Abstract
A MAX phase Ti3AlC2 thin film is demonstrated as a saturable absorber (SA) to induce Q-switching in the 2.0 μm region. The Ti3AlC2 thin film is sandwiched between two fiber ferrules and integrated into thulium doped fiber laser (TDFL) and thulium-holmium doped fiber laser (THDFL) cavities. Stable Q-switched pulses are observed at 1980.79 nm and 1959.3 nm in the TDFL and THDFL cavities respectively, with repetition rates of 32.57 kHz and 21.94 kHz and corresponding pulse widths of 2.72 μs and 3.9 μs for both cavities. The performance of the Ti3AlC2 based SA for Q-switching operation indicates the high potential of other MAX phase materials to serve as SAs in future photonics systems.
Similar content being viewed by others
Introduction
Q-switched fiber lasers are highly desired laser sources for a wide number of applications due to their potential to produce high energy pulses for use in applications such as sensors1, micromachining2,3 and medical systems4,5,6. Recently, Q-switching in the 2 micron region has received increasing interest due to its various applications such as optical communications7, remote sensing8 and in particular for biological and medical applications9. Q-switched lasers operating at 2.0 µm have been demonstrated for various applications such as the treatment of skin discoloration due to melasma pigmentation10,11,12 by multiple passes with a large spot size laser13, as well as for the removal of tattoos14,15,16,17,18,19. Additionally, Q-switched fiber lasers operating at this region are also highly suitable for micromachining applications such as engraving20,21,22,23,24, cutting25,26, micro-welding27,28 and drilling29,30.
While erbium doped fibers (EDFs) are the most commonly used gain medium in fiber lasers31, efficient operation in the 2.0 µm region is instead achieved by the use of thulium (TDF)32, holmium (HDF)33 and thulium-holmium34 doped fibers (THDF). Of the three, the TDF is the most popular choice due to its broad emission from 1.6 to 2.2 micron35. As such, thulium doped fiber lasers (TDFLs) and thulium-holmium doped fiber lasers (THDFLs) are typically used to develop high power and stable ultra-short pulses in the 2.0 µm region with wideband wavelength tuning36,37,38,39. Originally, these pulses are generated by active methods, such as acoustic-optic modulators (AOMs)40 or electric-optic modulators (EOMs)41, though these cavities suffer from limitations due to their bulk, complex operation and expensive fabrication42,43. As such, passive method have now become the focus of research efforts, due to their significantly simpler design, lower cost and easier fabrication44,45.
Of the may techniques to generate passive Q-switching in a fiber laser cavity, saturable absorbers (SAs) are the most common46. SAs are typically classified as either artificial and real, with artificial SA typically formed by exploiting various nonlinear optical phenomenon such as nonlinear polarization rotation (NPR)47 and nonlinear optical loop mirrors (NOLMs)48,49. Real SAs on the other hand are materials based, such as semiconductor saturable absorber mirrors (SESAMs)50, carbon nanotubes (CNTs)51,52, graphene53,54, topological insulators (TIs)55,56, black phosphorus (BP)57,58, transition metal dichalcogenides (TMDs)59, transition metal oxides (TMOs)60,61 and alcohol62. Recently as well, the discovery of the optical properties of MXene has made it a potential SA material63,64. The synthesis of MXene requires an etching of a MAX phase, commonly by using a combination of strong fluoride ion (F−) etching solutions, hydrochloric acid (HCl) and lithium fluoride (LiF)65. The fabrication process of the MAX phase material would therefore minimize time and cost as it does not require the etching process and thus the need to use strong etching solutions. Furthermore, MAX phase composes of layered ternary transition-metal carbides that have both metal and ceramic properties, which could be useful for high-temperature applications66. The MAX phase is also stiff, oxidation resistant and lightweight in terms of its ceramic properties, while the metallic properties causes it to have good thermal and electrical conductivity, machinability, damage tolerance and thermal shock resistance67,68.
In this work, Q-switched pulse generation in TDFL and THDFL cavities using MAX phase thin film Ti3AlC2 based SAs are proposed and demonstrated. The fabrication of MAX phase Ti3AlC2 as an SA saves one step in comparison to the fabrication of MXene while still having the potential to produce Q-switched pulses. The proposed SA has not been widely used and never been demonstrated in 2 μm region to the best of author’s knowledge. Hence, the potential of Ti3AlC2 to realize Q-switched pulse in 2 μm region is investigated in two different gain mediums where the proposed laser would complement the current fiber laser technology.
Characterizations of Ti3AlC2-PVA Film
The elemental composition of the Ti3AlC2 MAX phase is determined by energy dispersive X-ray (EDX) analysis and the results are presented in Fig. 1. As shown in Fig. 1(a), the EDX elemental mapping clearly shows titanium (Ti), aluminum (Al), and carbon (C) elements and therefore indicates the successful preparation of the Ti3AlC2 MAX phase. The three elements are distributed homogeneously on the surface of Ti3AlC2. To further confirm the chemical composition of the Ti3AlC2 MAX phase, EDX spectroscopy is undertaken and the results shown in Fig. 1(b). The EDX spectrum of Ti3AlC2 shows strong signals corresponding to its main elements including Ti, Al, and C. The presence of these elements with the absence of other impurities elements verify the formation of the Ti3AlC2 MAX phase.
The morphological properties of Ti3AlC2 are observed by field emission scanning electron microscope (FESEM) analysis using a Hitachi SU8220 FESEM. Figure 2 shows the FESEM images of the Ti3AlC2 MAX phase acquired at different magnifications. It can be seen that the Ti3AlC2 MAX phase is built up from alternating Ti-C and Al layers, forming a lamellar structure as can be seen in Fig. 2(a,b). From the high magnification image given in Fig. 2(c), it can be clearly observed that all the layers are tightly packed together as a result of the metallic bond between each layers that connects them.
A mode-locked laser operating at 1566 nm with a repetition rate of 27.7 MHz and a pulse width of 0.70 ps is used to measure the nonlinear response of the Ti3AlC2 by the balanced twin-detector method. A variable attenuator is introduced in the measurement system to control the input power into Ti3AlC2. It must be noted that in this work a mode-locked laser output at 2.0 μm could not be used due to the lack of necessary equipment. The nonlinear saturable absorption curve of the Ti3AlC2 MAX phase is given in Fig. 3.
The nonlinear saturable absorption curve of the Ti3AlC2 is taken by fitting the intensity-dependent absorption equation into the measured data:
The parameters Δα, ISat and αns are modulation depth, saturation intensity and non-saturable loss, respectively. The modulation depth and non-saturable loss of Ti3AlC2 are computed to be 58.41% and 41.59%, respectively.
Experimental setup
The cavity setup for Q-switched TDFL and THDFL are given in Fig. 4. It is imperative to note that for both the TDFL and THDFL, the overall cavity is the same, with only the gain medium changed. For the cavity, two Princeton Lightwave Inc PSL 450 1550 nm laser diodes (LDs) with maximum powers of 240 mW each are used to optically pump the 4 m long TmDF200 TDF that is commercially available from OFS Inc. The TDF has a cutoff wavelength of 1350 nm and an absorption coefficient of about 200 dBm−1 at 790 nm and 22 dBm−1 at 1550 nm. The TDF is optically pumped through the 1550 nm port of 1550/2000 nm wavelength division multiplexers (WDMs), where 1550 nm isolators (ISOs) are used between LDs and ports of the WDMs to prevent any back-reflections from damaging the LDs.
Schematic of laser cavity for Q-switched pulse generation in TDFL and TDHFL. This figure was drawn using SketchUp Make 2017 (Basic), Software Version: Windows 64-bit 17.2.2555, available at https://www.sketchup.com/download/all.
A 2000 nm ISO is placed after 2000 nm port of the WDM to ensure the unidirectional propagation of the signal in the cavity. A 90:10 optical coupler (OC) is connected to the ISO output to extract 10% from the intra-cavity light for analysis. The 90% port of the OC continues to travel in the cavity, where it encounters the Ti3AlC2 based SA which induces pulsing in the propagating signal. The SA is sandwiched between two fiber connectors and held by an FC/PC connector to form the SA assembly. The output from the SA is then connected to the 2000 nm port of the WDM to complete the optical cavity. The incorporation of a polarization controller (PC) is not needed as Q-switched pulses can be observed once the MAX phase Ti3AlC2 film is incorporated into the laser cavity, without the need of a further optimization of the polarization states in the cavity.
For the configuration of the THDFL, the same cavity setup is used, with the only difference being the replacement of the TDF with a 1.5 m long CorActive TH512 thulium-holmium doped fiber as the gain medium. The THDFL has a cut-off wavelength of between 1650 nm to 1750 nm and an absorption coefficient of 120 dBm−1 at around 790 nm as well as 15 dBm−1 at 1550 nm.
Results and Discussion
Thulium-doped fiber laser (TDFL) with Ti3AlC2
A pure PVA film is first tested in both the TDFL and THDFL cavities to observe any pulse lasing existence, but only continuous wave (CW) lasing is observed even when the pump power is increased to its maximum. This confirms that the Q-switching effect is induced by the Ti3AlC2. Furthermore, it is also proven that there is no absorption by the pure PVA film in the UV spectrum69, thus confirming that the PVA film has no role in inducing the Q-switched output other than being a host material. When configured as a TDFL, CW lasing is obtained at a pump power of 75.56 mW and a stable Q-switched pulse train is achieved when the pump power reaches 80.84 mW. A maximum pump power of 112.55 mW is observed for the Q-switched operation of the TDFL, as any higher pump powers will result in significant fluctuations and instabilities of the pulses. This is attributed to the SA beginning to suffer the effects of optical damage but has not yet experienced any significant damage as lowering the pump power results in a stable pulse train being obtained once again. This implies that the SA could only withstand a corresponding power intensity of about 0.44 MW/cm2 before the Q-switching performance started to degrade. The Q-switched output has an average output power of 0.67 mW to 1.43 mW for a pump power of 80.84 mW to 112.55 mW. Figure 5(a) shows the optical spectrum of the Q-switched pulses at a pump power of 112.55 mW with a center wavelength of 1980.79 nm, where the full width at half maximum (FWHM) of the spectrum is 7.51 nm. The laser appears broader than usual, and this is attributed to the self-phase modulation (SPM) effect in the cavity that takes place when a high intensity laser propagates through the fiber.
In Fig. 5(b,c), the pulse train and single pulse profile are taken in the time domain using an OSC at a maximum pump power of 112.55 mW. The pulse train shows a uniform pulse intensity with a repetition rate of 32.57 kHz and the single pulse shows a pulse width of 2.72 μs. The pulses do not fluctuate significantly throughout the measurement, with uniform shape and pulse intensity. The behaviors of pulse repetition rate and pulse width are observed by varying the pump power from 80.84 mW to 112.55 mW. The repetition rate and the pulse width are 20.44 kHz to 32.57 kHz and 5.92 μs to 2.72 μs, respectively as shown in Fig. 5(d), where the repetition rate and the pulse width are inversely proportional to each other as the pump power increases. The pulse width decreases at a constant rate until the maximum pump power value shows that the SA has not reached its saturation limit yet. Increasing the pump power above the maximum value will cause the degradation of the SA and result in a higher Q-switching threshold of the SA initially, and if continued to operate above the maximum pump power the possible failure of the SA.
In Fig. 6, the pulse energy as well as peak power are calculated over the Q-switching pump power range. The pulse energy and the peak power in Fig. 6(a,b) show the highest pulse energy generated at the pump power of 109.03 mW and the highest peak power at the pump power of 112.55 mW, which are 45.23 nJ and 15.49 mW respectively. In addition, a signal-to-noise ratio (SNR) at 32.57 kHz in the frequency domain is measured by using RFSA at a pump power of 112.55 mW as shown in Fig. 7. The output pulse has an average SNR of 51.11 dB, which is comparable to other Q-switched lasers that have SNRs of more than 40 dB70. The stability of the peak is measured for 60 minutes at 5 minute intervals. The peak shows no significant fluctuations throughout the observation period, thus showing a stable Q-switched system. The same can be said about the laser’s output power, as any fluctuation in the laser’s output power would affect the intensity of the Q-switched pulses and hence will also be reflected in the intensity of the RF spectrum.
Thulium-holmium doped fiber laser (THDFL)
In the THDFL configuration, CW lasing is obtained at a pump power of 85.8 mW before a stable Q-switched pulse train is obtained when the pump power reaches 91.54 mW. It is worth to note that the Q-switching threshold is lower in the TDFL as compared to that of THDFL. This is due to the TDF having a higher absorption at 1550 nm as compared to the THDF, which allows the TDF to absorb the pump signal more efficiently. The pump power is then gradually increased until a maximum pump power of 123 mW, above which major fluctuations and instabilities are observed in the pulses due to it nearing the SA’s saturation limit. The average output power was measured to be 0.48 mW to 1.29 mW at a pump power range of 91.54 mW to 123 mW. The optical spectrum of the Q-switched at a pump power of 123 mW has a center wavelength of 1959.3 nm and FWHM of 5.25 nm as shown in Fig. 8(a). As with the case of the TDFL, the high intensity lasing in the cavity induces the SPM effect and results in the broadening of the laser spectrum.
The pulse train and single pulse profile at maximum pump power of 123 mW are taken in the time domain using an OSC as shown in Fig. 8(b,c). A uniform pulse intensity with a repetition rate of 21.94 kHz and a pulse width of 3.9 μs are shown in the pulse train and single pulse profile, respectively. Throughout the measurement, the pulses maintain uniform shape and pulse intensity, indicating a stable Q-switched laser output. In Fig. 8(d), the pump power is varied from 91.54 mW to 123 mW to study the behavior of pulse repetition rate and pulse width. The repetition rate and the pulse width are 13.81 kHz to 21.94 kHz and 12.05 μs to 3.9 μs, respectively, and are proportionally inversed to each other as the pump power increases. The pulse width has a sudden drop from 12.05 μs to 8.8 μs when the pump power increases from 91.54 mW to 93.46 mW, but gradually decreases above a pump power of 93.46 mW until the maximum value. The exponential decline of the pulse width shows that the SA is nearing its saturation limit, especially for a pulse width from 4.12 μs to 3.9 μs which appears to reduce only minimally.
Pulse energy and peak power are calculated with respect to the Q-switched pump power range. The pulse energy and the peak power in Fig. 9(a,b) show the highest pulse energy generated at the pump power of 123 mW and the highest peak power at the pump power of 123 mW, which are 58.72 nJ and 15.06 mW, respectively. Furthermore, the pulse peak in frequency domain is also measured using a RFSA to verify the phase noise and to evaluate the stability of the system as shown in Fig. 10. The pulse peak at 21.94 kHz corresponds well with the repetition rate of the pulses at maximum pump power and the average SNR of the peak is measured to be 45.88 dB, which is notably high. The test for peak stability is taken for 60 minutes, where every measurement is taken at 5 minutes interval. A stable Q-switched system is displayed as no major fluctuation occurs at the peak throughout the period.
The cavity is also tested without the incorporation of the Ti3AlC2 for both configurations. In this case, both configurations show no sign of Q-switching at any pump power level, hence confirming the thin film Ti3AlC2 is responsible solely for inducing the Q-switching effect. In addition to that, no mode-locking phenomenon is observed in both of the laser cavities using the Ti3AlC2 SA. We believe this is due to the high non-saturable loss of the SA as well as the high intracavity loss in the laser cavity. Mode-locking operation could be obtained by using a high-quality SA with low non-saturable loss71, by controlling the loss of the cavity as well as by adjusting the polarization states of the intracavity signal using a PC. The performance of the Q-switched lasers in 2.0 μm region with different thin films are compared in Table 1.
From the table, it can be seen that the minimum pulse width and maximum repetition rate of TiO2 and MoS2 surpass both MoSe2 and Ti3AlC2, which are 1.91 μs and 1.76 μs as well as 36.96 kHz and 48.10 kHz, respectively. Furthermore, the maximum pulse energy generated from TiO2 and MoS2 also exceed that of MoSe2 and Ti3AlC2, which are 0.3 μJ and 1 μJ, respectively. Nevertheless, the performance of Ti3AlC2 is comparable to MoSe2, where the minimum pulse width and the maximum repetition rate of MoSe2 are 5.50 μs and 21.80 kHz, which are both below Ti3AlC2 of 2.72 μs and 32.57 kHz for TDFL and 3.90 μs and 21.94 kHz for THDFL. The maximum pulse energy of MoSe2 is 0.042 μJ, slightly lower than Ti3AlC2 in TDFL and THDFL, which are 0.045 μJ and 0.058 μJ, respectively. Although current works on the MAX phase Ti3AlC2 thin film are limited, it can still produce Q-switched pulses with considerably good performance. Furthermore, the optical damage threshold limitation can also be overcome by having the SA materials interact with the TDFL or THDFL through the evanescent wave of the propagating beam, as opposed to being directly exposed to the signal. This can be achieved by using a tapered fiber, with the material being sprayed at the waist of the tapered fiber72, and can realize higher output powers from both cavities.
Methods
Preparation of Ti3AlC2-PVA film
The Ti3AlC2 powder is purchased from Laizhou Kai Kai Ceramic Material Co. Ltd. and polyvinyl alcohol (PVA) with MW ~ 31,000 is obtained from Sigma Aldrich. In order to form the Ti3AlC2-PVA film, solution casting is employed with the PVA as the host polymer. Approximately 100 mg of Ti3AlC2 powder is ultrasonicated for 16 hours in 20 mL of deionized water (DIW) to form a homogeneous solution with an initial concentration of 5 mg/mL. Any undissolved powder is separated from the homogeneous dispersion by centrifugation at 3000 rpm for 15 minutes, and the supernatant is collected for further use. At the same time, the PVA solution with a concentration of 5 mg/mL is prepared by dissolving 100 mg of the PVA powder in 20 mL of DIW while being stirred at 60 °C until the powder is totally dissolved. 10 mL of each solution is then mixed together in a beaker. The mixture is stirred for 2 hours while on a hot plate at 60 °C before being poured into a petri dish and put it in an over at 60 °C for process.
Laser characterization
The optical spectrum of the Q-switched laser is analyzed using a Yokogawa AQ6370B optical spectrum analyzer (OSA) with a wavelength range from 1200 nm to 2400 nm, while a 10 GHz Newport 818-BB-51F photodetector (PD) with a responsivity of 0.95 A/W at 2000 nm is used for time and frequency domain analysis. A Keysight DSOX3102T oscilloscope (OSC) with a bandwidth of 1 GHz and an Anritsu MS2683A radio frequency spectrum analyzer (RFSA) are used to monitor the output in time and frequency domain, respectively.
Conclusion
This work successfully demonstrates Q-switched operation at the 2.0 μm region in TDFL and THDFL incorporating thin film Ti3AlC2 as a new SA, capable of producing stable pulse with kilohertz repetition rates and microsecond pulse widths. The Q-switched pulses operating wavelength for TDFL and THDFL are observed at 1980.79 nm and 1959.3 nm, respectively. Furthermore, maximum repetition rates of 32.57 kHz and 21.94 kHz as well as minimum pulse widths of 2.72 μs and 3.9 μs are observed at maximum pump power of 112.55 mW and 123 mW for the TDFL and THDFL, respectively. Besides that, uniform pulse intensity and stable pulses are shown in each laser output, with the average SNRs of 51.11 dB and 45.88 dB for TDFL and THDFL, respectively. The MAX phase Ti3AlC2 based SA can complement the current application of fiber laser technology.
References
Sharma, U., Chang-Seok, K. & Kang, J. U. Highly stable tunable dual-wavelength Q-switched fiber laser for DIAL applications. IEEE Photonics Technol. Lett. 16, 1277–1279 (2004).
Shephard, J. D. et al. Improved hollow-core photonic crystal fiber design for delivery of nanosecond pulses in laser micromachining applications. Appl. Opt. 44, 4582–4588 (2005).
Leone, C., Papa, I., Tagliaferri, F. & Lopresto, V. Investigation of CFRP laser milling using a 30 W Q-switched Yb:YAG fiber laser: Effect of process parameters on removal mechanisms and HAZ formation. Compos. Part A Appl. Sci. Manuf. 55, 129–142 (2013).
Skorczakowski, M. et al. Mid-infrared Q-switched Er:YAG laser for medical applications. Laser Phys. Lett. 7, 498–504 (2010).
Ivanenko, M. M., Fahimi-Weber, S., Mitra, T., Wierich, W. & Hering, P. Bone tissue ablation with sub-μs pulses of a Q-switch CO2 laser: histological examination of thermal side effects. Lasers Med. Sci. 17, 258–264 (2002).
Fried, N. M. & Murray, K. E. High-power thulium fiber laser ablation of urinary tissues at 1.94 μm. J. Endourol. 19, 25–31 (2005).
Li, Z. et al. Diode-pumped wideband thulium-doped fiber amplifiers for optical communications in the 1800–2050 nm window. Optics express 21, 26450–26455 (2013).
Gao, C. et al. Q-switched ceramic lasers for remote sensing. SPIE Newsroom, https://spie.org/news/5359-q-switched-ceramic-lasers-for-remote-sensing (2014).
Letokhov, V. S. Laser biology and medicine. Nature 316, 325–330 (1985).
Jung, J. W., Kim, W. O., Jung, H. R., Kim, S. A. & Ryoo, Y. W. A face-split study to evaluate the effects of microneedle radiofrequency with Q-switched Nd:YAG laser for the treatment of melasma. Ann. Dermatol. 31, 133–138 (2019).
Wattanakrai, P., Mornchan, R. & Eimpunth, S. Low-fluence Q-switched neodymium-doped yttrium aluminum garnet (1,064 nm) laser for the treatment of facial melasma in Asians. Dermatologic Surg. 36, 76–87 (2010).
Polder, K. D. & Bruce, S. Treatment of melasma using a novel 1,927-nm fractional thulium fiber laser: A pilot study. Dermatologic Surg. 38, 199–206 (2012).
Aurangabadkar, S. J. Optimizing Q-switched lasers for melasma and acquired dermal melanoses. Indian Journal of Dermatology, Venereology and Leprology 85, 10–17 (2019).
Yoo, S. W. et al. Non-ablative fractional thulium laser irradiation suppresses early tumor growth. Curr. Opt. Photonics 1, 51–59 (2017).
Leuenberger, M. L. et al. Comparison of the Q-switched alexandrite, ND:YAG, and ruby lasers in treating blue-black tattoos. Dermatologic Surg. 25, 10–14 (1999).
Jones, A., Roddey, P., Orengo, I. & Rosen, T. The Q-switched ND:YAG laser effectively treats tattoos in darkly pigmented skin. Dermatologic Surg. 22, 999–1001 (1996).
Tse, Y., Levine, V. J., Mcclain, S. A. & Ashinoff, R. The Removal of Cutaneous Pigmented Lesions with the Q‐switched Ruby Laser and the Q‐switched Neodymium: Yttrium‐Aluminum‐Garnet Laser: A Comparative Study. J. Dermatol. Surg. Oncol. 20, 795–800 (1994).
Troilius, A. M. Effective treatment of traumatic tattoos with a Q-switched Nd:YAG laser. Lasers Surg. Med. 22, 103–108 (1998).
Nehal, K. S., Levine, V. J. & Ashinoff, R. The treatment of benign pigmented lesions and tattoos with the Q- switched ruby laser: A comparative study using the 5.0- and 6.5-mm spot size. Dermatologic Surg. 22, 683–686 (1996).
Leone, C., Lopresto, V. & De Iorio, I. Wood engraving by Q-switched diode-pumped frequency-doubled Nd:YAG green laser. Opt. Lasers Eng. 47, 161–168 (2009).
Minami, K. et al. YAG laser assisted etching for releasing silicon micro structure. Proc. IEEE 4705940, 53–58, https://doi.org/10.1109/MEMSYS.1993.296951 (1993).
Gower, M. C. Industrial applications of laser micromachining. Opt. Express 7, 56–57 (2000).
Rizvi, N. H., Milne, D. K., Rumsby, P. T. & Gower, M. C. Laser micromachining: new developments and applications. Proc. SPIE 3933, 261–271, https://doi.org/10.1117/12.387562 (2000).
Schaeffer, R. D. Fundamentals of Laser Micromachining (CRC Press, 2012).
Bovatsek, J. M. & Patel, R. S. Highest-speed dicing of thin silicon wafers with nanosecond-pulse 355 nm Q-switched laser source using line-focus fluence optimization technique. in Laser-based Micro- and Nanopackaging and Assembly IV (2010).
Hong, L., Li, L. & Ju, C. Investigation of cutting of engineering ceramics with Q-switched pulse CO2 laser. Opt. Lasers Eng. 38, 279–289 (2002).
Ascari, A. & Fortunato, A. Nanosecond pulsed laser welding of high carbon steels. Opt. Laser Technol. 56, 25–34 (2014).
Ascari, A., Fortunato, A. & Orazi, L. Laser micro-welding of high carbon steels. Rivista Italiana Della Saldatura 65, 507–513 (2013).
Nikumb, S. et al. Precision glass machining, drilling and profile cutting by short pulse lasers. Thin Solid Films 477, 216–221 (2005).
Biswas, R., Kuar, A. S., Sarkar, S. & Mitra, S. A parametric study of pulsed Nd:YAG laser micro-drilling of gamma-titanium aluminide. Opt. Laser Technol. 42, 23–31 (2010).
Digonnet, M. J. F. Rare-earth-doped Fiber Lasers and Amplifiers (CRC Press, 2001).
Wu, J., Yao, Z., Zong, J. & Jiang, S. Highly efficient high-power thulium-doped germanate glass fiber laser. Opt. Lett. 32, 638–640 (2007).
Jackson, S. D. Single-transverse-mode 25-W holmium-doped fluoride fiber laser operating at 286 µm. Opt. Lett. Opt. Lett. 29, 334–336 (2004).
Taniguchi, A. et al. 1212 nm pumping of 2 μm Tm-Ho-codoped silica fiber laser. Appl. Phys. Lett. 81, 3723–3725 (2002).
Stevens, G. & Legg, T. All-fiber widely tunable thulium laser. Proc. SPIE 9728, 972814, https://doi.org/10.1117/12.2203478 (2016).
Yu, H., Zheng, X., Yin, K., Cheng, X. & Jiang, T. Nanosecond passively Q-switched thulium/holmium-doped fiber laser based on black phosphorus nanoplatelets. Opt. Mater. Express 6, 603–609 (2016).
Yu, H., Zheng, X., Yin, K., Cheng, X. & Jiang, T. Thulium/holmium-doped fiber laser passively mode locked by black phosphorus nanoplatelets-based saturable absorber. Appl. Opt. 54, 10290–10294 (2015).
McComb, T. S. et al. High-power widely tunable thulium fiber lasers. Appl. Opt. 49, 6236–6242 (2010).
Yin, K., Zhang, B., Xue, G., Li, L. & Hou, J. High-power all-fiber wavelength-tunable thulium doped fiber laser at 2 μm. Opt. Express 22, 19947–19952 (2014).
Hong, H., Huang, L., Liu, Q., Yan, P. & Gong, M. Compact high-power, TEM00 acousto-optics Q-switched Nd:YVO4 oscillator pumped at 888 nm. Appl. Opt. 51, 323–327 (2012).
Ji, J., Zhu, X., Dai, S. & Wang, C. Depolarization loss compensated resonator for electro-optic Q-switched solid-state laser. Opt. Commun. 270, 301–304 (2007).
Lee, J., Jung, M., Koo, J., Chi, C. & Lee, J. H. Passively Q-Switched 1.89-μm Fiber Laser Using a Bulk-Structured Bi2Te3 Topological Insulator. IEEE J. Sel. Top. Quantum Electron. 21, 31–36 (2015).
Lee, J., Koo, J., Chi, C. & Lee, J. H. All-fiberized, passively Q-switched 1.06 μm laser using a bulk-structured Bi2Te3 topological insulator. J. Opt. 16, 085203 (2014).
Luo, Z. et al. Graphene-based passively Q-switched dual-wavelength erbium-doped fiber laser. Opt. Lett. 35, 3709–3711 (2010).
Fotiadi, A. A., Kurkov, A. S. & Razdobreev, I. M. All-fiber passively Q-switched Ytterbium laser. Proc. IEEE 8803672, 515, https://doi.org/10.1109/CLEOE.2005.1568293 (2005).
Rahman, M. F. A. et al. Q-switched and mode-locked thulium-doped fiber laser with pure Antimony film Saturable absorber. Opt. Commun. 421, 99–104 (2018).
Harun, S. W., Akbari, R., Arof, H. & Ahmad, H. Mode-locked bismuth-based erbium-doped fiber laser with stable and clean femtosecond pulses output. Laser Phys. Lett. 8, 449 (2011).
Aguergaray, C., Broderick, N. G. R., Erkintalo, M., Chen, J. S. Y. & Kruglov, V. Mode-locked femtosecond all-normal all-PM Yb-doped fiber laser using a nonlinear amplifying loop mirror. Opt. Express 20, 10545–10551 (2012).
Szczepanek, J., Kardaś, T. M., Michalska, M., Radzewicz, C. & Stepanenko, Y. Simple all-PM-fiber laser mode-locked with a nonlinear loop mirror. Opt. Lett. 40, 3500–3503 (2015).
Xu, Z., Dou, Z.-Y., Hou, J. & Xu, X.-J. All-fiber wavelength-tunable Tm-doped fiber laser mode locked by SESAM with 120 nm tuning range. Appl. Opt. 56, 5978–5981 (2017).
Meng, Y., Li, Y., Xu, Y. & Wang, F. Carbon nanotube mode-locked thulium fiber laser with 200 nm tuning range. Sci. Rep. 7, 45109 (2017).
Fang, Q., Kieu, K. & Peyghambarian, N. An All-fiber 2-μm wavelength-tunable mode-locked laser. IEEE Photonics Technol. Lett. 22, 1656–1658 (2010).
Sun, Z. et al. Graphene mode-locked ultrafast laser. ACS Nano 4, 803–810 (2010).
Ismail, M. A., Ahmad, F., Harun, S. W., Arof, H. & Ahmad, H. A Q-switched erbium-doped fiber laser with a graphene saturable absorber. Laser Phys. Lett. 10, 025102 (2013).
Jung, M. et al. A femtosecond pulse fiber laser at 1935 nm using a bulk-structured Bi2Te3 topological insulator. Opt. Express 22, 7865–7874 (2014).
Lin, Y. H. et al. Using n- and p-Type Bi2Te3 topological insulator nanoparticles to enable controlled femtosecond mode-locking of fiber lasers. ACS Photonics 2, 481–490 (2015).
Qin, Z. et al. Mid-infrared mode-locked pulse generation with multilayer black phosphorus as saturable absorber. Opt. Lett. 41, 56–59 (2016).
Sotor, J., Sobon, G., Macherzynski, W., Paletko, P. & Abramski, K. M. Black phosphorus saturable absorber for ultrashort pulse generation. Appl. Phys. Lett. 41, 56–59 (2015).
Wu, K., Zhang, X., Wang, J., Li, X. & Chen, J. WS2 as a saturable absorber for ultrafast photonic applications of mode-locked and Q-switched lasers. Opt. Express 23, 11453–11461 (2015).
Zhu, X. et al. Nonlinear optical performance of periodic structures made from composites of polymers and Co3O4 nanoparticles. Appl. Phys. Lett. 97, 093503 (2010).
Mamani, J. B., Gamarra, L. F. & De Souza Brito, G. E. Synthesis and characterization of Fe3O4 nanoparticles with perspectives in biomedical applications. Mater. Res. 17, 542–549 (2014).
Ibarra-Escamilla, B. et al. Passively Q-Switched Thulium-Doped Fiber Laser Using Alcohol. IEEE Photonics Technol. Lett. 30, 1768–1771 (2018).
Jhon, Y. I. et al. Metallic MXene Saturable Absorber for Femtosecond Mode-Locked Lasers. Adv. Mater. 29, 1702496 (2017).
Dong, Y. et al. Saturable Absorption in 2D Ti3C2 MXene Thin Films for Passive Photonic Diodes. Adv. Mater. 30, 1705714 (2018).
Hantanasirisakul, K. et al. Fabrication of Ti3C2Tx MXene Transparent Thin Films with Tunable Optoelectronic Properties. Adv. Electron. Mater. 2, 1600050 (2016).
Song, G. M. Self-healing of MAX Phase Ceramics for High Temperature Applications: Evidence from Ti3AlC2 in Advances in Science and Technology of M n+1AX n Phases (ed. Low, I. M.) 271–288 (Woodhead Publishing, 2012).
Barsoum, M. W. The MN+1AXN phases: A new class of solids: Thermodynamically stable nanolaminates. Prog. Solid State Chem. 28, 201–281 (2000).
Mo, Y., Rulis, P. & Ching, W. Y. Electronic structure and optical conductivities of 20 MAX-phase compounds. Phys. Rev. B - Condens. Matter Mater. Phys. 86, 165122 (2012).
Pandey, S., Pandey, S. K., Vyom Parashar, G. K. & Mehrotraband, A. C. P. Ag/PVA nanocomposites: Optical and thermal dimensions. J. of Materials Chem. 21, 17154–17159 (2011).
Ahmad, H. et al. 70 nm, broadly tunable passively Q-switched thulium-doped fiber laser with few-layer Mo0.8W0.2S2 saturable absorber. Opt. Fiber Technol. 46, 230–237 (2018).
Keller, U. et al. Semiconductor saturable absorber mirrors (SESAM’s) for femtosecond to nanosecond pulse generation in solid-state lasers. IEEE J. Sel. Top. Quantum Electron. 2, 435–453 (1996).
Harun, S. W., Lim, K. S., Tio, C. K., Dimyati, K. & Ahmad, H. Theoretical analysis and fabrication of tapered fiber. Optik. 124, 538–543 (2013).
Latiff, A. A., Rusdi, M. F. M., Hisyam, M. B., Ahmad, H. & Harun, S. W. A generation of 2 μm Q-switched thulium-doped fibre laser based on anatase titanium(IV) oxide film saturable absorber. J. Mod. Opt. 64, 187–190 (2017).
Luo, Z. et al. 1-, 1.5-, and 2-μm fiber lasers Q-switched by a broadband few-layer MoS2 saturable absorber. J. Light. Technol. 32, 4077–4084 (2014).
Woodward, R. I. et al. Wideband saturable absorption in few-layer molybdenum diselenide (MoSe2) for Q-switching Yb-, Er- and Tm-doped fiber lasers. Opt. Express 23, 20051–20061 (2015).
Acknowledgements
We would like to thank the University of Malaya for funding this research under the grants BKS002-2019 and RU011-2019 and the Ministry of Higher Education, Malaysia for funding this research under the grant HiCoE Phase II Funding.
Author information
Authors and Affiliations
Contributions
Harith Ahmad proposed the study and designed the experiment. Aizuddin Ahmad Kamely and Muhamad Zharif Samion performed the experiments for data collection. Norazriena Yusoff prepared the MAX phase Ti3AlC2 and performed the material characterization. Leonard Bayang contributed to data analysis. The results were discussed and all the authors contributed to the writing of the manuscript.
Corresponding author
Ethics declarations
Competing interests
The authors declare no competing interests.
Additional information
Publisher’s note Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Rights and permissions
Open Access This article is licensed under a Creative Commons Attribution 4.0 International License, which permits use, sharing, adaptation, distribution and reproduction in any medium or format, as long as you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons license, and indicate if changes were made. The images or other third party material in this article are included in the article’s Creative Commons license, unless indicated otherwise in a credit line to the material. If material is not included in the article’s Creative Commons license and your intended use is not permitted by statutory regulation or exceeds the permitted use, you will need to obtain permission directly from the copyright holder. To view a copy of this license, visit http://creativecommons.org/licenses/by/4.0/.
About this article
Cite this article
Ahmad, H., Kamely, A.A., Yusoff, N. et al. Generation of Q-switched Pulses in Thulium-doped and Thulium/Holmium-co-doped Fiber Lasers using MAX phase (Ti3AlC2). Sci Rep 10, 9233 (2020). https://doi.org/10.1038/s41598-020-66141-3
Received:
Accepted:
Published:
DOI: https://doi.org/10.1038/s41598-020-66141-3
This article is cited by
-
Silicon photonics-based high-energy passively Q-switched laser
Nature Photonics (2024)
-
Q-switched giant pulsed erbium-doped all-fiber laser with V2ZnC MAX phase saturable absorber
Optoelectronics Letters (2024)
-
Deposition of Ti2AlC MAX phase onto the side polished fiber as saturable absorber for soliton mode-locked fiber laser generation
Optical and Quantum Electronics (2022)
Comments
By submitting a comment you agree to abide by our Terms and Community Guidelines. If you find something abusive or that does not comply with our terms or guidelines please flag it as inappropriate.