Abstract
We report the modulation of emission energy, exciton dynamics and lasing properties in a single buckled CdS nanoribbon (NR) by strain-engineering. Inspired by ordered structure fabrication on elastomeric polymer, we develop a new method to fabricate uniform buckled NRs supported on polydimethylsiloxane (PDMS). Wavy structure, of which compressive and tensile strain periodically varied along the CdS NR, leads to a position-dependent emission energy shift as large as 14 nm in photoluminescence (PL) mapping. Both micro-PL and micro-reflectance reveal the spectral characteristics of broad emission of buckled NR, which can be understood by the discrepancy of strain-induced energy shift of A- and B-exciton of CdS. Furthermore, the dynamics of excitons under tensile strain are also investigated; we find that the B-exciton have much shorter lifetime than that of redshifted A-exciton. In addition, we also present the lasing of buckled CdS NRs, in which the strain-dominated mode selection in multi-mode laser and negligible mode shifts in single-mode laser are clearly observed. Our results show that the strained NRs may serve as new functional optical elements for flexible light emitter or on-chip all-optical devices.
Similar content being viewed by others
Introduction
Strain-engineering has been demonstrated to be a very efficient way to tune the optical and electronic properties of materials, which may lead to new functional devices with great flexibility1,2,3,4,5,6,7,8,9. Especially in nanomaterials, high crystal quality and much larger elastic limit because of large surface-volume ratio, facilitate the strain-related new functionalities. Many remarkable reports on tuning electronic and optical properties of diverse nanostructures by strain-engineering have been published8,9,10,11,12,13,14,15,16,17. For example, strain effect on electron-transport of carbon nanotubes1,8; silicon nanomembranes and nanowires10,11,12,13,14; piezoelectricity or optical-mechanical coupling of ZnO, CdS nanowires15,16,17,18,19,20,21,22,23,24; strain-related bandgap-engineering and electronic properties in 2D nanomaterials25,26,27,28. And very recently, hundreds of meV exciton energy shift modulated by strain were observed in both GaAs and CdS nanowires29,30. Undoubtedly, Strain engineering provided a new method to tailor the bandgap of materials instead of traditional ways such as component ratio control, quantum confinement effect.
Nanoribbons (NRs) with an out-of-plane buckled geometry, which have great bendability and mechanical stretchability, are functional nanostructures with great application potential in both electronic and optical device. In last decade, both mechanical and electronic properties of these flexible NR devices have been intensively investigated31,32,33,34,35,36,37. For example, stretchable “wavy” silicon was functioned as flexible field-effect transistors31,32,33,34, the buckled GaAs NRs with very high stretchability and compressibility36, 70% enhancement of piezoelectric effect in wavy PZT ribbons37, etc. Some NRs (e.g. CdS NR, ZnO NR) can also serve as laser sources, waveguides and even semiconductor optical cryocooler, which are building blocks for all-optical on-chip devices38,39,40,41,42,43. It is highly desirable to realize flexible NR-based optical devices, but in above reports, NRs usually have a length of millimeter and perfect alignment along the prestrain direction of elastomeric substrate, which allows for a periodic buckling just via adhesive Van der Waals forces between NRs and elastomeric substrate. Neither of them is fulfilled (maximal hundred micrometers and not good alignment) for CdS or ZnO NRs, thus it is hard to get a periodic buckling with a stable geometry. Moreover, flexibility of NR-based optical devices inevitably induces deformation and thus strain effect on materials which is expected to modulate the optical properties of NR, just like buckled nanowires29. But as far as we know, the optical tuning (e.g. PL, exciton’s dynamics and lasing properties) of NRs by strain-engineering has rarely been investigated before44,45. In this work, CdS, of which nanostructures have been widely investigated in their optical properties46,47,48,49,50,51, is chosen as the test bed because of its high optical quality and very large fracture strength limit30. We present a new method to fabricate wavy structured CdS NRs and studied their optical response to strain. CdS NRs were wrinkled to a nearly uniform buckled structure, which was well characterized by atomic force microscope (AFM) and PL mapping (a periodic emission shift with 14 nm). Moreover, the tuning of emission energy, lifetime of excitons and lasing properties under strain were investigated by using micro-PL, micro-reflectance and time-resolved PL techniques, respectively. This uniform buckled structures and related optical tuning may greatly expand their potential applications in large-scale integrated flexible light-emitting devices.
Experiments and measurements
CdS NRs were grown via the vapor-liquid-solid method at the temperature of 850 °C, which have the wurtzite crystal structure with the [0001] direction (c-axis) perpendicular to the nanoribbon long axis (a-axis)42,52. To measure the optical properties of buckled NRs, we utilized our home-made micro-PL and micro-reflectance setup based on a microscope (as shown in Supplementary Materials, Figure S1). A semiconductor laser (457 nm continuous laser used for PL and 355 nm pulse laser used for lasing) was focused to a spot of ~1 μm by a 50X (NA, 0.5) objective. The emission was collected by the same objective and directed to spectrometer. Spatial scanning measurements were performed in cryostat mounted on a translation stage with the spatial resolution of 1 μm. All the spectral measurements were performed at a temperature of 77 K to ensure that A- and B-exciton of CdS are clearly visible in the spectra. The time-correlated single-photon-counting system (TCSPC) was adopted to study the exciton dynamics.
Results and Discussions
To fabricate out-of-plane buckled CdS NRs, shown in Fig. 1(d), a prestrained PDMS substrate was prepared by a custom-built strain stage. We first dry transferred as-grown CdS NRs from the growth substrate to a polyimide film and then carefully contacted the NRs on polyimide film onto the prestrained PDMS surface and mechanically slid it along the PDMS prestrain direction. In this manner, most NRs are transferred to PDMS with the long axis roughly following the prestrain direction. But unlike the buckled GaAs or PZT ribbons36,37, here, adhesive Van der Waals forces between NRs and PDMS cannot ensure a stable periodic buckled CdS NRs formed. To overcome this limit, we deposited a 5 nm thick Al2O3 film on the NRs by Atom Layer Deposition to tightly fixed NRs on PDMS surface without any influence on PL measurement. A comparison of PL spectra of nanoribbon with and without a layer of Al2O3 and a corresponding discussion are shown in Supplementary Materials (Figure S2). After that, we released the strain of PDMS and obtained CdS NRs with wavy geometry (Fig. 1(a–c)).
The optical image of a typical buckled NR is presented in Fig. 1(d). One can see clearly that the periodic out-of-plane buckled structure of a single CdS NR is formed. To understand its geometrical characteristics, AFM with tapping mode was adopted to scan along the buckled surface of NR and its atomic force micrograph mapping is shown in Fig. 1e (top panel). For clarity, the profile of buckled ribbon (black dots) is also shown at bottom panel; a sinusoidal profile of buckled CdS NR, which is the same as that of buckled silicon ribbons36, is clearly visible. The red curve is the sinusoidal fit to experimental data, from which the amplitude of 2.13 μm and a period of 30.5 ± 1.4 μm are obtained.
Strain-induced exciton energy shifts have been demonstrated in bent ZnO, CdS and GaAs nanowires recently19,29,30. Out-of-plane CdS buckled NRs actually have a similar buckled geometry as bent nanowires, which the tensile strain localized at the outer surface and the compressive strain at the inner surface, respectively. Thus it is expected that the exciton energies of CdS should be modulated by the periodic strain variation of the buckled NR. Figure 2(a) shows the micro-PL spectral mapping, including around 60 spectra measured on the top surface of buckled nanoribbon with a scanning step of ~2.5 μm along the long axis. One can see that the emission peak shifts periodically, which can be attributed to the tensile and compressive strain alternation along the buckled NR. The waterfall plot shown in Supplementary Materials, Figure S3, shows that the maximum redshifted emission peaks (~503.5 nm) and the emission peaks (~489.5 nm) correspond exactly to the crest and the valley of the buckled NR, respectively. Due to the nearly perfect sinusoidal geometry, the redshifted emission peaks measured at six crests of the buckled NR are around 503.5 nm, which show uniform and periodic tuning of emission energy. As mentioned above, the redshift of the exciton emission is attributed to the tensile strain (εtop) localized at the top surface of the crest part, which can be roughly estimated by the local radius of curvature, r and thickness, d, of NR (εtop = d/2r)19. As characterized by AFM, the NR has a thickness of ~0.35 μm and the inscribed circle radius of the crest part is ~2.75 μm. With these values, the tensile strain εtop can be calculated to be around 6.36%, resulting in the redshift of exciton emission of ~14 nm (~68 meV). This redshift amount may be further improved by increasing the pre-tensile strength of PDMS to obtain a larger curvature. For comparison, we also measured the PL spectrum from the flat part of NR on PDMS (as shown in Fig. 2(b), black curve). The red curve (measured at the crest part) is clearly redshifted and the blue curve (obtained from the valley region) shows a little bit blueshift. This is consistent with the previous results of exciton energy under tensile or compressive strain in CdS nanowires29. The redshifted emission peak shows broadening compared to the black spectrum, this can be attributed to the strain gradient distribution both along the thickness direction and along the a-axis of the NR. In addition, other possibility is that bending deformation-induced broadening of the gaps between different subbands in the conduction band of CdS, which was predicted by theoretical calculation29. At last, one should note that the strain-induced piezoelectric field in CdS NRs may affect the PL properties. In regard to this issue, some previous literatures have demonstrated that the influence of piezoelectric field on the PL is strongly dependent on the size of nanostructures and the binding energy of excitons53,54,55. For CdS NRs, it is believed that the PL redshift is dominated by the tensile strain-induced bandgap shift and the piezoelectric field may have slight contribution for thin buckled CdS NRs (~200 nm)54.
Tensile strain induces redshift and broadening of emission peak, but beside that, the other emission peak at the wavelength of 489 nm is always accompanied the redshifted emission peak. This phenomenon is quite similar to the double peaks observed on bent CdS nanowires, in which the PL peak at high energy side was shown to be originating from the emission of B-exciton at inner part (compressive strain part) of a bent nanowire29. But in a buckled NR, we notice that laser mainly excite the tensile part because of penetration depth of laser is no more than 100 nm56,57, Even though 30% of the incident light may penetrate more into the CdS NRs and excite the compressive part, considering that the emission coming from the compressive part may be re-absorbed by the tensile part because of tensile strain-induced redshifted energy band, it is hard to generate a strong emission peak at around 489 nm, as shown in Fig. 2(b). Thus, this phenomenon is totally different from the in-plane bent nanowire where both tensile and compressive parts are covered by the laser spot and the emission peak at 489 nm should not originate from the compressive part. To explore its fundamental properties and the physical mechanism, the micro-PL and micro-reflectance spectral techniques with different polarization configurations were used to study the excitons’ characteristics. To avoid the impacts from resonant modes of cavity, usually formed between the top and bottom surface of thick NR, in the reflectance spectra, a thin NR (thickness, 200 nm) was selected to perform micro-reflectance measurements. Figure 2(c,d) shows the micro-reflectance (c) and micro-PL (d) spectra with different polarization configurations, which are measured from the crest. One can see that the polarization measurements in reflectance show different spectral characteristics for the two emission peaks in PL spectra. As known, CdS has a wurtzite crystal structure, the conduction band is s-like state, whereas the valence band is p-like state, which is split into three bands (labeled as A, B and C) due to the crystal-field effect and spin-orbit interaction58. According to the selection rules, all three excitonic transitions are allowed for transverse electric (TE) polarization (E-field component of light perpendicular to the c-axis of NR), while in transverse magnetic (TM) polarization (E-field component of light parallel to c-axis), the A-exciton is entirely forbidden, while B and C excitons are allowed. The redshifted emission peak (~2.505 eV) is originally TE polarized in both polarized reflectance and PL spectra, which allows us to assign it to A-exciton. Whereas for the emission peak at the high energy side (~2.551 eV), the polarized reflectance spectra show that both TE and TM polarizations are allowed and thus it is reasonable to attribute this emission peak to B-exciton. Compared to the energy difference (~20 meV) between A- (2.540 eV) and B-exciton (2.560 eV) of unstrained CdS29, the tensile strain-induced the A- (2.505 eV) and B-exciton (2.551 eV) energy difference becomes larger (~46 meV) in the buckled CdS NR. This can be understood by the different energy shift trend of A- and B-exciton under uniaxial strain, which has also been experimentally shown in refs [29 and 30]. Experimental study of CdS nanowires show that the A-exciton shifts more than that of B-exciton under the same strain, which explains why we observed a larger energy splitting between A- and B-exciton of buckled NR.
Strain modulates not just the exciton energies but also the dynamics of exciton emission22. Figure 3 (bottom panel) shows the time resolved spectra of A- and B-exciton obtained from the flat part of NR, where the tensile strain effect can be ignored. Fitted by single exponential function, the lifetime of A- and B-exciton was obtained as 1.469 ns and 1.459 ns, respectively. The discrepancy between them is within the time resolution of TCSPS (~50 ps). However, the same measurements at the crest part of buckled NR, where a large tensile strain is applied, show a large lifetime variation for A- and B-exciton (as shown in the top panel). The lifetime of B-exciton becomes much shorter (~1.079 ns), while for A-exciton, it becomes a little longer (~1.573 ns). The difference between them is around 500 ps, which is clearly visible in the time-resolved spectra. This difference can be explained by the enhanced coupling of exciton with LO phonon due to larger energy gap between A- and B-exction. In unstrained CdS NR, the energy gap between A- and B-exciton is around 20 meV, which is much smaller than the LO phonon (~38 meV), this suppressed the decay channel of B-exciton to lower energy via transferring energy to LO phonon59. But the case is totally changed when the tensile strain induced a relatively large energy gap (>50 meV) between A and B excitons, as shown in Fig. 2(c). In this case, the B excitons can decay to the lower energy states efficiently via coupling of exciton and LO phonon. And furthermore, this decay channel may be enhanced by the energy broadening of A- and B- excitons under gradient tensile strain which lead to that the transition rule of exciton decay via LO phonon can be easily satisfied. Carrier’s dynamics plays a key role in light efficiency or response rate of optoelectronic devices and these results show that the strain-induced carrier’s dynamics tuning may be an efficient way to improve the performance of optical devices.
NRs served as nanolaser sources have been widely reported in previous works39,41,42, however, the lasing properties of NR under strain have not been investigated. In our samples, the waveguide cavity formed between the two side edges and the optical gains under pulse laser excitation allow us to realize stimulated emission in single CdS NRs. As shown in Fig. 4 (inset), the emission pattern (lasing) from the NR exhibits interference fringes which result from interference between two laser emitting spots from edges42. The typical laser spectrum measured from the flat part of NR is shown in Fig. 4(a) (black curve) and two lasing modes (labeled as I and II) are visible in the optical gain region near the bandedge. But when we measure the lasing both at the valley part and the crest part, two obvious features are observed in the spectra (blue and red curves). One is that the competition between two lasing mode is modulated by applying different strain. The compressive strain (valley part) supports the lasing mode I, while the tensile strain (crest part) is favorable for the lasing mode II. This behavior can be well explained by the strain-induced gain shift. Initially, lasing mode I is stronger than lasing mode II (black spectrum), which implies that the highest optical gain located at mode I rather than mode II. At valley part, a compressive strain caused the bandedge blueshifted and thus the optical gain regime blueshifted accordingly. This suppressed lasing mode II further and made it invisible in blue spectrum. But at crest part, a tensile strain oppositely induced a redshifted bandedge and the optical gain at lasing mode II would be enhanced, leading to stronger lasing mode II than lasing mode I. The other feature is that the energies of lasing modes are quite stable and change very little with strain. As known, the lasing modes are mainly determined by the cavity length and the refractive index of the material. In the planar waveguide cavity formed along the short axis of NR, the width and the thickness of NR is hardly affected because strain is mainly applied along the long-axis of NR. Since CdS has a large dispersion near the bandedge owing to strong coupling between light and excitons, the energy redshift of A-exciton under tensile strain could modulate the refractive index of CdS and thus the cavity modes’ energies. However, under high excitation power, free electron-hole carriers with a large density are generated and all the empty states around the bandedge are completely occupied, in which case, the refractive index is determined by the carrier density (the quasi-Fermi surface in the conduction and valence band) rather than by the energy band60. So under the same excitation power, the carrier density in the buckled NR is almost the same regardless of strain and thus the influence of strain on the refractive index can be ignored. This is why the energies of lasing modes change very little even though a large tensile or compressive strain is applied. In addition, from a point of view of practical applications, the single-mode nanolaser is highly desirable in the future optical digitized communication and signal processing61,62. Thus we measured a buckled CdS NR with very narrow width (short cavity length, ~1.5 μm) where only one lasing mode is observable in the gain range. Similar to the above multi-mode laser measurements, the lasing spectra measured at the flat part, crest part and valley part of buckled NR are shown in Fig. 4(b). Just as we expected, the lasing mode indeed shifts very little under different strain, which is almost negligible. Furthermore, the emission intensity as a function of excitation power measured at three different strain parts are also presented in Fig. 4(c). Similar to the energies of lasing modes, the threshold of lasing with average power of around 4.7 μW is almost independent of strain. Our results demonstrates that the nanoribbon-based laser sources can retain their optical properties even though a large strain is generated by deformation of devices, this could be very helpful for flexible nanodevices in which the functionalities are not affected by the deformation at all.
Summary and Conclusions
By using a new but relatively easy method, we have fabricated uniform sinusoidal out-of-plane buckled CdS NRs. This led to a periodic modulation of emission energy with wavelength variation of 14 nm. The contribution of A- and B-exciton to the broadening spectrum under tensile strain were studied experimentally by polarized micro-PL and micro-reflectance, the underlying mechanism is believed to be the fact that A-exciton redshift more than B-exciton under the same tensile strain. Besides that, the dynamics of excitons and the lasing properties under strain were also investigated. Buckled CdS NRs may serve as one of optical elements in flexible optoelectronic devices.
Additional Information
How to cite this article: Wang, Q. et al. Emission energy, exciton dynamics and lasing properties of buckled CdS nanoribbons. Sci. Rep. 6, 26607; doi: 10.1038/srep26607 (2016).
References
Tombler, T. W. et al. Reversible electromechanical characteristics of carbon nanotubes under local-probe manipulation. Nature 405, 769–772 (2000).
Ieong, M. et al. Silicon device scaling to the sub-10-nm regime. Science 306, 2057–2060 (2004).
Roberts, M. M. et al. Elastically relaxed free-standing strained-silicon nanomembranes. Nat. Mater. 5, 388–393 (2006).
Sun, X. C. et al. Direct gap photoluminescence of n-type tensile-strained Ge-on-Si. Appl. Phys. Lett. 95, 011911 (2009).
Huo, Y. J. et al. Strong enhancement of direct transition photoluminescence with highly tensile-strained Ge grown by molecular beam epitaxy. Appl. Phys. Lett. 98, 011111 (2011).
Sanchez-Perez, J. R. et al. Direct-bandgap light-emitting germanium in tensilely strained nanomembranes. Proc. Natl. Acad. Sci. USA 108, 18893–18898 (2011).
Smith, A. M. et al. Tuning the optical and electronic properties of colloidal nanocrystals by lattice strain. Nat. Nanotechnol. 4, 56–63 (2009).
Huang, M. Y. et al. Direct measurement of strain-induced changes in the band structure of carbon nanotubes. Phys. Rev. Lett. 100, 106803 (2008).
Someya, T. et al. A large-area, flexible pressure sensor matrix with organic field-effect transistors for artificial skin applications. Proc. Natl. Acad. Sci. USA 101, 9966–9970 (2004).
Choi, W. M. et al. Biaxially stretchable “Wavy” silicon nanomembranes. Nano Lett. 7, 1655–1663 (2007).
Kim, D. H. & Rogers, J. A. Bend, Buckle and Fold: Mechanical Engineering with Nanomembranes. ACS Nano 3, 498–501 (2009).
Wu, Z. G. et al. Charge Separation via Strain in Silicon Nanowires. Nano Lett. 9, 2418–2422 (2009).
Lugstein, A. et al. Anomalous Piezoresistance Effect in Ultrastrained Silicon Nanowires. Nano Lett. 10, 3204–3208 (2010).
Niquet, Y. M. et al. Effects of Strain on the Carrier Mobility in Silicon Nanowires. Nano Lett. 12, 3545–3550 (2012).
Wang, Z. L. & Song, J. H. Piezoelectric nanogenerators based on zinc oxide nanowire arrays. Science 312, 242–246 (2006).
Qin, Y. et al. Microfibre-nanowire hybrid structure for energy scavenging. Nature 451, 809–813 (2008).
Wang, Z. L. ZnO nanowire and nanobelt platform for nanotechnology. Mater. Sci. Eng. R-Rep. 64, 33–71 (2009).
Wang, Z. L. Progress in Piezotronics and Piezo-Phototronics. Adv. Mater. 24, 4632–4646 (2012).
Han, X. B. et al. Electronic and Mechanical Coupling in Bent ZnO Nanowires. Adv. Mater. 21, 4937–4941 (2009).
Liao, Z. M. et al. Strain induced exciton fine-structure splitting and shift in bent ZnO microwires. Sci. Rep. 2, 452 (2012).
Wei, B. et al. Size-Dependent Bandgap Modulation of ZnO Nanowires by Tensile Strain. Nano Lett. 12, 4595–4599 (2012).
Fu, X. W. et al. Exciton Drift in Semiconductors under Uniform Strain Gradients: Application to Bent ZnO Microwires. ACS Nano 8, 3412–3420 (2014).
Lin, Y. F. et al. Piezoelectric nanogenerator using CdS nanowires. Appl. Phys. Lett. 92, 022105 (2008).
Fu, Q. A. et al. Linear strain-gradient effect on the energy bandgap in bent CdS nanowires. Nano Res. 4, 308–314 (2011).
Feng, J. et al. Strain-engineered artificial atom as a broad-spectrum solar energy funnel. Nat. Photonics 6, 865–871 (2012).
He, K. et al. Experimental Demonstration of Continuous Electronic Structure Tuning via Strain in Atomically Thin MoS2. Nano Lett. 13, 2931–2936 (2013).
Conley, H. J. et al. Bandgap Engineering of Strained Monolayer and Bilayer MoS2. Nano Lett. 13, 3626–3630 (2013).
Wu, W. Z. et al. Piezoelectricity of single-atomic-layer MoS2 for energy conversion and piezotronics. Nature 514, 470–474 (2014).
Sun, L. X. et al. Strain-Induced Large Exciton Energy Shifts in Buckled CdS Nanowires. Nano Lett. 13, 3836–3842 (2013).
Signorello, G. et al. Tuning the Light Emission from GaAs Nanowires over 290 meV with Uniaxial Strain. Nano Lett. 13, 917–924 (2013).
Khang, D. Y. et al. A stretchable form of single-crystal silicon for high-performance electronics on rubber substrates. Science 311, 208–212 (2006).
Sun, Y. G. & Rogers, J. A. Structural forms of single crystal semiconductor nanoribbons for high-performance stretchable electronics. J. Mater. Chem. 17, 832–840 (2007).
Kim, D. H. & Rogers, J. A. Stretchable Electronics: Materials Strategies and Devices. Adv. Mater. 20, 4887–4892 (2008).
Khang, D. Y. et al. Mechanical Buckling: Mechanics, Metrology and Stretchable Electronics. Adv. Funct. Mater. 19, 1526–1536 (2009).
Feng, X. et al. Stretchable Ferroelectric Nanoribbons with Wavy Configurations on Elastomeric Substrates. ACS Nano 5, 3326–3332 (2011).
Sun, Y. G. et al. Controlled buckling of semiconductor nanoribbons for stretchable electronics. Nat. Nanotechnol. 1, 201–207 (2006).
Qi, Y. et al. Enhanced Piezoelectricity and Stretchability in Energy Harvesting Devices Fabricated from Buckled PZT Ribbons. Nano Lett. 11, 1331–1336 (2011).
Law, M. et al. Nanoribbon waveguides for subwavelength photonics integration. Science 305, 1269–1273 (2004).
Yan, H. Q. et al. ZnO nanoribbon microcavity lasers. Adv. Mater. 15, 1907–1911 (2003).
Pan, A. L. et al. Optical waveguide through CdS nanoribbons. Small 1, 980–983 (2005).
Xu, J. Y. et al. Room-Temperature Dual-Wavelength Lasing from Single-Nanoribbon Lateral Heterostructures. J. Am. Chem. Soc. 134, 12394–12397 (2012).
Sun, L. X. et al. Resolving Parity and Order of Fabry-Perot Modes in Semiconductor Nanostructure Waveguides and Lasers: Young’s Interference Experiment Revisited. Nano Lett. 14, 6564–6571 (2014).
Zhang, J. et al. Laser cooling of a semiconductor by 40 kelvin. Nature 493, 504–508 (2013).
Li, D. H. et al. Strain-induced spatially indirect exciton recombination in zinc-blende/wurtzite CdS heterostructures. Nano Res. 8, 3035–3044 (2015).
Desai, S. B. et al. Strain-Induced Indirect to Direct Bandgap Transition in Multi layer WSe2. Nano Lett. 14, 4592–4597 (2014).
Van Vugt, L. K. et al. One-dimensional polaritons with size-tunable and enhanced coupling strengths in semiconductor nanowires. Proc. Natl. Acad. Sci. USA 108, 10050–10055 (2011).
Piccione, B. et al. All-optical active switching in individual semiconductor nanowires. Nat. Nanotechnol. 7, 640–645 (2012).
Agarwal, R. et al. Lasing in single cadmium sulfide nanowire optical cavities. Nano Lett. 5, 917–920 (2005).
Oulton, R. F. et al. Plasmon lasers at deep subwavelength scale. Nature 461, 629–632 (2009).
Ren, M. L. et al. Enhanced second-harmonic generation from metal-integrated semiconductor nanowires via highly confined whispering gallery modes. Nat. Commun. 5, 5432 (2014).
Li, D. H. et al. Surface Depletion Induced Quantum Confinement in CdS Nanobelts. ACS Nano 6, 5283–5290 (2012).
Agarwal, R. et al. Real-Time Observation of Morphological Transformations in II–VI Semiconducting Nanobelts via Environmental Transmission Electron Microscopy. Nano Lett. 15, 3303–3308 (2015).
Han, X. B. et al. Strain-Gradient Effect on Energy Bands in Bent ZnO Microwires. Adv. Mater. 24, 4707–4711 (2012).
Xu, S. G. et al. Piezotronic Effects on the Optical Properties of ZnO Nanowires. Nano Lett. 12, 5802–5807 (2012).
Fu, X. W. et al. Strain Loading Mode Dependent Bandgap Deformation Potential in ZnO Micro/Nanowires. ACS Nano 9, 11960–11967 (2015).
Ninomiya, S. & Adachi, S. Optical-properties of Wurtzite CdS. J. Appl. Phys. 78, 1183–1190 (1995).
Li, D. H. et al. Electric-Field-Dependent Photoconductivity in CdS Nanowires and Nanobelts: Exciton Ionization, Franz Keldysh and Stark Effects. Nano Lett. 12, 2993–2999 (2012).
Thomas, D. G. & Hopfield, J. J. Exciton spectrum of Cadmium Sulfide. Phys. Rev. 116, 573–582 (1959).
Cho, C. H. et al. Tailoring hot-exciton emission and lifetimes in semiconducting nanowires via whispering-gallery nanocavity plasmons. Nat. Mater. 10, 669–675 (2011).
Montazeri, M. et al. Transient Rayleigh Scattering: A New Probe of Picosecond Carrier Dynamics in a Single Semiconductor Nanowire. Nano Lett. 12, 5389–5395 (2012).
Xiao, Y. et al. Single-Nanowire Single-Mode Laser. Nano Lett. 11, 1122–1126 (2011).
Gao, H. W. et al. Cleaved-coupled nanowire lasers. Proc. Natl. Acad. Sci. USA 110, 865–869 (2013).
Acknowledgements
This work was supported by the National Natural Science Foundation of China (Grant No: 11474297, 11274330) and Shanghai Pujiang Program (14PJ1409600). L. Sun acknowledges Youth Innovation Promotion Association CAS (2016221). R. Agarwal acknowledges the National Institutes of Health through the NIH Director’s New Innovator Award Program, 1-DP2-7251-01. X.Z acknowledges Shanghai Committee of Science and Technology, China (13ZR1446200).
Author information
Authors and Affiliations
Contributions
Q.W., L.S. and W.L. conceived the idea, designed the experiments and wrote the manuscript; M.-L.R., T.Z. and Y.S. prepared samples used in experiments; Q.W., L.S. and J.L. contributed to time-resolved measurement and interpretation; Y.H., X.Z. and B.Z. each participated in the experiment and contributed to the data analysis; C.C., X.S. and R.A. discussed the results and reviewed the manuscript.
Ethics declarations
Competing interests
The authors declare no competing financial interests.
Electronic supplementary material
Rights and permissions
This work is licensed under a Creative Commons Attribution 4.0 International License. The images or other third party material in this article are included in the article’s Creative Commons license, unless indicated otherwise in the credit line; if the material is not included under the Creative Commons license, users will need to obtain permission from the license holder to reproduce the material. To view a copy of this license, visit http://creativecommons.org/licenses/by/4.0/
About this article
Cite this article
Wang, Q., Sun, L., Lu, J. et al. Emission energy, exciton dynamics and lasing properties of buckled CdS nanoribbons. Sci Rep 6, 26607 (2016). https://doi.org/10.1038/srep26607
Received:
Accepted:
Published:
DOI: https://doi.org/10.1038/srep26607
This article is cited by
-
Enhanced linear and nonlinear optical response in CuS/Ag2S nanocomposites
Applied Physics A (2021)
Comments
By submitting a comment you agree to abide by our Terms and Community Guidelines. If you find something abusive or that does not comply with our terms or guidelines please flag it as inappropriate.