Abstract
Deformable elastomeric spheres are evaluated experimentally as they skip multiple times over a lake surface. Some spheres are embedded with small inertial measurement units to measure the acceleration experienced during water surface impact. A model for multiple impact events shows good agreement between measured acceleration, number of skipping events and distanced traveled. The experiment reveals a new mode of skipping, “water walking”, which is observed for relatively soft spheres impacting at low impact angles. The mode occurs when the sphere gains significant angular velocity over the first several impacts, causing the sphere to maintain a deformed, oblong shape. The behavior is characterized by the sphere moving nearly parallel to the water surface with the major axis tips dipping below the water surface with each rotation while the shorter sides pass just above, giving the impression that the sphere is walking across the water surface.
Similar content being viewed by others
Introduction
As early as the late 16th Century, naval gunners knew that a cannonball fired at a sufficiently small impact angle to the water surface could be made to skip across the sea1. The technique simplified targeting because skipping spheres would strike any object along a straight line, rather than only a single point. By the mid 19th century, engineers were investigating how changes in impact angle and sphere density affected the number of skipping events. Notes from experiments collected in 1855 record a 24.5 kg sphere skipping 32 times before entry2. In 1883, de Jonquières discussed that a critical impact angle exists above which skipping does not occur, which is inversely proportional to the square root of the sphere specific gravity (\({\theta }_{c}=18/\sqrt{SG}\))3.
Early efforts to study skipping behavior produced little more than qualitative results4. In 1944, photographic techniques allowed Birkhoff et al. to perform a more complete study and create a model for the forces experienced by a rigid sphere obliquely impacting a liquid surface5. However, Birkhoff’s model is not completely analytical. Other researchers, as well as Birkhoff himself, have noted that more than one assumption in the model is not necessarily true, but provides a good estimate of the forces involved4. Johnson mentions that, “the phenomenon of ricochet [on water] is well known but not widely understood because it takes place in circumstances difficult to control and define… It is a succession of oblique high speed impact events… in which the geometry of each individual strike is different”. Perhaps for this reason, most studies concerning skipping phenomenon focus on single impacts rather than the complete skipping event4. Hewitt et al. studied subsequent water skipping events, more specifically a fixed plane skipping on a moving channel6. The authors identified multiple skipping states or modes and presented several models to explain their qualitative features. While the governing principles are similar, the study by Hewitt et al. differs significantly from an investigation of a freely flying body on a fixed liquid pool. More recently, skipping behavior has been studied in reference to skipping stones. In 2003, Bocquet presented a model which he used to theoretically estimate the maximum number of skips that can be achieved with a skipping stone7. Clanet et al. published an experimental investigation in 2004 which identified optimal values for both impact angle and attack angle8. The model for stone skipping was refined further in light of experimental results by Rosellini et al.9. In 2005, Nagahiro and Hayakawa performed a three-dimensional simulation of stone skipping which produced results in agreement with those discovered by Clanet et al.10.
Deformable skipping spheres were first studied in 2012 when Truscott et al. investigated a water skipping toy known as a Waboba®11. They noted that deformation upon impact appears to increase lift and thus produce more successful skipping. Following publications by the same research group have provided additional insight into why elastomeric spheres skip more readily than their rigid counterparts12,13. Deformation upon impact not only increases cross-sectional area, resulting in greater lift, but also produces more favorable attack angles with the water surface. These previous studies focus primarily on isolated single skip events and only present data collected in a laboratory setting. They did study short multi-skip events (less than four skips), with each impact inducing a predictable deformation mode and type of skip. However, they do not address long multiple skipping events (i.e., number of skips \(\gg 4\)) where one may want to understand how the dynamics change in later skips, or to predict number of skips and distance traveled. As will be shown herein, the physics can indeed be different and require alterations to existing models to describe the observed phenomena.
This paper presents an investigation of the skipping behavior of elastomeric spheres over successive skipping events. The measured results are compared to predictions from a model validated for single skips and extended here to multiple skipping events. Additionally, experimental investigations revealed a previously unknown mode of water surface skipping for elastomeric spheres. The new skipping mode consists of the sphere moving nearly parallel to the water surface while impacting the water rapidly; this gives the impression that the sphere is walking across the water surface. We investigate the causes and behavior of this newly observed phenomenon.
Results
Multiple skip phenomena
A deformable elastomeric sphere impacting a water surface at an oblique angle will, under certain conditions, rebound or skip from the water surface. When this event happens in a large space, the rebounding sphere follows a predictable projectile trajectory before impacting the water a second time13. Depending on the initial impact conditions the sphere can skip once, twice, or several times before losing the energy necessary to skip and (for spheres denser than water such as these) entering the water. The height and distance achieved between skips decreases with each skipping event, just like a skipping stone, with the last few skips before entry typically occurring rapidly with spacing between impact events near one sphere diameter. These rapid impacts just prior to entry are known as “pitty-pat” in the stone skipping community. A photographic example of this type of traditional skipping for elastomeric spheres is presented in Fig. 1(a). A representative trajectory of traditional skipping is presented in Fig. 1(c).
In addition to the skipping behavior described above, the skipping experiments performed at the lake showed that when softer spheres (smaller G) were skipped with lower values of impact angle β0, they would often transition from traditional skipping behavior (always within 3–4 skips), to moving approximately parallel to the water surface with impact events occurring very close together (on the order of one sphere diameter). Photographs of this unique skipping behavior are shown in Fig. 1(b), and it is diagramed in Fig. 1(d). In this mode, the height of skipping events was nearly indiscernible, even from high speed footage. This motion parallel to the water surface, with rapid impact events, gave the impression that the sphere was “walking” across the water surface in a manner reminiscent of the water walking basilisk lizard14. Upon closer inspection of high speed photographs, we observed that spheres demonstrating this behavior exhibited high angular velocity \(\dot{\psi }\) and generally maintained a more pronounced deformed shape during the skipping event (visible in Fig. 1(b)). This deformation is represented by the parameter λ, shown in the inset of Fig. 1(d).
We investigate the differences between this “water walking” behavior and traditional skipping through high speed photographs collected in a more controlled lab setting. Consider the traditional skipping event in shown Fig. 2(a); the ball impacts at a shallow oblique angle, creates a single cavity, then rises above the water surface. The centroid of the sphere image (black diamond) is clearly descending before impact and ascending after impact. The cavity created by this impact sequence is shown in Fig. 2(b). By contrast, the sphere in Fig. 2(c) exhibits water walking. The sphere maintains a more pronounced deformed shape and impact events appear not to come from the sphere descending into the water, but due to the tips of the major axis of the deformed spheroid rotating to interact with the water surface (d). This impact event doesn’t generate enough lift to cause the ball to ascend significantly, but generates sufficient lift to prevent the sphere from descending below the water surface (note the relatively constant height of the centroid). In an extreme case, this behavior was observed to persist for more than 100 surface impact events.
Modeling multiple skip events
This newly observed skipping behavior, as well as traditional skipping events, are investigated in light of the hydrodynamic force model proposed by Belden et al.13. Consider an elastomeric sphere impacting the water surface as shown in Fig. 3. The magnitude and direction of sphere velocity are represented by U and β, with subscripts referring to those values prior to impact (0), at the sphere bottom during impact (B) and upon exiting the water (E). Sphere deformation during impact is represented by principal stretches λ1 and λ2, which describe the ratio of the deformed spheroid axes to the undeformed sphere radius R (see Figs 1(d) and 3). The coordinates of the sphere centroid are (d1, d2) and the attack angle is represented by α and is set by the orientation of the principal stretches of the deformed sphere. The sphere is idealized as an incompressible neo-Hookean hyperelastic solid with shear modulus G and density \({\rho }_{s}\). Belden et al. altered an existing model proposed by Rosellini et al. for circular disks and approximated the wetted area as a circular disk with radius λeqR, modeling the hydrodynamic force as
where Sw is the sphere wetted area. Their published results show that this model predicts the skipping behavior of an elastomeric sphere in terms of impact velocity U0 and impact angle β0 over four subsequent skipping events. However, their paper does not comment on the ability of the model to predict impact force, number of impact events or distance travelled13.
We present two cases, which were characteristic of observed traditional skipping and water walking, and compare the results with model predictions. For each scenario, experimentally measured impact conditions U0,1 and β0,1 (the second subscript refers to the impact number) are used to calculate exit conditions UE,1 and βE,1. Values of UE,N are calculated from the analytical model, and values of βE,N are calculated from a fit to empirical data. These exit conditions were entered into a ballistic model with simplified air drag to calculate the distance of flight and generate values for U0,2 and β0,2. The process was repeated until the impact angle \({\beta }_{0,N} < 0.001^\circ \), at which point the impact was deemed an entry. In this way values for U0, UE, β0, βE and the acceleration magnitude a were modeled for each impact, in addition to predictions for number of skips N and total distance d for each complete skipping event.
For the traditional skipping case, a sphere with radius \(R=0.05\,{\rm{m}}\), material shear modulus \(G=74.4\,{\rm{kPa}}\), specific gravity \(SG=1.07\) and containing a small 6-axis accelerometer was shot toward the water free surface with impact conditions of \({\beta }_{0}=10.7^\circ \) and \({U}_{0}=45.1\) m/s. The sphere skipped in a traditional manner \(N=10\) times and traveled \(d=105\,{\rm{m}}\) before entry. Figure 4(a) presents the acceleration magnitude a for this skipping event (gray lines). The measured acceleration peaks decrease relatively slowly, then decay more quickly between the final and more rapid impacts of “pitty-pat” prior to entry. The impacts in the middle of the skipping event (highlighted in the plot inset) have a magnitude near \(a=50\,g\) with well-defined peaks. The peak values of a for a modeled skipping event with the same initial impact conditions are plotted on the same graph (green marks). The timeline for the modeled and experimental data are aligned at the first impact event. For this case, the model significantly over predicts a for the initial impact, but shows good agreement through the sixth impact event, predicting \(N=12\), \(d=83\,{\rm{m}}\) (measured: \(N=10\), \(d=105\,{\rm{m}}\)) and also accurately predicts a “pitty-pat” event prior to entry. In the model, the impacting object is represented by a disk rather than an oblate spheroid, resulting is an overestimation of the impact forces.
In the water walking case, a sphere with \(R=0.05\,{\rm{m}}\), \(G=12.3\,{\rm{kPa}}\), \(SG=1.07\) and containing a small 6-axis accelerometer was shot toward the water free surface with impact conditions of \({\beta }_{0}=11.8^\circ \) and \({U}_{0}=29.2\) m/s. The sphere skipped in a traditional manner three times before the vertical motion of the sphere all but ceased and the sphere traversed nearly parallel to the water surface. During this time the sphere was striking the water so frequently the splash crowns commonly overlapped. The splash events are so intermingled that it is impossible to count the number of impact events visually from images with confidence. However, individual impact events can be identified via small peaks in the accelerometer data (Fig. 4(b) inset). The experimental sphere was observed to skip \(N=30\) times over a distance of \(d=52\,{\rm{m}}\). The measured and calculated accelerations are shown in Fig. 4(b), where we see the peak a values decreasing more quickly than for the skipping case shown in Fig. 4(a). The peak values of a from a simulated skipping event with the same initial impact conditions for the first skip are plotted on the same graph in Fig. 4(b) (black marks). Again the model significantly over predicts a for the initial impact, but shows good agreement through the seventh impact event, predicting \(N=13\) and \(d=24\,{\rm{m}}\) (measured: \(N=30\), \(d=52\,{\rm{m}}\)). The model accurately predicts a transition to rapid, low acceleration impact events between 3–4 skips, which enables the transition to water walking. However, the model significantly under-predicts both number of skips N and distance travelled d for walking walking cases. This hints at the fact that the dynamics are sufficiently different in this water walking mode compared to traditional skipping, which is well captured by the model.
Research by Belden et al.13 showed that for elastomeric spheres with specific gravity near unity (\(SG\approx 1\)), skipping or entry can be predicted from two dimensionless parameters: G/\({\rho }_{w}{U}_{0}^{2}\) and β0. In Fig. 5(a) G/\({\rho }_{w}{U}_{0}^{2}\) is plotted against β0 for the two mathematically modeled skipping events (i.e., traditional and water-walking) introduced in Fig. 4. The calculations for the traditional skipping event are plotted with dark green squares in Fig. 5(a). Impact angle β0 and impact velocity U0 generally decrease over the skipping event, which ends in water entry (upper-most green square). The modeled water-walking case (black squares) exhibits markedly different behavior. Impact angle β0 decreases rapidly over the first 3–4 skips (transition to water walking was always observed to occur within 3–4 skips in experiments). Impact velocity U0 does not decrease as rapidly as the traditional skipping case. The model then predicts several successive impact events with very low values of β0, yet small changes in G/\({\rho }_{w}{U}_{0}^{2}\) (impact velocity). In other words the model predicts a quick transition to impact events which remain close to the water surface (low impact angles), with minimal change in velocity magnitude, which is characteristic of water walking. The smaller squares represent model-generated skipping events with initial conditions between the walking behavior and the traditional skipping behavior. As G/\({\rho }_{w}{U}_{0}^{2}\) increases, the modeled skipping behavior transitions from characteristics of a water walking event to a traditional skipping event.
Figure 5(b) presents the placement of the initial skip on the regime diagram for all experimental multi-skip events analyzed for this study. Traditional skipping events are indicated by × marks where water walking is indicated with \(\circ \) and Δ marks (differentiated later). Note that water walking was only observed when G/\({\rho }_{w}{U}_{0}^{2} < 0.02\) and \({\beta }_{0} < 20^\circ \) (gray dotted lines). The largest values for d were observed when G/\({\rho }_{w}{U}_{0}^{2}\) and β0 were minimized. Based on the experimentally determined transition value from Fig. 5(b), we apply these initial conditions to a simulation and find the orange result in Fig. 5(a). This simulation qualitatively shows characteristics of the traditional and walking skip types and is thus consistent as a transition between these regimes.
Investigating water walking
A primary difference we observed for water walking compared to traditional skipping is the presence of significant rigid body rotation with a corresponding angular velocity \(\dot{\psi }\) that we observe to be relatively constant throughout the water walking portion of the skipping event. To investigate the role that rotation might play in water walking, we modify the skipping model presented Belden et al.13. They provide a set of equations for the motion of the center of mass (d1, d2) and sphere deformation (λ1, λ2, λ3, α) in terms of general forces and tractions acting on the body. Here, λ1 and λ2 are principal stretches describing the deformation of the sphere, as shown in Fig. 3, and by definition \({\lambda }_{3}=1\)/\({\lambda }_{1}{\lambda }_{2}\) to conserve volume. The principal stretches are aligned with principal axes that, in general, may be rotated by an angle α with respect to the world coordinate frame. We expand the version of the model given by Belden et al. to include rigid body rotation \(\dot{\psi }\); Appendix A (Supplementary Information) contains a full derivation of the model, which yields a set of coupled second order nonlinear ordinary differential equations for d1, d2, λ1, λ2, α and now \(\psi \). By looking for steady-state solutions with a constant rigid rotation rate \(\dot{\psi }\), constant principal axes rotation rate \(\dot{\alpha }\) and all other derivatives and tractions vanishing, the system reduces to two equations of motion relating \(\dot{\psi }\) to the principal stretches λ1 and λ2,
Adding these equations results in
Solving for \(\dot{\psi }\) gives
where \({\rho }_{s}\) is the sphere density. Equation 2 has a family of real solutions requiring \({\lambda }_{1}\ge 1\)/λ2. Rearranging equation 5 gives
Thus equation 6 describes a sphere in steady-state translation and rotation that holds a constant deformed shape described by λ1λ2. This type of skipping event is represented visually in Fig. 6(a). The expression predicts higher values of λ1λ2 for larger values of \(\dot{\psi }\), \({\rho }_{s}\) and R and for smaller values of G. The relationship in equation 6 is plotted as a black line in Fig. 6(c), which predicts an exponential increase in λ1λ2 as \(\dot{\psi }/\sqrt{5G/{\rho }_{s}{R}^{2}}\to 1\). In observed experimental skipping events, λ1 and λ2 are not precisely equal, leading to a slightly oblong configuration as seen in Fig. 6(b). To compare theoretical predictions with observed behavior, the value of λ1λ2 is measured for several experimental cases by measuring the stretches in the plane of motion from high speed images. Angular velocity \(\dot{\psi }\) is measured from high speed video as near to the middle of the skipping event as possible. These experimentally measured values of λ1λ2 are plotted against dimensionless angular velocity for several experimental cases in Fig. 6(c) and follow the predicted trend.
Belden et al.13 showed that natural elastic wave modes excited in the sphere propagate with angular velocity \(\dot{\alpha }\sim \sqrt{5G/{\rho }_{s}{R}^{2}}\), which appears in the denominator of equation 6. The above analysis allows for arbitrary values of \(\dot{\alpha }\), and we expect that elastic waves excited during water impact do indeed propagate within the sphere during water walking skip types. Figure 6(b) shows the kinematics observed in many water walking instances in the field. The sphere assumes a somewhat prolate shape with λ1 > λ2 and rotates with nearly constant rigid rotation rate \(\dot{\psi }\). While difficult to experimentally identify the elastic waves given high sphere rotation, the impact conditions are consistent with mode 1+ elastic waves, which would tend to distort the sphere into the prolate shape13. It is thus interesting to consider the ratio \({\rm{\Omega }}\equiv \dot{\psi }/\sqrt{5G/{\rho }_{s}{R}^{2}}\) in terms of the rigid body rotation rate and the angular velocity of propagating elastic waves, \(\dot{\alpha }\). Empirical results from Belden et al.13 showed that \(\dot{\alpha }=0.83\sqrt{5G/{\rho }_{s}{R}^{2}}\) for mode 1+ elastic waves; substituting this into the expression for \({\rm{\Omega }}\) gives \(\dot{\psi }/\dot{\alpha }={\rm{\Omega }}/0.83\). The vertical lines on Fig. 6(c) correspond to \(\dot{\psi }/\dot{\alpha }=0.5\) and \(\dot{\psi }/\dot{\alpha }=1\), and provide boundaries between three distinct skipping types: traditional skipping, water walking type 1 and water walking type 2. The difference between the two types of walking modes, and their relation to \(\dot{\psi }\)/\(\dot{\alpha }\) is explored next.
Figure 7(c) plots the frequency of impact events f as a function of \(\dot{\psi }\), looking at only water walking cases (For traditional skipping events, the time between impact events decreased dramatically with each impact and did not correlate with \(\dot{\psi }\)). Black markers indicate events where skips could be counted visually. Gray markers indicate events where skips were measured from accelerometer data. The observed water walking can be distinguished by one of two slopes, experiencing impact events approximately once or twice per sphere rotation. In Fig. 7(a) a sphere is shown along with the length over which a single rotation occurred (vertical blue lines). Note that only a single cavity was formed; this type of water walking is identified as type 1 water walking. By contrast, the sphere shown in Fig. 7(b) impacts the free surface two times over a single sphere rotation, exhibiting what we call type 2 water walking. Note that in Fig. 5(b), water walking type 2 only occurs at the smallest values of G/\({\rho }_{w}{U}_{0}^{2}\) and β0.
We have discussed that the coupling between \(\dot{\psi }\) and \(\dot{\alpha }\) play an important role in predicting water walking behavior. We seek additional insight into this observation by considering the position of a single point x on the outer surface of the sphere that is constrained to the e1-e2 plane such that \({\bf{x}}=R\,\cos \,\gamma {{\bf{e}}}_{{\bf{1}}}+R\,\sin \,\gamma {{\bf{e}}}_{{\bf{2}}}\), where γ is a parameter. We assume that the sphere undergoes a rigid rotation through angle \(\psi (t)\) and a volume preserving stretch defined by λ1, λ2 and α(t) (see Appendix A, Supplementary Information). The e2 component of x is differentiated to solve for the value of γ corresponding to the lowest point on the sphere, p(t). Figure 7(c) plots p(t) over a full period of rigid rotation for different ratios of \(\dot{\psi }\)/\(\dot{\alpha }\).
For small values of \(\dot{\psi }\)/\(\dot{\alpha }\), deformation is minimal and the lowest point of the sphere, p(t), varies little over a single rotation (Fig. 7(c)),which would produce only small scale disturbances on the cavity surface. At the other extreme, when \(\dot{\psi }\)/\(\dot{\alpha }\) = 1, the amplitude of p(t) is significant and there are two large valleys in one period of rigid rotation. This corresponds to the onset of water walking type 2, in which two distinct cavities are formed in one sphere rotation period (as shown in Fig. 7(c)). For \(0.5 < \dot{\psi }\)/\(\dot{\alpha } < 1\), the amplitude of p(t) is smaller and the frequency is larger. We would therefore expect smaller scale and more frequent disturbances to appear on the cavity, which is supported by Fig. 7(a). This range of \(\dot{\psi }\)/\(\dot{\alpha }\) coincides with one contiguous cavity appearing for each rotation period consistent with type 1 water walking.
Discussion
To extend our knowledge of elastomeric spheres skipping a single time to multi-skip events, spheres of varying sizes and shear moduli G are propelled across a lake surface with a wide range of impact conditions (impact velocity U0 and impact angle β0). These skipping events are captured and quantified using high speed cameras, low speed cameras and image processing; the results are compared with mathematically modeled multi-skip events. For traditional skipping, the model exhibits accurate estimation of impact velocity U0, impact angle β0 and peak acceleration magnitude a. For the representative cases shown, the model provides a reasonable prediction for number of skips N and distance travelled d.
This large-scale experimental effort led to the discovery of a new skipping mode for elastomeric spheres labeled “water walking”, which is characterized by a sphere with comparatively high angular velocity \(\dot{\psi }\) maintaining a constant deformed prolate posture. It also involves the sphere moving nearly parallel to the water surface while the tips of the major axis of the spheroid impact the water surface rapidly. Simulated skipping events with the same initial conditions as water walking predict comparable values for a, U0 and β0, but underestimate N and d. However, the model does predict a transition to similar impact events with very low values of β0, which is characteristic of the transition to water walking.
Water walking occurs when the sphere acquires significant rigid body rotation, which incites a persistent, deformed sphere shape. The amount of rotation necessary varies with sphere shear modulus, radius and density. Experiments have shown this deformed shape to resemble a prolate spheroid, which indicates that the sphere is not just undergoing a rigid body rotation but also has elastic waves propagating within it. The ratio of rigid rotation rate to the angular rate of the elastic waves classifies the type of water walking observed. In type 2 walking, the tips of the spheroid dip below the surface approximately twice per rotation cycle creating two distinct cavities. For type 1 walking, the amplitude of perturbations in the position of the lowest point on the sphere is smaller than for type 2 walking. As a result, the lowest point doesn’t repeatedly rise above the static free-surface level as in the type 2 case. Instead, approximately one contiguous cavity is formed in each rotation cycle, although the cavity surface is wavy due to interactions with the deforming sphere.
Our results show no observed correlation between number of skips N and the distance of the skipping event d (See Appendix B, Supplementary Information). However, water walking events consistently produce values of N that are an order of magnitude higher than traditional skipping events.
Methods
We investigated the water skipping characteristics of deformable elastomeric spheres by creating multi-skip events on a lake surface (Bear Lake, UT, USA). Data were only collected during the early morning or early evening hours when the lake was smooth and waves were minimal (see Fig. 1). We varied sphere impact velocity U0, impact angle β0, diameter D and material shear modulus G. Spheres were made from a platinum-cure silicone rubber called Dragon Skin®, produced by Smooth-On, Inc. Sphere shear modulus G was altered by adding a silicone thinner to the mixture to produce three values (G = 12.3, 28.5 & 74.7 kPa) with a density of \({\rho }_{s}=1070\) kg/m3. The ingredients were measured by mass ratio, then mixed and placed into a vacuum chamber to remove entrained air. The resulting mixtures were poured into aluminum molds to form spheres of two diameters (R = 25.5 & 50 mm). Prior research shows that these spheres can be reasonably modeled as neo-Hookean solids13.
Spheres were launched from a pneumatic cannon at the water surface to initiate skipping, as shown in Fig. 8. Air pressure was varied to control U0 and the barrel angle was adjusted to alter β0. Impact conditions were filmed using a Photron SA3 high speed camera filming at 1000 fps; this footage was used to measure U0 and β0. Downrange footage was captured using several different cameras (Photron SA3, Sony A7R, GoPro and iPhone). This experimental setup on the lakeside is shown in Fig. 8. A six-axis ±200 g accelerometer was embedded within some of the larger spheres (R = 50 mm) to measure acceleration during skipping. The number of times a sphere skips before entry is indicated by N, and was measured from high speed video. The distance from the cannon barrel tip to water entry (end of skipping) is denoted by d, and was measured by eye using markers along the shore.
Additional experiments were conducted in a 0.9 × 1.2 × 27.4 m tank. The skipping events were filmed with a Phantom v310 high speed camera using diffuse backlighting.
Data Availability
The datasets generated and analysed during the current study are available from the corresponding author on reasonable request.
References
Bourne, W. The Arte of Shooting in Great Ordnaunce (Thomas Dawson, 1587).
Douglas, H. A Treatise on Naval Gunnery (J. Murray, 1855).
de Jonquières, E. Sur le ricochet des projectiles sphèriques a la surface de leau. Comptes Rendus de Acadèmie des Sciences 97, 1278–1281 (1883).
Johnson, W. Ricochet of non-spinning projectiles, mainly from water; part i: Some historical contributions. Int. J. Impact. Eng. 21, 15–24 (1998).
Birkhoff, G. et al. Ricochet off water. Applied Mathematics Panel, National Defense Research Committee, Memo 42 (1944).
Hewitt, I., Balmforth, N. & McElwaine, J. Continual skipping on water. J. Fluid. Mech. 669, 328–353 (2011).
Bocquet, L. The physics of stone skipping. Am. J. Phys. 71, 150–155 (2003).
Clanet, C., Hersen, F. & Bocquet, L. Secrets of successful stone-skipping. Nature 427, 29–29 (2004).
Rosellini, L., Hersen, F., Clanet, C. & Bocquet, L. Skipping stones. J. Fluid. Mech. 543, 137–146 (2005).
Nagahiro, S. & Hayakawa, Y. Theoretical and numerical approach to “magic angle” of stone skipping. Phys. Rev. Lett. 94, 174501 (2005).
Truscott, T. T., Wright, M. M., Langley, K. R. & Belden, J. Holy balls! balls that walk on water. Phys. Fluids 24, 091103 (2012).
Belden, J., Jandron, M. A. & Truscott, T. T. Physics of elastic spheres skipping on water. In Sports Physics, 448–459 (Ed. l’Ecole Polytech, Paris, 2012).
Belden, J., Hurd, R. C., Jandron, M. A., Bower, A. F. & Truscott, T. T. Elastic spheres can walk on water. Nat. Commun. 7, 912–930 (2016).
Glasheen, J. W. & McMahon, T. A. A hydrodynamic model of locomotion in the basilisk lizard. Nature 380, 340–342 (1996).
Acknowledgements
R.C.H., J.B. and T.T.T. acknowledge funding from the Office of Naval Research, Navy Undersea Research Program (grant N0001414WX00811), monitored by Ms. Maria Medeiros. J.B., S.H. and M.A.J. acknowledge funding from the Naval Undersea Warfare Center In-House Lab Independent Research program.
Author information
Authors and Affiliations
Contributions
R.H., J.B. & T.T. conceived the experiment(s), R.H., J.B., S.H. & T.T. conducted the experiment(s), R.H., J.B., A.B., M.J. & T.T. analysed the results. All authors reviewed the manuscript.
Corresponding author
Ethics declarations
Competing Interests
The authors declare no competing interests.
Additional information
Publisher’s note: Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Supplementary information
Rights and permissions
Open Access This article is licensed under a Creative Commons Attribution 4.0 International License, which permits use, sharing, adaptation, distribution and reproduction in any medium or format, as long as you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons license, and indicate if changes were made. The images or other third party material in this article are included in the article’s Creative Commons license, unless indicated otherwise in a credit line to the material. If material is not included in the article’s Creative Commons license and your intended use is not permitted by statutory regulation or exceeds the permitted use, you will need to obtain permission directly from the copyright holder. To view a copy of this license, visit http://creativecommons.org/licenses/by/4.0/.
About this article
Cite this article
Hurd, R.C., Belden, J., Bower, A.F. et al. Water walking as a new mode of free surface skipping. Sci Rep 9, 6042 (2019). https://doi.org/10.1038/s41598-019-42453-x
Received:
Accepted:
Published:
DOI: https://doi.org/10.1038/s41598-019-42453-x
Comments
By submitting a comment you agree to abide by our Terms and Community Guidelines. If you find something abusive or that does not comply with our terms or guidelines please flag it as inappropriate.