Abstract
A single-cycle laser pulse was generated using a two-stage compressor and characterized using a pulse characterization technique based on tunnelling ionization. A 25-fs, 800-nm laser pulse was compressed to 5.5 fs using a gas-filled hollow-core fibre and a set of chirped mirrors. The laser pulse was further compressed, down to the single-cycle limit by propagation through multiple fused-silica plates and another set of chirped mirrors. The two-stage compressor mitigates the development of higher-order dispersion during spectral broadening. Thus, a single-cycle pulse was generated by compensating the second-order dispersion using chirped mirrors. The duration of the single-cycle pulse was 2.5 fs, while its transform-limited duration was 2.2 fs. A continuum extreme ultraviolet spectrum was obtained through high-harmonic generation without applying any temporal gating technique. The continuum spectrum was shown to have a strong dependence on the carrier-envelope phase of the laser pulse, confirming the generation of a single-cycle pulse.
Similar content being viewed by others
Introduction
Ultrashort laser pulses have become essential tools for studying ultrafast light-matter interactions1,2,3,4,5. The duration of the laser pulse is a key parameter for controlling strong-field processes, such as above-threshold ionization (ATI)6, high-harmonic generation (HHG)7, and frustrated tunnelling ionization (FTI)8. Tunnelling ionization, occurring every half optical cycle of the laser pulse, is the first step of those processes. In order to control the number of ionization events in such experiments, it is important to reduce the number of cycles in the pulse. The temporal confinement of the ionization allows a precise time-resolved measurement of light-matter interactions9. It also enables the generation of an isolated attosecond pulse through HHG10. Consequently, an efficient method for the generation and characterization of a single-cycle laser pulse is needed for the study and application of ultrafast optical science.
Tremendous efforts have been made to reduce the duration of a laser pulse down to a few cycles or to the single-cycle regime1,11,12,13,14. Obtaining such an ultrashort laser pulse requires spectral broadening and phase control over the spectrum. Hollow-core fibres have been widely used for spectral broadening of milli-joule laser pulses15,16,17,18,19,20,21. The spectrum of the laser pulse is broadened due to nonlinear interactions, such as the optical Kerr effect or ionization in a gas-filled hollow-core fibre. The output pulse from these fibres can have a spectrum broad enough to generate a single-cycle pulse; however, complicated phase structure develops during propagation in the nonlinear optical media. The laser pulse can be compressed down to the limit of only a few cycles when the second-order dispersion is compensated using chirped mirrors15,16. In order to further compress the pulse, third- and higher-order dispersion must be compensated using a higher-order chirped mirror22,23, material dispersion24,25, or pulse synthesizer11,12.
Spectral broadening of a laser pulse can also be achieved in a solid material. A solid material is vulnerable to optical damage due to self-focusing of a laser pulse26,27,28,29,30. Kung et al. avoided this self-focusing problem by using multiple thin glass plates. The multiple glass plates were arranged near the focus so that the self-focusing of the laser beam was balanced by the divergence of the laser beam. In this way, it was possible to compress the laser pulse down to the few-cycle limit when the second-order dispersion is compensated.
In this report, we present a two-stage compressor developed for the generation of a single-cycle laser pulse. The two-stage compressor consists of a hollow-core fibre and multiple thin glass plates; the spectrum of a laser pulse is broadened due to the Kerr effect in both cases, which universally occurs for all wavelengths. The arrangement of the two-stage compressor offers sufficient spectral broadening for the generation of a single-cycle laser pulse. It is more efficient than a two-stage compressor that uses two hollow-core fibres31, because the second stage of compression using multiple plates is insensitive to the alignment of the laser beam. Our measurements show that the development of higher-order dispersion is suppressed in the two-stage compressor, and single-cycle laser pulses can be generated by compensating the second-order phase with chirped mirrors. The temporal characterization of the single-cycle laser pulse was performed using the tunnelling ionization with perturbation for the time-domain observation of an electric field (TIPTOE) method32.
Results
Limitation of single-stage compression
The experimental setup for the two-stage compression is shown in Fig. 1. In order to determine the optimal pressure of the hollow-core fibre to minimize the pulse duration, the temporal profiles of the compressed laser pulse were measured using the TIPTOE method at various gas pressures. Once the pressure in the hollow fibre was set to a certain value, the temporal profiles were measured while adjusting the thickness of the glass wedge to find the shortest pulse duration. The shortest pulse duration (blue line) for different pressures are shown alongside their transform-limited pulse duration (red line) in Fig. 2(a). Since the spectral broadening increased with Ne pressure, the transform-limited pulse duration τTL gradually decreases with pressure up to 3400 torr. The actual pulse duration τ, however, decreases with pressure only up to 3000 torr, and the duration increases at pressures above 3000 torr. The compressibility of the fibre is defined as the ratio of the two durations (τ/τTL), and its dependence on Ne pressure is shown in Fig. 2(b). Since the second-order phase of the laser pulse can be compensated using a set of chirped mirrors and a glass wedge, the increase of the compressibility indicates that a significant amount of higher-order dispersion of the pulse exists at high pressure.
The amount of the spectral broadening increases with the Ne pressure in the fibre, but there is a limit to the resulting reduction in the pulse duration. The temporal profiles of the laser pulses obtained at 3000 torr and 3400 torr are compared in Fig. 2(c,d). While the spectral phase is almost flat at 3000 torr (Fig. 2(e)), the spectral phase obtained at 3400 torr shows that the third-order phase developed during the nonlinear propagation in the fibre (Fig. 2(f)). In the time domain, the residual higher-order dispersion caused the formation of satellite pulses near the main pulse, as shown in Fig. 2(d). Thus, if the higher-order dispersion is not suppressed, the shortest duration that can be achieved using a single-stage compressor is limited.
Theoretical calculation for a second pulse compressor
The propagation of the laser beam through the multiple fused-silica plates in space and time was numerically solved near the multiple glass plates as illustrated in Fig. 3(a). The peak intensity of the laser beam is 2 × 1013 W/cm2 just before the first glass plate. Without the glass plates, the laser beam should have been focused at z = 8 cm. However, the laser beam was focused at z = 5 cm due to the self-focusing effect as shown in Fig. 3(b). The laser beam diverges after the first focus (z = 5 cm); it is focused again at the second focus (z = 9.6 cm), after propagation through the second glass plate, and it diverges again. After the propagation through the third plate, the laser beam diverges up to the far field. Then, it is assumed that the laser beam is refocused at the point ‘f’ in Fig. 3(a). The temporal profile and spectrum of the laser pulse are calculated at the point ‘f’. The spectrum is broadened (Fig. 3(c,d)). The duration of the laser pulse was estimated after compensating the second-order phase of the pulse as 2.22 fs (Fig. 3(e,f)), while the transform-limited duration is 2.19 fs. This numerical calculation shows that the higher-order phase is not much developed during the propagation through the multiple glass plates. In addition, the laser beam is very little distorted during the nonlinear propagation in the second compressor as shown in Fig. 3(c,e). Thus, a single-cycle pulse can be efficiently generated using our two-stage compressor.
Generation of a single-cycle pulse using a two-stage compressor
A two-stage compressor was implemented experimentally. In order to compress the few-cycle laser pulse obtained from the hollow-core fibre to the single-cycle limit, multiple fused-silica plates were employed at the second stage of the compressor, as shown in Fig. 1. The input energy before the multiple glass plates was 120 μJ while the output energy was 90 μJ, which indicates a transmittance of 75%. The beam shape measured at the far field after the second compressor is shown in Fig. 3(g). According to the theoretical calculations shown in Fig. 3, we expect the duration to be near to that of a single cycle. Since conventional temporal characterization techniques rely on second-harmonic generation, it is difficult to measure the single-cycle pulse duration due to the limited bandwidth of a nonlinear crystal. Here, we employ a new temporal characterization technique called TIPTOE, in which a sub-cycle ionization event is used as a fast temporal gate to sample an additional weak field32. Since the technique can be applied over a broad wavelength range, it is an ideal tool for the temporal characterization of ultrashort laser pulses.
In the TIPTOE method, the laser pulse is divided into two pulses with different intensities to form a strong pulse that tunnel-ionizes air molecules and a weak pulse superposed with the strong pulse. The modulation of the ionization yield, measured as a function of the time delay between the two pulses, represents the temporal profile of the electric field of the weak pulse. The temporal profile of the electric field, obtained from the modulation of the ionization yield, is shown in Fig. 4(a). The central wavelength of the main pulse is 650 nm (for which wavelength, 1 optical cycle is 2.17 fs). The duration of the main pulse is 2.5 fs as shown in Fig. 4(b) which corresponds to 1.15 optical cycle at 650 nm. The main pulse contains 51% energy. Although the growth of pre-pulses is not observed in the theoretical calculations shown in Fig. 3, the pre-pulses become more prominent after the second compressor in the experiment. The existence of the pre-pulse would be a serious problem for some applications; however, applications like HHG would not be much affected by such structure since the amount of ionization caused by the pre-pulses is not significant when compared to that of the main pulse. The spectral amplitude and phase of the laser pulse after the second compressor (blue lines in Fig. 4(c)) were obtained by taking the Fourier transform of the temporal laser field. The spectrum retrieved in this way agrees well with the experimentally measured spectrum (red line), supporting the validity of the TIPTOE measurement.
High harmonic generation with a single-cycle laser pulse
An intense single-cycle laser pulse can confine an ionization event within a half cycle at the peak of the laser pulse, which can be used for the generation of an isolated attosecond pulse11. To see the effect of a single ionization event, we performed a HHG experiment using the single-cycle pulses obtained from the two-stage compressor. The central part of the laser beam with 45 μJ of energy was focused onto an argon gas target using a focusing mirror with a 10-cm focal length. We controlled the dispersion and carrier-envelope phase (CEP) of the single-cycle pulses using a pair of glass wedges. High-harmonic spectra were recorded for different thicknesses of the glass wedge. The high harmonic spectra are continuous, as shown in Fig. 5. The amplitude values of the harmonic spectra were greatly modulated as the CEP of the laser pulse changed, a typical feature of harmonic spectra obtained with single-cycle laser pulses. These measurements confirm the generation of single-cycle pulses.
Discussion
We demonstrated a method for generating and characterizing single-cycle laser pulses. Single-cycle laser pulses were obtained using a two-stage compressor consisting of a hollow-core fibre and subsequent multiple fused-silica plates. Temporal characterization was achieved by applying the TIPTOE method. It was found that the two-stage compressor mitigated the development of higher-order dispersion, making compensation of higher-order dispersion unnecessary. The initial laser pulse duration of 25 fs was compressed down to 2.5 fs, as expected from numerical calculations. The continuum harmonic spectrum exhibited strong dependence on the CEP of laser pulses, supporting our characterization of the single-cycle laser pulse via the TIPTOE method. The ultrashort laser pulse will be an important tool for studying time-resolved phenomena. In addition, it will be used as a versatile tool for controlling the strong-field processes such as ATI, HHG, and FTI.
Methods
A carrier-envelope-phase-stabilized 25-fs pulse at 800 nm from a titanium sapphire laser (Femtolasers, Femtopower X CEP) was used to perform all experiments. The laser beam was focused (f-number = 222) into the first compressor which is consists of a stretched hollow-core fibre (500-μm inner diameter), chirped mirrors (Ultrafast innovation, HD PC37_4) and glass wedges (Femtolasers, BK7, 8°) as shown in Fig. 1. The entrance side of the fibre was connected to a vacuum pump, while the other side was filled with Ne gas to maintain a pressure gradient in the fibre. The pressure of the fibre was stabilized by the pressure controller (Alicat, PC-100PSI-D). The input energy of the hollow-core fibre was 1.2 mJ while the output energy was 0.8 mJ after the fiber, showing a transmittance of 67%. Due to the long distance between the first and the second compressor (~10 m) and the thick glass wedge, 32 chirped mirrors (16 pairs) are used. The energy of the laser beam was measured as 320 μJ after the chirped mirror and glass wedges. The iris was placed at the entrance of second stage compressor to get the optimal peak intensity of laser. The laser from the first compressor was focused using a 1.5 m focal length mirror into the second compressor. Three fused silica plates (50, 50, and 100 µm) were placed at Brewster’s angle in a vacuum chamber. The output energy was measured as 90 μJ, showing the transmittance of 75%. Most of loss was caused by the glass windows of the vacuum chamber which was placed perpendicularly with respect to the incident light direction. 16 chirped mirrors (Ultrafast innovation, HD PC37_4) are used after the second compressor. The spectra of the laser pulses shown in Figs 2 and 4 were measured by a grating-based spectrometer (Ocean optics, USB4000). The CEP of the single-cycle pulse was controlled by a glass wedge (Femtolasers, Fused silica, 2°48′) for HHG experiment. High harmonic spectra were measured using a chevron MCP imaging detector (Photonis) and a CMOS camera (PCO, Edge).
In order to study the propagation of a laser pulse in a second pulse compressor, the nonlinear propagation of the laser pulse through multiple fused-silica plates and vacuum spaces was analysed by solving the nonlinear pulse propagation equation in three dimensions (using Eq. 119 in ref.33). In the calculation, a nonlinear index n2 of 3 × 10−16 cm2/W was used for the description of the Kerr effect in the medium. The nonlinear absorption coefficient for the multiphoton absorption was adjusted to give the absorption value (5%) observed in the experiment. Experimental parameters, including pulse intensity, beam size at the focus (200 μm), and the separation of the glass plates (8 and 7 cm), are used in the calculation. Since cylindrical symmetry along the propagation axis (z axis in Fig. 3) is assumed, the glass plates were orthogonal to the propagation direction in the calculation model, while they are placed at Brewster’s angle in the experiment; therefore, the thickness of the glass was increased by 20% for the three plates (60, 60, and 120 μm) in the calculation to compensate for the angle difference. Since all parameters for the calculation were chosen to be as close as possible to those of the experimental conditions, the propagation of the laser pulse in the multiple glass plates could be accurately modelled.
References
Brabec, T. & Krausz, F. Intense few-cycle laser fields: Frontiers of nonlinear optics. Rev. Mod. Phys. 72, 545–591 (2000).
Dudovich, N. et al. Measuring and controlling the birth of attosecond XUV pulses. Nat. Phys. 2, 781–786 (2006).
Corkum, P. B. & Krausz, F. Attosecond science. Nat. Phys. 3, 381–387 (2007).
Goulielmakis, E. et al. Single-Cycle Nonlinear Optics. Science 320, 1614–1617 (2008).
Rybka, T. et al. Sub-cycle optical phase control of nanotunnelling in the single-electron regime. Nat. Photonics 10, 667–670 (2016).
Agostini, P., Fabre, F., Mainfray, G., Petite, G. & Rahman, N. K. Free-Free Transitions Following Six-Photon Ionization of Xenon Atoms. Phys. Rev. Lett. 42, 1127–1130 (1979).
Corkum, P. B. Plasma perspective on strong field multiphoton ionization. Phys. Rev. Lett. 71, 1994–1997 (1993).
Nubbemeyer, T., Gorling, K., Saenz, A., Eichmann, U. & Sandner, W. Strong-Field Tunneling without Ionization. Phys. Rev. Lett. 101, 233001 (2008).
Milošević, D. B., Paulus, G. G., Bauer, D. & Becker, W. Above-threshold ionization by few-cycle pulses. J. Phys. B At. Mol. Opt. Phys. 39, R203–R262 (2006).
Sansone, G. et al. Isolated Single-Cycle Attosecond Pulses. Science 314, 443–446 (2006).
Hassan, M. T. et al. Optical attosecond pulses and tracking the nonlinear response of bound electrons. Nature 530, 66–70 (2016).
Krauss, G. et al. Synthesis of a single cycle of light with compact erbium-doped fibre technology. Nat. Photonics 4, 33–36 (2010).
Balciunas, T. et al. A strong-field driver in the single-cycle regime based on self-compression in a kagome fibre. Nat. Commun. 6, 6117 (2015).
Krogen, P. et al. Generation and multi-octave shaping of mid-infrared intense single-cycle pulses. Nat. Photonics 11, 222–226 (2017).
Nisoli, M. et al. Compression of high-energy laser pulses below 5 fs. Opt. Lett. 22, 522 (1997).
Vozzi, C., Nisoli, M., Sansone, G., Stagira, S. & De Silvestri, S. Optimal spectral broadening in hollow-fiber compressor systems. Appl. Phys. B 80, 285–289 (2005).
Sung, J. H., Park, J. Y., Imran, T., Lee, Y. S. & Nam, C. H. Generation of 0.2-TW 5.5-fs optical pulses at 1 kHz using a differentially pumped hollow-fiber chirped-mirror compressor. Appl. Phys. B 82, 5–8 (2006).
Chen, X. et al. Generation of 4.3 fs, 1 mJ laser pulses via compression of circularly polarized pulses in a gas-filled hollow-core fiber. Opt. Lett. 34, 1588–1590 (2009).
Schmidt, B. E. et al. CEP stable 1.6 cycle laser pulses at 1.8 μm. Opt. Express 19, 6858–6864 (2011).
Hädrich, S. et al. Nonlinear compression to sub-30-fs, 0.5 mJ pulses at 135 W of average power. Opt. Lett. 38, 3866–3869 (2013).
Oishi, Y., Suda, A., Midorikawa, K. & Kannari, F. Sub-10 fs, multimillijoule laser system. Rev. Sci. Instrum. 76, 093114 (2005).
Bohman, S., Suda, A., Kanai, T., Yamaguchi, S. & Midorikawa, K. Generation of 5.0 fs, 5.0 mJ pulses at 1 kHz using hollow-fiber pulse compression. Opt. Lett. 35, 1887–1889 (2010).
Cavalieri, A. L. et al. Intense 1.5-cycle near infrared laser waveforms and their use for the generation of ultra-broadband soft-x-ray harmonic continua. New J. Phys. 9, 242 (2007).
Silva, F. et al. Simultaneous compression, characterization and phase stabilization of GW-level 1.4 cycle VIS-NIR femtosecond pulses using a single dispersion-scan setup. Opt. Express 22, 10181–10191 (2014).
Timmers, H. et al. Generating high-contrast, near single-cycle waveforms with third-order dispersion compensation. Opt. Lett. 42, 811–814 (2017).
Lu, C.-H. et al. Generation of intense supercontinuum in condensed media. Optica 1, 400–406 (2014).
Cheng, Y.-C., Lu, C.-H., Lin, Y.-Y. & Kung, A. H. Supercontinuum generation in a multi-plate medium. Opt. Express 24, 7224–7231 (2016).
He, P. et al. High-efficiency supercontinuum generation in solid thin plates at 0.1 TW level. Opt. Lett. 42, 474–477 (2017).
Huang, P.-C. et al. Polarization control of isolated high-harmonic pulses. Nat. Photonics 12, 349–354 (2018).
Lu, C.-H. et al. Sub-4 fs laser pulses at high average power and high repetition rate from an all-solid-state setup. Opt. Express 26, 8941 (2018).
Mak, K. F. et al. Compressing J-level pulses from 250 fs to sub-10 fs at 38-MHz repetition rate using two gas-filled hollow-core photonic crystal fiber stages. Opt. Lett. 40, 1238–1241 (2015).
Park, S. B. et al. Direct sampling of a light wave in air. Optica 5, 402–408 (2018).
Couairon, A. et al. Practitioner’s guide to laser pulse propagation models and simulation. Eur. Phys. J. Spec. Top. 199, 5–76 (2011).
Acknowledgements
The authors appreciate W.T. Ra’s technical support. Institute for Basic Science (IBS-R012-D1).
Author information
Authors and Affiliations
Contributions
S.I.H. and K.T.K. designed the study and performed the theoretical analysis; S.I.H. performed the pulse compression experiment; S.I.H., S.B.P. and W.C. performed the pulse measurement and the HHG experiment; J.H.M. analysed the HHG spectrum; S.I.H., C.H.N. and K.T.K. wrote the manuscript; and all authors discussed the results and interpretations.
Corresponding author
Ethics declarations
Competing Interests
The authors declare no competing interests.
Additional information
Publisher’s note: Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Rights and permissions
Open Access This article is licensed under a Creative Commons Attribution 4.0 International License, which permits use, sharing, adaptation, distribution and reproduction in any medium or format, as long as you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons license, and indicate if changes were made. The images or other third party material in this article are included in the article’s Creative Commons license, unless indicated otherwise in a credit line to the material. If material is not included in the article’s Creative Commons license and your intended use is not permitted by statutory regulation or exceeds the permitted use, you will need to obtain permission directly from the copyright holder. To view a copy of this license, visit http://creativecommons.org/licenses/by/4.0/.
About this article
Cite this article
Hwang, S.I., Park, S.B., Mun, J. et al. Generation of a single-cycle pulse using a two-stage compressor and its temporal characterization using a tunnelling ionization method. Sci Rep 9, 1613 (2019). https://doi.org/10.1038/s41598-018-38220-z
Received:
Accepted:
Published:
DOI: https://doi.org/10.1038/s41598-018-38220-z
This article is cited by
-
Simulating an ultra-broadband concept for Exawatt-class lasers
Scientific Reports (2021)
-
Reconstruction algorithm for tunneling ionization with a perturbation for the time-domain observation of an electric-field
Scientific Reports (2021)
-
Coherent electron displacement for quantum information processing using attosecond single cycle pulses
Scientific Reports (2020)
-
Temporal characterization of femtosecond laser pulses using tunneling ionization in the UV, visible, and mid-IR ranges
Scientific Reports (2019)
Comments
By submitting a comment you agree to abide by our Terms and Community Guidelines. If you find something abusive or that does not comply with our terms or guidelines please flag it as inappropriate.