spatial light modulator. Opt. Express 16, 2597–2603 (2008).
Caravaca-Aguirre, A. M., Niv, E., Conkey, D. B. & Piestun, R. Real-time resilient focusing through a bending multimode fiber. Opt. Express 21, 12881–12887 (2013).
Feldkhun, D., Tzang, O., Wagner, K. H. & Piestun, R. Focusing and scanning through scattering media in microseconds. Optica 6, 72–75 (2019).
Čižmár, T. & Dholakia, K. Shaping the light transmission through a multimode optical fibre: complex transformation analysis and applications in biophotonics. Opt. Express 19, 18871–18884 (2011).
Leite, I. T. et al. Three-dimensional holographic optical manipulation through a high-numerical-aperture soft-glass multimode fibre. Nat. Photonics 12, 33–39 (2018).
Florentin, R. et al. Shaping the light amplified in a multimode fiber. Light Sci. Appl. 6, 16208–16208 (2017).
Chen, C.-W. et al. Dataset for “Mitigating stimulated Brillouin scattering in multimode fibers with focused output via wavefront shaping.” zenodo https://doi.org/10.5281/zenodo.8350623 (2023).
Wisal, K., Chen, C.-W. & Warren-Smith, S. C. Codes for “Mitigating stimulated Brillouin scattering in multimode fibers with focused output via wavefront shaping.” zenodo https://doi.org/10.5281/zenodo.8357385 (2023).
COMSOL AB. COMSOL Multiphysics version 5.5. www.comsol.com (COMSOL AB, 2023).
Acknowledgements
We thank Yaniv Eliezer at Yale University and Hasan Yılmaz at Bilkent University for stimulating discussions, Nicholas Bernardo and Vincent Bernardo at Yale University for technical assistance, and NP Photonics for the support. We acknowledge the computational resources provided by Yale University and the University of Adelaide. This work was performed in part at the Opto Fab node of the Australian National Fabrication Facility supported by the Commonwealth and SA State Government. This work is supported by the Air Force Office of Scientific Research (AFOSR) under Grants FA9550-20-1-0129 (H.C. and A.D.S.) and FA9550-20-1-0160 (H.E.-H. and D.J.O.), the Australian Research Council (ARC) under CE170100004, and the Next Generation Technologies Fund (NGTF) [Research Agreement 10737] through the NGTF Directed Energy (DE) Science and Technology (S&T) Network of Australian Universities and Industry Partners. The Australian authors acknowledge the support received from the Commonwealth of Australia. S.C.W.-S. is supported by ARC Future Fellowship (FT200100154). H.E.-H. is supported by South Australian Government Future Industry Making Fellowship.
Author information
Authors and Affiliations
Contributions
H.C. proposed the idea and initiated this project; C.-W.C. performed the continuous-wave experiments using the fiber amplifier built by P.A. and analyzed the data in collaboration with K.W., under the supervision of H.C.; L.V.N. and S.W. performed the pulsed experiments and analyzed the data in collaboration with S.C.W.-S., O.H.-S., and E.P.S., under the supervision of H.E.-H. and D.J.O.; K.W. developed the theory and numerical simulations in collaboration with S.C.W.-S. and C.-W.C., under the supervision of A.D.S.; C.-W.C., L.V.N., K.W., A.D.S., and H.C. wrote the manuscript with input from all authors.
Corresponding authors
Ethics declarations
Competing interests
The authors declare no competing interests.
Peer review
Peer review information
Nature Communications thanks Puxiang Lai, Stefan Wabnitz, and Avi Zadok for their contribution to the peer review of this work. A peer review file is available.
Additional information
Publisher’s note Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Supplementary information
Rights and permissions
Open Access This article is licensed under a Creative Commons Attribution 4.0 International License, which permits use, sharing, adaptation, distribution and reproduction in any medium or format, as long as you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons licence, and indicate if changes were made. The images or other third party material in this article are included in the article’s Creative Commons licence, unless indicated otherwise in a credit line to the material. If material is not included in the article’s Creative Commons licence and your intended use is not permitted by statutory regulation or exceeds the permitted use, you will need to obtain permission directly from the copyright holder. To view a copy of this licence, visit http://creativecommons.org/licenses/by/4.0/.
About this article
Cite this article
Chen, CW., Nguyen, L.V., Wisal, K. et al. Mitigating stimulated Brillouin scattering in multimode fibers with focused output via wavefront shaping. Nat Commun 14, 7343 (2023). https://doi.org/10.1038/s41467-023-42806-1
Received:
Accepted:
Published:
DOI: https://doi.org/10.1038/s41467-023-42806-1
Comments
By submitting a comment you agree to abide by our Terms and Community Guidelines. If you find something abusive or that does not comply with our terms or guidelines please flag it as inappropriate.