Abstract
We have systematically investigated the wideband slow light in two-dimensional material graphene, revealing that graphene exhibits much larger slow light capability than other materials. The slow light performances including material dispersion, bandwidth, dynamic control ability, delay-bandwidth product, propagation loss and group-velocity dispersion are studied, proving graphene exhibits significant advantages in these performances. A large delay-bandwidth product has been obtained in a simple yet functional grating waveguide with slow down factor c/vg at 163 and slow light bandwidth Δω at 94.4 nm centered at 10.38 μm, which is several orders of magnitude larger than previous results. Physical explanation of the enhanced slow light in graphene is given. Our results indicate graphene is an excellent platform for slow light applications, promoting various future slow light devices based on graphene.
Similar content being viewed by others
Introduction
In recent years, slow light has attracted extensive attentions due to its potential for optical memory which is one of the most challenging components1 in optical integrated circuits. Optical signal in a media with refractive index n has a light speed of , whereas the slow-down factor2 (S factor) which describes how many time light has been slowed is defined as:
the S factor is strongly dependent on two issues: the material index nmat and the material dispersion dnmat/dω. According to Eq. (1), large S factor can be achieved in the materials whose nmat is large or whose dispersion dnmat/dω is large. However, the largest material index available in nature is only 4 for germanium3, indicating that the slow light capabilities of natural materials are poor4. On the other hand, the material dispersion is usually small in conventional materials. The material dispersion increases near the index resonances that rarely occur at resonance frequencies of noble metals such as gold and silver, where absorption becomes a problem.
Novel materials are required to improve the slow light capacity5. Recently the two-dimensional (2D) material graphene has shown unprecedented ability to enhance the light-matter interaction5,6. Especially, a large material index of 69.34 has been reported in graphene which is more than one order of magnitude larger than other materials7. Ref. 8 disclosed an extremely large dispersion in well-designed graphene sheet, revealing the possible dispersion engineering in graphene. It is therefore inferred that graphene has promising potential in slow light. In addition, the large actively-control of graphene’s permittivity9 may enable freedom to control the slow light performances during operation that has not been seen in natural materials. The one-atomic thickness of graphene has intrinsic advantage to minimize the footprint of slow light devices10. However, until now a clear physical understanding and a systematic investigation of the slow light capability in graphene have not been fully explored.
In this paper, a comprehensive study of slow light propagation on graphene is performed, including material index, slow light bandwidth, dynamic control ability, delay-bandwidth product, propagation loss and group-velocity dispersion. It can be concluded that graphene has shown significant advantages in all these aspects. A largely improved delay-bandwidth product has been obtained after optimizations with S factor of 163 and slow light bandwidth Δω of 94.4 nm, which is rarely seen in other materials. Physical understanding of the improved slow light capability is further explained. It is concluded that graphene exhibits large slow light capability, therefore can serve as an excellent slow light platform.
Results and Discussion
Large material dispersion
Owing to the one atomic layer thickness, graphene’s material properties are highly tunable with external environmental parameters such as temperature, chemical potential, scattering rate7,8,9, etc. The surface conductivity can be modelled following the Kubo formula11, from which the surface (2D) permittivity can be derived. For convenience, in Fig. 1 the effective material index (nmat) is calculated from the surface permittivity. The real part of nmat shows monotonic decrease if the considered wavelength increases from 6 μm to 15 μm. nmat also decreases with the increase of chemical potential. For small wavelength and small chemical potential, the material index values are high, e. g. for wavelength at 6 μm, nmat is several orders of magnitude larger if compared with natural materials. This is in accordance with Vakil and Engheta’s observation that freestanding graphene exhibits a high refractive index of 69.347 (called large material dispersion of graphene). Moreover, because ω > 0 and dnmat/dω > 0, in Eq.(1) the S factor of graphene is proportion to its material index. As the material’s indices in Fig. 1 are large, the S factors of graphene are then expected to be large accordingly, e. g. at chemical potential of 0.15 eV and wavelength around 6 μm, the S factor is expected to be larger than 170. The extreme large values of nmat in Fig. 1 indicate that light speeds in graphene can be slowed intensively, where S factors are much larger than conventional materials.
Structural dispersion
Previous knowledge in photonic crystals has suggested that periodical repeated patterns are able to enlarge the dispersion2. E. g. A periodically repeated ring-shaped air holes was used in photonic crystal waveguide to engineer the dispersion curve12; the position of air holes has been shift to obtain a U type dispersion curve which improved the overall delay-bandwidth product13; Chen et al. developed a graded-grating-loaded plasmonic waveguide for slow waves in telecom and infrared frequencies14, etc. In all these studies, periodical repeated patterns have shown strong influences to the structure’s response to different frequencies, which is highly related to the second item in the right side of Eq. (1)15. Following this methodology, here two lines of triangle-shaped air holes are periodically added on the surface of the graphene sheet, as depicted in Fig. 2. The length of the horizontal side in triangle is = 1000 nm, the periodicity for the grating is chosen to be P = 1205 nm and the gap between the two lines of air holes is = 400 nm. To facilitate the simulation, a freestanding graphene with 2D effective index methodology7 is considered here. Light is incident into the grating along the gap between the two lines of air holes.
In Fig. 3, the electric energy distribution of the potential modes in frequency domain are plotted as colorful contour map. By searching the maximum electric energy in the spectrum, the high intensity energy peaks are marked as while circle line in Fig. 3, indicating the existence of the intrinsic guiding modes8,16. The dispersion curve which records the relation between frequencyand wave number are then obtained. The details of energy spectrum calculation can be found in method. The obtained guiding modes in Fig. 3 not only ensure the confinement of light but also provide the single mode propagation. Furthermore, it can be seen clearly that the dispersion curve is made up of two high intensity energy peak regions: one is k approaching 0 and the other is k close to band edge. This is in accordance with previous finding15 that light is conducted under two mechanisms in periodical structures: the index-guiding mechanism where kx approaches 0 and the gap-guiding mechanism where kx is close to the band edge. The conjunction of the two parts are affected by the inserted air holes.
The ratio of the dispersion curve (denoted as S factor) is depicted in Fig. 4, where the S factor curve exhibits a decrease-constant-decrease curve shape, called “stair-like” slow light17. One significant feature is that a large flat region is observed in the middle of the S factor curve, which is apparently different with previous slow light publications in graphene5,8,18. The flat region in the curve ensures a wide band slow light operation in Fig. 4, where different frequency components inside the bandwidth can be delayed to the same speed. This is very important for slow light devices because different light speeds between different frequencies may cause seriously signal distortions that affect the slow light performances. To rigorous investigate the flat feature, the concept of flat ratio is used13, defined as the , where is the average value, as depicted in the insert picture of Fig. 4. If we regard 10% as flat S factor threshold, which is only half value to ref. 13, the obtained slow light bandwidth is 89.6 nm under S factor centered at 110.3 and bandwidth centered at 29 THz. Furthermore, the dispersion curve in Fig. 3 and the S factor curve in Fig. 4 are compared. In Fig. 3, a linear flat dispersion curve can be observed for the frequencies around 29 THz where the curve inside the bandwidth maintains the same ratio. This corresponds to the constant S factor of 110.3 in Fig. 4 for frequencies from 28.86 THz to 29.15 THz. Rigorous calculation shows a large slow light bandwidth of 89.6 nm can be achieved. It should be mentioned large S factor usually leads to limited bandwidth17. As a reference, previously the reported bandwidth is only 2.4 nm for S factor around 96 in a well-designed photonic crystal waveguide13. The significantly increased slow light bandwidth in graphene reveals that the slow light capability has been improved.
Let’s take a deeper look into the physical understanding of the improved slow light capability in graphene. The material dispersions in natural available materials are low. Therefore, previous researchers try to enlarge the dispersion by well-designed periodical structures. However, the new material graphene is demonstrated to provide several orders of magnitude larger material index than other materials, thus a much larger material dispersion can be obtained by the material itself, which is facilitate to slow down the light speed. In this paper, we used graphene as slow light material to obtain large material dispersion and simultaneously designed periodical structure to enlarge the structural dispersion. Such arrangements ensure the designed device can benefit from both large material dispersion and large structural dispersion, both of which can contribute to the improvement of slow light capacity.
The dynamical control ability
One of the major advantages of graphene is its large active-controlled permittivity under the external environment parameter variations, such as temperature T, charged particle scattering rate Γ, angle frequency ω and chemical potential μ. Among these parameters, the chemical potential μ in graphene is directly linked to the external applied gate-voltage that provides a convenient approach to control graphene’s permittivity. The chemical potential is defined as:
where VAG = Vg − VDirac is the external applied voltage, VF is the Fermi velocity and η = 9 × 1016m−2v−1 19. The direct control of graphene’s chemical potential provides a flexible but convenient way to tune the slow light performance: By applying different external voltages, graphene’s permittivity can be changed, thus the slow light performances can be influenced. The emerging of graphene with slow light waveguide has provided an unprecedented way to dynamically control the performances.
Figure 5 shows the S factor curves under different chemical potentials. The shift of the chemical potential does not affect the stair-like slope of the curves but influences the constant S factor value. When the chemical potential is gradually increased from 0.15 eV to 0.3 eV, the constant S factor decreased from 130 to 80. This is expected, because the permittivity of graphene decreases when the chemical potential increases, resulting in the decrease of the dispersion curve ratio (the S factor). On the other hand, the slow light bandwidth for constant S factor moves to higher frequency and the bandwidth increases with chemical potential.
We would like to highlight the convenience of dynamic control ability via graphene sheet. The slow light performances including the S factor, bandwidth, frequency can be modified by the external applied voltage. Please note that the control method via graphene here can be implemented during the slow light operation without re-fabrication or modification of the device, which is quite different from previous slow light controls20,21.
The delay-bandwidth product
Although the S factor represents the degree of slow down, it is not a full picture of slow light performances. There exists a compromise between the S factor and the corresponding slow light bandwidth. Neither emphasizing S factor nor bandwidth is unfair, e. g. a large S factor but narrow bandwidth pulse would causes signal distortion. Therefore, the concept of normalized delay-bandwidth product (NDBP) is introduced as an overall parameter to estimate the slow light performances17 (see methods).
Here we take a full sweep of the geometrical parameters including the waveguide width wg, the height Hs and the width of the holes (see Fig. 6(a)). Additionally, since the ratio between Hs and represents the zenith angle of the triangular hole, we only need to consider one of them. In the following discussion, we set Hs at 680 nm, while sweeping ws and wg simultaneously. The triangular width ws is taken from 700 nm to 1100 nm with an increasing step of 50 nm, while the waveguide width wg is taken from 200 nm to 600 nm with an increasing step of 50 nm. The obtained slow down factor, slow light bandwidth and NDBP are shown in Fig. 6(b–d), respectively. All the slow light bandwidth and NDBP are obtained under flat ratio 10% which is a strict constraint if compared with previous publications13,15,16,20. Because not all considered parameters have stair-like S factor curves, the optimization criterion here is: If there is stair-like S factor curve, the S factor and bandwidth are calculated from the flat region as depicted in Fig. 4; If there is no stair-like curve but a monotonically increasing curve, we fixed the S factor at 150 and calculate the corresponding bandwidth with the restrain of flat ratio 10%. As can be seen in Fig. 6(b), there are three regions for large S factor >175, which have common feature that wg range from 500 nm to 550 nm. However, the optimizations show three maximum slow light bandwidth Δω regions in Fig. 6(c), one is around (wg, ws) centered at (400 nm, 800 nm), one is around (wg, ws) centered at (600 nm, 900 nm), the other one is wg from 400 nm to 550 nm and around 1000 nm. These three regions show maximum bandwidth Δω larger than 89 nm which is extremely large value than previous results13,15,16,20,21. It should be noted that there exist an overlap region for (wg,ws) centered at (500 nm, 1000 nm) where both S factor and bandwidth are large, which indicates a large NDBP value. As the NDBP is the product of and Δω, NDBP should be the compound results from both and Δω. However, interestingly, we found the optimization result of NDBP in Fig. 6(d) is similar with the Δω result in Fig. 6(c), while the S factor in Fig. 6(b) has few influence to the final NDBP result. It is then inferred that the bandwidth has dominated contribution of configuring NDBP. In Fig. 6(d), the largest NDBP value 1.48 occurs at = 550 nm and = 1000 nm, where the S factor is 163 and Δω is 94.4 nm.
The Loss and the GVD
Rigorous simulations are used here to estimate the propagation loss in the waveguide. A Gaussian pulse is injected into the waveguide with wg of 400 nm and chemical potential μ of 0.2 eV, as depicted in Fig. 7(a). From previous band calculation results in Fig. 4, a wide flat bandwidth from 28.9 THz to 29.1 THz has been observed under these parameters. Thus here we set the Gaussian pulse centered at 29 THz with a width of 0.2 THz. The source is located 1000 nm away from the waveguide to avoid the injection perturbation. Four time monitors are added along the propagation direction with an interval distance of 1205 nm. Loss can be estimated by compare the peak values of optical energies. The ratio of peak energies between monitor 2 and 1, monitor 3 and 2, monitor 4 and 3 are −27.1 dB, −27.8 dB and −27.3 dB, respectively. Before we make further comment on the loss, the S factor can also be estimated in Fig. 7 by counting the envelope’s peak movement. The time delay between monitor 2 and 1, monitor 3 and 2, monitor 4 and 3 are 440 fs, 440 fs and 434 fs, respectively, which corresponds to the same S factor of 109.8 between the adjacent monitors. The pulse result of S factor at 109.8 is in good accordance with previous result of S factor of 110.3 from band calculation in Fig. 4, which proves the accuracy of the simulation. It should be pointed out that the obtained loss values here are not high, if consider they are retrieved under the large S factor of 110. Because the slow light loss is proportional to the corresponding S factor20,22. E. g., as a comparison, ref. 20 records a loss around 30 dB in silicon-based grating waveguide under the same S factor 110. Smaller loss can be achieved if shitting the S factor to smaller values, which can be done in terms of increasing the chemical potential in Fig. 5.
Group velocity dispersion (GVD) is the phenomenon that the group velocity of light in a medium highly depends on the optical frequency. A simple way to evaluate the GVD parameter of the proposed waveguide can also be derived from Fig. 7. The GVD parameter can be estimated by measuring the broadening of the pulse. The waist of the pulse during the pulse propagation can be quantified by the Full-Width Half-Maximum (FWHM) value. In our simulation, the FWHM of the pulses at monitor 1, 2, 3 and 4 are 1430 fs, 1454 fs, 1480 fs and 1506 fs, respectively. Thus the pulse broadening between monitor 2 and 1, monitor 3 and 2, monitor 4 and 3 are 24 fs, 26 fs and 26 fs, respectively. As a consequence, it can be concluded that the pulse with a waist length around 1430 fs has been broadened by only 25 fs after propagating 1.205 μm distance. Taking the slow light bandwidth 89.6 nm into account, this means the broadening of the pulse is only 0.32 fs per nanometer wavelength change and per micrometer propagation distance. This corresponds to a GVD parameter of 0.32 fs·nm−1·μm−1, which is an extremely low GVD value if compared with previous results12,23,24,25, e. g. the obtained GVD is two orders of magnitude smaller than ref. 25 and one order of magnitude smaller than ref. 12. It should be pointed out that this ultra-low GVD is retrieved when the S factor is large at 110 and corresponding bandwidth is large at 89.6 nm.
Conclusion
In summary, we employed 2D material graphene to slow down and actively control the light speed. Systematical investigations of slow light performances were performed. By optimizing the material dispersion and structural dispersion, the improved slow light capability has been obtained and the results showed an extremely large NDBP value with c/vg at 163 and Δω at 94.4 nm, which is larger than previous results. The dynamical control of the wide band slow light with ultra-low GVD effect has been demonstrated. It can be concluded that graphene exhibits significant advantages in all the figure of merits in slow light, showing great potential in future light memories and optical integrated circuits.
Methods
Material modeling
It was theoretically demonstrated and experimentally verified that, graphene’s conductivity can be modeled following the Kubo formula as below:
where fd(ε) is the Fermi function, e is the electric charge, is the plank constant, ω is the angular frequency and Γ is the scattering rate. When σg > 0, the whole graphene sheet acts like a thin metallic layer which facilitates the propagation of surface plasmon polaritons. The 2D permittivity of graphene can be obtained from the dispersion relation of SPP below:
Where β is the propagation constant, k0 is the wavenumber in vacuum, η0 is the intrinsic impedance of free space. The material’s refractive index nmat can be estimated via .
Dispersion curve calculation
The dispersion curves are calculated from a special technology from rigorous Finite Difference Time Domain method. In the calculation, one unit cell of the designed periodical structure is considered where the Bloch boundary condition is applied in the propagation direction and the perfectly matched layer absorbing boundary condition is applied in the other direction. We placed one randomly phased dipole source in the optimized position (where the intrinsic modal energy is maximum) to excite the waveguide mode as strong as possible. 10 monitors are randomly placed inside the unit cell to record the electromagnetic wave evolution with time. Symmetrical condition can be used to accelerate the calculation according to the polarization state. After running simulation with sufficient time, some of the excited modes will decay which is the inappropriate modes for the structure (the fake modes) and the modes let in the simulation region are the intrinsic modes of the structure. The fields in the time monitors are then collected and transferred to the frequency domain by appropriate Fourier transformation. To get accurate spectrum in frequency domain, the time domain data need to be apodization filtering to isolate the instant response of the light source. The frequency domain energy spectrum (the colorful contour map in Fig. 3) is obtained by adding the Fourier transformation of all the time monitors together, then the energy peaks in the spectrum identifies the intrinsic mode (contain the information of eigen-frequency f and wavenumber k). By sweeping the wavenumber value k as input, we obtained the full information of the frequency domain energy spectrum. The dispersion curve can be derived by searching the energy peak values of eigen-frequency f under each k in the frequency domain energy spectrum (the white circle line in Fig. 3).
Delay-bandwidth product calculation
Delay-bandwidth product contains the information of both delay and bandwidth, thus it is a relatively fair way to evaluate the slow light performance. Its normalized form, the normalized delay-bandwidth product (NDBP) is more frequently used, defined by:
The average group index is calculated by:
Additional Information
How to cite this article: Hao, R. et al. Improved Slow Light Capacity In Graphene-based Waveguide. Sci. Rep. 5, 15335; doi: 10.1038/srep15335 (2015).
References
Yanik, M. F. & Fan, S. Slow light: Dynamic photon storage. Nat. Phys. 3, 372–374 (2007).
Krauss, T. F. Slow light in photonic crystal waveguides. J. Phys. Appl. Phys. 40, 2666 (2007).
De La Rue, R. M. Optical delays: Slower for longer. Nat. Photonics 2, 715–716 (2008).
He, S., He, Y. & Jin, Y. Revealing the truth about ‘trapped rainbow’ storage of light in metamaterials. Sci. Rep. 2, 583 1:9 (2012) 10.1038/srep00583.
Lu, H. et al. Graphene-based active slow surface plasmon polaritons. Sci. Rep. 5, 8443 1:7 (2015) (10.1038/srep08443).
Koppens, F. H. L., Chang, D. E. & García de Abajo, F. J. Graphene Plasmonics: A Platform for Strong Light–Matter Interactions. Nano Lett. 11, 3370–3377 (2011).
Vakil, A. & Engheta, N. Transformation Optics Using Graphene. Science 332, 1291–1294 (2011).
Hao, R., Jin, J., Peng, X. & Li, E. Dynamic control of wideband slow wave in graphene based waveguides. Opt. Lett. 39, 3094–3097 (2014).
Ooi, K. J. A., Chu, H. S., Ang, L. K. & Bai, P. Mid-infrared active graphene nanoribbon plasmonic waveguide devices. J. Opt. Soc. Am. B 30, 3111 (2013).
Brar, V. W., Jang, M. S., Sherrott, M., Lopez, J. J. & Atwater, H. A. Highly Confined Tunable Mid-Infrared Plasmonics in Graphene Nanoresonators. Nano Lett. 13, 2541–2547 (2013).
Hanson, G. W. Dyadic Green’s functions and guided surface waves for a surface conductivity model of graphene. J. Appl. Phys. 103, 064302 (2008).
Säynätjoki, A., Mulot, M., Ahopelto, J. & Lipsanen, H. Dispersion engineering of photonic crystal waveguides with ring-shapedholes. Opt. Express 15, 8323–8328 (2007).
Hao, R. et al. Novel slow light waveguide with controllable delay-bandwidth product and utra-low dispersion. Opt. Express 18, 5942–5950 (2010).
Chen, L. et al. Broadband slow-light in graded-grating-loaded plasmonic waveguides at telecom frequencies. Appl. Phys. B 104, 653–657 (2011).
Hao, R. et al. Improvement of delay-bandwidth product in photonic crystal slow-light waveguides. Opt. Express 18, 16309–16319 (2010).
Xu, Y., Zhang, J. & Song, G. Slow Surface Plasmons in Plasmonic Grating Waveguide. IEEE Photonics Technol. Lett. 25, 410–413 (2013).
Baba, T. Slow light in photonic crystals. Nat. Photonics 2, 465–473 (2008).
Zhou, H. et al. Enhanced four-wave mixing in graphene-silicon slow-light photonic crystal waveguides. Appl. Phys. Lett. 105, 091111 (2014).
Hao, R. et al. Ultra-compact optical modulator by graphene induced electro-refraction effect. Appl. Phys. Lett. 103, 061116 (2013).
Casas-Bedoya, A. et al. Slow-light dispersion engineering of photonic crystal waveguides using selective microfluidic infiltration. Opt. Lett. 37, 4215–4217 (2012).
Zhao, Y., Zhang, Y. & Wang, Q. Optimization of Slow Light in Slotted Photonic Crystal Waveguide With Liquid Infiltration. J. Light. Technol. 31, 2448–2454 (2013).
Caer, C., Le Roux, X. & Cassan, E. Enhanced localization of light in slow wave slot photonic crystal waveguides. Opt. Lett. 37, 3660–3662 (2012).
Hou, J., Gao, D., Wu, H., Hao, R. & Zhou, Z. Flat Band Slow Light in Symmetric Line Defect Photonic Crystal Waveguides. IEEE Photonics Technol. Lett. 21, 1571–1573 (2009).
Tang, J. et al. Wideband and Low Dispersion Slow Light in Lattice-Shifted Photonic Crystal Waveguides. J. Light. Technol. 31, 3188–3194 (2013).
Ma, J. & Jiang, C. Demonstration of Ultraslow Modes in Asymmetric Line-Defect Photonic Crystal Waveguides. IEEE Photonics Technol. Lett. 20, 1237–1239 (2008).
Acknowledgements
This work was supported by the National Basic Research Program of China (No. 2014CB340005), the National Natural Science Foundation of China under Grant 61575174, Grant 61205054 and Grant 61571395, the Zhejiang Provincial Natural Science Foundation of China under Grant LR16F05002 and the Excellent Young Faculty Awards Program (Zijin Plan) at Zhejiang University.
Author information
Authors and Affiliations
Contributions
R.H. proposed the idea, supervised the simulations, interpreted the results and wrote the manuscript. X.L.P. and J.M.J. carried out the simulations. Y.X. and X.M.Z. plotted the figures. E.P.L. and H.S.C. supervised the whole work, interpreted the results and improved the manuscript. All authors reviewed the manuscript.
Ethics declarations
Competing interests
The authors declare no competing financial interests.
Rights and permissions
This work is licensed under a Creative Commons Attribution 4.0 International License. The images or other third party material in this article are included in the article’s Creative Commons license, unless indicated otherwise in the credit line; if the material is not included under the Creative Commons license, users will need to obtain permission from the license holder to reproduce the material. To view a copy of this license, visit http://creativecommons.org/licenses/by/4.0/
About this article
Cite this article
Hao, R., Peng, XL., Li, EP. et al. Improved Slow Light Capacity In Graphene-based Waveguide. Sci Rep 5, 15335 (2015). https://doi.org/10.1038/srep15335
Received:
Accepted:
Published:
DOI: https://doi.org/10.1038/srep15335
This article is cited by
-
Energy Plasmon Modes in Metamaterial-filled Double-layer Graphene-wrapped Cylindrical Waveguides
Plasmonics (2021)
-
Terahertz electromagnetic fences on a graphene surface plasmon polariton platform
Scientific Reports (2017)
-
Modulating Plasmonic Sensor with Graphene-Based Silicon Grating
Plasmonics (2017)
Comments
By submitting a comment you agree to abide by our Terms and Community Guidelines. If you find something abusive or that does not comply with our terms or guidelines please flag it as inappropriate.