Abstract
The dielectric-semiconductor-dielectric-metal 4 layered structure is a well-established configuration to support TM hybrid plasmonic modes, which have demonstrated significant advantages over pure photonic modes in structures without metal to achieve low loss resonant cavities at sub-diffraction limited volumes. The photonic modes with TE characteristics supported by the same 4 layered structure, on the other hand, are less studied. Here we show that a low loss photonic mode with TE01 characteristics exists in the dielectric-semiconductor-dielectric-metal 4 layered structure if a truncated cylindrical disk is chosen as the semiconductor core. This mode exhibits the lowest cavity loss among all resonant modes, including both pure photonic and hybrid plasmonic modes, at cavity radius <150 nm and within the wavelength range 620 nm to 685 nm, with a footprint ~0.83 (λ/2neff)2, physical size ~0.47 (λ/2neff)3 and a mode volume down to 0.3 (λ/2neff)3. The low cavity loss of this TE01 mode is attributed to its substantially reduced radiation loss to the far field by the creation of image charges through the metal response. Because of the low mode penetration in the metal, this photonic mode show equally low cavity loss near industry relevant metals such as Cu. Our study demonstrates an alternative to hybrid plamonic modes and metallo-dielectric modes to achieve low loss cavities with extremely small footprints.
Similar content being viewed by others
Introduction
Photonic lasers are one of the key components in integrated photonic circuits1. High integration densities of lasers on a chip will be needed for intra-chip communications. By increasing the refractive index of the lasing materials, the footprint of the photonic lasers can be decreased. However, due to the radiative nature of the dipole mode, pure photonic lasers cannot maintain an effective feedback as the dimension of the cavity gets close to (λ/2neff)3 2. As a result, conventional optical cavities can hardly achieve lasing at dimensions around (λ/2neff)3. To overcome this limitation, metal coated photonic cavities, termed metallo-dielectric cavities, have been exploited to confine light into a diffraction limited volume of (λ/2neff)3 3,4,5,6,7.
Alternatively, people have been looking into hybrid plasmonic modes, which exist at the dielectric-semiconductor-dielectric-metal interface, to achieve lasing at deep subwavelength scale with low propagation loss, promising substantial increase in packing density of optical components in integrated circuits. Since the first experimental observation of hybrid plasmonic lasers by Oulton et al.8, progress has been made to demonstrate greater mode confinement down to 0.2(λ/2neff)3 in the wavelength range of 370 nm to 685 nm and of 1340 nm in the Infrared9,10,11,12,13,14,15. Nevertheless, the extreme mode confinement offered by hybrid plasmonic modes is mostly achieved in 1D or 2D. As a result, the footprint of this type of laser is usually larger than (λ/2neff)2. Different from the well-studied hybrid plasmonic mode, which has mostly transverse magnetic (TM) characteristics, the photonic mode that co-exists in this type of structure, which has transverse electric (TE) characteristics, on the other hand, has received little attention, other than being used as the comparison to the hybrid plasmonic mode to show that the effective refractive index in the photonic case is lower than that in the hybrid plasmonic mode12.
In this report, we focus our attention on the photonic mode that exists in the dielectric-semiconductor-dielectric-metal 4-layered structure and demonstrate how this photonic mode can be used to achieve low loss, sub-diffraction nanocavities with very small footprints.
Results
Analytical model of Fundamental TE mode in a 4-layered planar structure
To understand this photonic mode, we first seek solutions to the Helmholtz equation \({\nabla }^{2}{\bf{E}}+\frac{{\omega }^{2}\varepsilon }{{c}^{2}}{\bf{E}}=0\) in a 4 layered planar structure of dielectric-semiconductor-dielectric-metal, as shown in Fig. 1a. We define that the light propagates in x direction only and there is no spatial variation in the y direction. The z axis is perpendicular to the interface of different media. In this configuration, both TE and TM optical modes exist. The TM mode in this structure can be considered as the hybridization of the guided photonic TM mode in the top three layers with the TM plasmonic mode at the interface of the bottom two layers. This TM mode is commonly called a hybrid plasmonic mode as its dispersion curve closely resembles that of the surface plasmonic propagation at a single dielectric-metal interface16 (also shown later in Fig. 1c).
To obtain the TE mode solution, we solve the Helmholtz equation in these 4 different regions separately and require the solution to satisfy the continuity of Ey and Hx at the interfaces. To simplify our calculations, we choose the refractive index of the dielectrics to be the same ndielectric1 = ndielectric2 = nd. It is well known that the single dielectric-metal interface does not support a TE mode17. In the 4 layered structure with a higher refractive index of semiconductor core layer, however, the continuity boundary conditions at the dielectric-metal interface can be satisfied. If we choose z = 0 at the middle of the semiconductor layer and let d = 2a (Fig. 1a), the solution of the fundamental TE mode in this planar structure can be written as (see Supplementary Information 1 for the Hz components):
Here \({k}_{i}^{2}={\beta }^{2}-\frac{{\omega }^{2}{\varepsilon }_{i}}{{c}^{2}}\) (i = d, m) and \({k}_{c}^{2}=\frac{{\omega }^{2}{\varepsilon }_{c}}{{c}^{2}}-\,{\beta }^{2}\). β is the propagation constant and \({\varepsilon }_{j}\) (j = d, c, m) is the relative permittivity of the dielectric, semiconductor core and metallic substrate, respectively. Bt, A, Bb1, Bb2 and C are coefficients related to the amplitude of the mode in four regions and θ is a parameter describing how far away the maximum of electric field is off the center of the semiconductor core layer due to the presence of bottom metallic layer. The continuity of Ey and Hx at three interfaces leads to:
and
These 6 equations result in the dispersion relationship of this TE mode:
The solution to Eq. (7) can be obtained numerically via the Newton-Raphson method. As a proof of concept, we calculate the dispersion curve of this TE mode from Eq. (7) with a chosen set of parameters and compare the results with those directly obtained from COMSOL multiphysics simulation package (see Methods for details), as shown in Fig. 1b. To simplify the numerical calculation from Eq. (7), all dielectric materials and metal are treated lossless in Fig. 1b. The dispersion curves obtained from these two methods agree very well, with a discrepancy of less than 5% in all frequencies shown in the plot. The obtained angle θ is also plotted in the same panel as a function of β. From the plot, we can also see that at lower frequencies (longer wavelengths), θ > 0 and the center of the photonic mode is pushed slightly away from the center of the semiconductor core layer and in the direction away from the metal substrate. This leads to a decrease in the effective refractive index of the TE mode in the 4-layered structure compared to that of a typical guided photonic TE mode in dielectric-semiconductor-dielectric 3-layered structure.
As a comparison to other optical modes, a set of simulated dispersion curves of the 3-layered photonic TE mode, 4-layered TE mode and 4-layered TM mode (hybrid plasmonic mode) are shown in Fig. 1c (see Supplementary Information 2,3 for details). It is clear from Fig. 1c that the 4-layered TE mode gives the lowest effective refractive index among these three at a given frequency especially in the low frequency region, consistent with the results previously reported on this TE mode12.
For real materials, \({\varepsilon }_{j}\) (j = d, c, m) are all complex numbers, resulting in β complex in the solution to Eq. (7). To evaluate the influence of the losses in materials to the dispersion relationship of the TE mode, we simulate the dispersion curve in this 4-layered TE mode using realistic material parameters of GaInP, from ref.18 as the semiconductor core layer, Ag (\({\varepsilon }_{Ag}={\varepsilon }_{\infty }-\,\frac{{\omega }_{p}^{2}}{{\omega }^{2}+i\gamma \omega }\), where \({\varepsilon }_{\infty }=5\,\,\)and γ = 0.04 eV)8, Al2O3 ultrathin layer of 6 nm (\({\varepsilon }_{A{l}_{2}{O}_{3}}=2.9\)) as the dielectric layer between GaInP and Ag, and Air (\({\varepsilon }_{Air}=1\)) as the top dielectric layer. As a comparison, the TM mode supported by the same 4 layered planar structure is also simulated and plotted together in Fig. 1d. Figure 1d shows that the dispersion curves of TE and TM modes follow a very similar trend as those in Fig. 1c (without losses) in general, but are modulated by the change in refractive index of GaInP at higher frequencies. The imaginary part of the propagation constant β indicates the overall losses of the modes, which is due to the absorption of GaInP and ohmic loss of the metal.
TE01 and TM11 modes in a trancated cylindrical cavity near metal
Interesting results appear when we use the 4-layered structure to form nanocavities. In the following simulations, we keep the metal substrate (Ag) optically thick and laterally large and shrink the lateral dimension of the semiconductor layer to form a truncated cylindrical disk shaped cavity (Fig. 2a). In this design, the top dielectric layer is air and the bottom dielectric layer is Al2O3 of a thickness of 6 nm, same as the values used in Fig. 1d. The thickness of the semiconductor layer is kept at 110 nm and the semiconductor material is chosen to be the quaternary AlGaInP as used in ref.13. As a comparison, we also investigate pure photonic cavities of same semiconductor core dimensions, as shown in Fig. 2b. Similar to Fig. 1d, simulations below use realistic material parameters, as used in refs8,13. If we look for resonant modes in a fixed range of wavelengths, for example 620 nm to 685 nm for the active region of quaternary AlGaInP, we found previously that for cavities of diameter larger than 1 µm, the Q of the pure photonic cavities is much higher than that of the cavities near metal. As the diameter of the cavity decreases below the wavelength of the corresponding cavity mode, the cavity loss in the photonic cavity increases rapidly due to the loss of mode confinement and more importantly the increase of radiation loss19. On the other hand, because of the higher effective refractive index offered by the hybrid plasmonic modes, the higher order (≥3) whisper gallery resonant modes of hybrid plasmonic characteristics are the least lossy for cavities of diameter between 300 nm and 650 nm13. For cavities below the diameter of 300 nm, the whispering gallery resonant mode number drops below 3. As a result, the mode confinement starts to deteriorate (effective refractive index neff drops below 1.7) and total internal reflection is no longer satisfied. Consequently, the quality factor Q of the hybrid plasmonic resonant modes decreases rapidly13.
At very small cavity diameters, namely from 190 nm to 240 nm, a low loss resonant TE mode in the 4 layered structure starts to emerge in the wavelength range of 620 nm to 685 nm. Solving the Helmholtz equation in cylindrical coordinates (ρ, φ, z) reveals that this TE resonant mode can be described by the fundamental TE01 mode, which is also called a magnetic dipole mode5,6. (see Methods for details) Its Hz component within the semiconductor core can be approximated by a Bessel function ~J0(kρcρ) and Eφ component ~J1(kρcρ), while the Hz component outside the semiconductor core can be mostly approximated by the modified Bessel function of second kind ~K0(kρdρ) and Eφ component ~K1(kρdρ). Here kρc and kρd are determined by permittivities of the semiconductor core and outer dielectric material. (see Methods for details) This TE01 mode distribution mimics a classical circular electric current (the donut shape in Fig. 2c) inducing a vertical magnetic field (Fig. 2g).
Without the metal substrate, this TE01 mode is of radiative nature (Fig. 2c–g). As the length scale of the cavity approaches λ/2neff, the cavity becomes a good antenna. If we consider the cavity losses as the sum of internal losses (due to the absorption of semiconductor disk) and radiation loss20, the latter dominates for the semiconductor disk with diameter >200 nm. Figure 2d shows the Ex distribution on xy plane with z at 45 nm into glass substrate for a semiconductor disk of 200 nm in diameter on glass. The radiation pattern from the disk is clearly visible from the plot. The leak of energy into the glass substrate is also observable in Fig. 2f. This radiation loss places a fundamental limit to the quality factor of the TE01 mode in a pure photonic cavity.
With the semiconductor disk placed on top of a metal substrate, the metal responds to electromagnetic oscillations in the cavity by generating image charges at the interface. The image charges create an opposing electric field in the cavity. An opposite magnetic field, as illustrated in Fig. 3a, is also generated. Consequently, the radiation of this magnetic dipole mode to the far field is strongly suppressed due to its image magnetic dipole (in opposite direction). This is evident in Fig. 2h,i, where the electric field shows little distribution outside the semiconductor core. We therefore call this TE01 mode a ‘dark’ magnetic dipole mode. We also calculate the footprint, physical size and effective mode volume13 of the TE01 mode as shown in Fig. 2h–l, which are 0.83(λ/2neff)2, 0.47(λ/2neff)3 and 0.3(λ/2neff)3 respectively. The TM11 resonant mode in this structure, on the other hand, shows much higher cavity loss due to the enhanced radiation, as illustrated in Fig. 3b, where the vertical component of electric field induces an imaging electric field of the same direction. As a result, an effective lying down magnetic dipole is induced. This mode is similar to the electric dipole induced magnetic dipole mode observed on silicon nanocavities when placed on top of a metallic mirror21,22. The enhanced radiation loss is also evident in the field distribution plots of Fig. 2m–q. The electric field spills out of the physical dimension of the semiconductor core (Fig. 2m) and radiates out to the far field (Fig. 2p).
Discussion
Figure 3 compares the simulated resonant wavelengths (Fig. 3c) of the TE01 mode on glass, on Al2O3/Ag, on Al2O3/Cu and the TM11 mode on Al2O3/Ag as well as their corresponding quality factors Q (Fig. 3d) as a function of the disk diameter. It is clear from the plots that the TE01 mode supported by disks on glass shows the highest effective refractive index compared to that of the TE01 modes supported by disks on Al2O3/Ag or Al2O3/Cu, at a given diameter, consistent with the conclusion we obtain from the planar structures in Fig. 1. Nevertheless, the quality factors Q of the TE01 modes near metal are substantially higher compared to that of its counterpart on glass. Notably, because this TE01 ‘dark’ magnetic dipole mode has photonic characteristics and the mode overlap with the metal is very small, the requirement for ‘good’ plasmonic metals, such as Ag and Au, to maintain its low cavity loss and mode confinement is relaxed. As shown in Fig. 3d, the quality factor Q of TE01 mode on industry relevant metal Cu23 is comparable with that on Ag. Analytical models to estimate the resonant wavelength of TE01 mode on glass, that on Al2O3/Ag and on Al2O3/Cu as well as their corresponding quality factor Q, taking into account both the radiation loss of the magnetic dipole and internal losses of metal and semiconductor, as a function of disk diameter are proposed and detailed in the Methods. Fittings of simulated TE01 resonant wavelengths to the analytical models are given in Fig. 3c as solid curves. Plugging the fitted parameters to the analytical loss model yields the quality factor Q of TE01 modes on various substrates, indicated by the dashed curves in Fig. 3d. It is understood from the analytical models that for semiconductor disks of diameter ≥250 nm, the radiation loss dominates in the TE01 cavity loss while for diameter <200 nm, the internal losses of the cavity prevail. The simulated Q by COMSOL package shows a similar trend. We also find that increasing the Al2O3 spacer layer thickness slightly decreases the Q of the TE01 mode, which can be understood as the increase of distance between the magnetic dipole and its image dipole leading to inefficient suppression of the radiation loss to the far field. (see Supplementary Figure S3).
The TM11 mode on Al2O3/Ag, on the other hand, demonstrates strong hybridization between the photonic mode and surface plasmonic mode, resulting in much higher effective refractive index compared to that of TE01 mode on glass or near metal (Fig. 3c). However, the enhanced radiation loss in the TM11 mode near metal also results in higher cavity loss therefore much lower cavity quality factor Q in the full diameter range of Fig. 3d compared to that of TE01 mode on Al2O3/Ag. Consequently, the TE01 ‘dark’ magnetic dipole mode becomes more advantageous over the hybrid plasmonic TM11 mode or the photonic TE01 magnetic dipole mode as the diameter of the cavity decreases below 250 nm.
The lowest quality factor Q of cavities that achieved lasing at room temperature using similar materials as discussed here is ∼79, with an oval-shaped 350 nm × 390 nm quaternary AlGaInP disk on Al2O3/Ag13. The simulated Q of TE01 modes (within the wavelength range of 620 nm to 685 nm) on Ag and Cu varies from 24 to 29, which is difficult to achieve lasing at room temperature. Nevertheless, Lu et al. have reported hybrid plasmonic lasers achieved at 120 K with cavity Q-factor of ∼13 in the wavelength range of 470 nm to 640 nm10,11. It is therefore reasonable to assume that at low temperature, for example 120 K, where the resistive heating in metal is greatly reduced6, and with better metal preparation10, lasing from the TE01 ‘dark’ magnetic dipole mode can be expected. It needs to be noted that the technical advantage of the 4-layered structure lies in the fewer processing steps compared to the steps required for the top and bottom capped metal-clad structures. If the extreme footprint is the ultimate goal of the cavity design, the metal-clad metal–insulator–semiconductor mode can be a better option6,24,25.
In conclusion, we theoretically demonstrate that low loss photonic modes exist in dielectric material of finite dimensions near metal. Using truncated cylindrical disk geometry, we can form photonic nanocavities of TE01 characteristics with extremely small footprint of 0.83(λ/2neff)2, a physical size of 0.47(λ/2neff)3 and subwavelength mode volume of 0.3(λ/2neff)3 while maintaining low cavity losses through the creation of image charges in metal. In contrast to the case when a magnetic dipole mode is aligned in parallel with the metallic substrate its scattering cross section is strongly enhanced22; when the magnetic dipole mode is perpendicular to the metallic substrate, its image dipole is opposite to the original one and the radiation loss of the cavity to the far field is substantially suppressed. This type of photonic mode is analogous to the metallo-dielectric cavity in nature. Without the top metal coating and insulating layers, however, the fabrication steps can be considerably reduced. Our findings demonstrate a promising alternative to metallo-dielectric modes or hybrid plasmonic modes for the realization of nano-lasers using industry relevant materials and techniques.
Methods
COMSOL simulation
Wave optics module in COMSOL Multiphysics 5.2 simulation package is used for finite element simulations. To calculate the dispersion curves in the planar structures, effective mode indices in 2D simulation are obtained at different frequencies. The resonant frequencies, mode losses and mode distributions at various cavity diameters are obtained via 3D eigenfrequency calculation. In simulations for Fig. 1d and 3D simulations in Fig. 2 and Fig. 3, the permittivities of GaInP, AlGaInP, Ag and Cu are obtained via realistic material parameters as described in ref.18, ref.13, ref.8 and ref.23, respectively.
Guided TE photonic mode in a cylindrically shaped dielectric waveguide
To solve the Helmholtz equation in cylindrical coordinates (ρ, φ, z) with z direction as the propagation direction, we first need to solve for Hz component for a TE mode, which satisfies inside and outside the core19,26:
The simplest solution is \({H}_{z}(z)=F(\rho ){e}^{im\phi }{e}^{i\beta z}\) and F(ρ) satisfies:
F therefore satisfies Bessel equation in the core and modified Bessel equation outside the core. The simplest mode (m = 0) allows for TE characteristics. Hz is therefore:
and
Here \({\varepsilon }_{core}\) is the permittivity of the cylindrical core and \({\varepsilon }_{d}\) the permittivity of the outside dielectric, with \({\varepsilon }_{core} > {\varepsilon }_{d}\). The solution for Eφ is then:
And for Hr is:
The boundary conditions require Hz and Eφ continuous at ρ = R:
The above solution is accurate for infinitely long cylindrically shaped waveguide.
TE01 photonic mode in the dielectric-semiconductor (truncated cylindrical disk)-dielectric cavity and dielectric-semiconductor (truncated cylindrical disk)-dielectric-metal cavity
Semiconductor disk in dielectric
For a truncated semiconductor disk with top and bottom surface at z = ±a, the above solution is no longer valid. Assuming the dielectric material outside the semiconductor disk is the same everywhere, a good approximation for the electric and magnetic fields in the range of \(|z|\le a\) is5:
Here,
The standing wave approximation along z direction indicates the partial reflection of the waves at the top and bottom surfaces due to the discontinuity of permittivity of the semiconductor disk and surrounding dielectric. In \(|z| > a\) region, the solution to the Helmholtz equation is the superposition of a series of exponential decay and traveling Bessel functions (Hankel functions)27. We propose to use exponential decay function in z direction to approximate the evanescent fields in \(\rho \le R\,and\,|z| > a\) region, as shown below. The radiative terms to the far field are only considered when estimating the radiation loss of the cavity as will be discussed in more details in next session.
kd satisfies:
The relationship between constant A and C can be obtained by requiring Hr and Eφ continuous at z = ±a:
Semiconductor disk near metal
For the semiconductor disk on Al2O3/Ag or Al2O3/Cu, we can take a similar approach as we use to obtain the solution to the planar structure. We define an angle θ to describe how much the mode is pushed away from the middle of the semiconductor disk in z direction. The electric field can then be approximated by:
For the semiconductor disks near metal, we have:
Estimation of the resonant wavelength and quality factor of TE01 mode on glass and near metal
Estimation of TE01 resonant wavelength vs. disk radius
From Eq. (M1–M2), we can obtain:
Eq. (M11) is valid for semiconductor disk in dielectric or near metal.
Plug above three equations into Eq. (M11), we can solve for the TE01 resonant frequency ω as a function of semiconductor disk radius R in a dielectric medium via the Newton-Raphson method. Best fit to COMSOL simulations with realistic material parameters leads to \({{\rm{\varepsilon }}}_{{\rm{core}}}=12.5\) and \({{\rm{\varepsilon }}}_{{\rm{dielectric}}}=2.5\) in the wavelength range of 500 nm to 1.3 µm, as shown in Fig. 3c.
Combining Eq. (M8–M10), we can obtain a similar dispersion relationship as Eq. (7) in the main texts for the semiconductor disk near metal:
Combining Eq. (M11) and Eq. (M12), we obtain the TE01 resonant frequency ω as a function of semiconductor disk radius R for the disk near metal. Please note that in the analytical model we use dielectric-AlGaInP-dielectric-Ag structure in order to simplify the calculations. Best fit to COMSOL simulations with realistic material parameters leads to \({{\rm{\varepsilon }}}_{{\rm{core}}}=12.2\) and \({{\rm{\varepsilon }}}_{{\rm{dielectric}}}=2\) for the disks on Al2O3/Cu and \({{\rm{\varepsilon }}}_{{\rm{core}}}=12.5\) and \({{\rm{\varepsilon }}}_{{\rm{dielectric}}}=2\) for the disks on Al2O3/Ag in the wavelength range of 500 nm – 1 µm, as shown in Fig. 3c.
Estimation of TE01 Q vs. disk radius
To calculate the quality factor Q of the cavity, we need to know the radiation loss to the far field from the cavity and the internal loss of the cavity due to the absorption of the semiconductor material and the ohmic loss of the metal. As discussed in previous session, the accurate solution to Helmholtz equation in the far field is the superposition of a series of traveling Bessel functions and the calculation for radiation loss can be complicated5.
Here we propose a simplified model to estimate the radiation loss. We can calculate the equivalent polarization current density using the expression for polarization \(P=({\varepsilon }_{c}-1){\varepsilon }_{0}E=\rho x.\) So, \(\dot{P}=({\varepsilon }_{c}-1){\varepsilon }_{0}\dot{E}=\rho \dot{x}=J=\) \(-\,i\omega ({\varepsilon }_{c}-1){\varepsilon }_{0}E\) in the semiconductor disk. Since TE01 only has Eφ component and is constant in φ direction, total electric dipole moment is zero. Therefore, the lowest order radiation is the magnetic dipole radiation. We can calculate the total magnetic dipole due to polarization current density for the semiconductor disk in dielectric as:
For a magnetic dipole, its radiation power is \({P}_{rloss}=\frac{{\mu }_{0}{\omega }^{4}{|m|}^{2}}{12\pi {c}^{3}}\)19. Plugging the expression of m into this equation, we get:
\({\varepsilon }_{c}\) is in general a complex number. In the estimation of the radiation loss, we only use the real part of \({\varepsilon }_{c}.\)The internal loss \({P}_{iloss}\) is estimated for the entire volume using19:
The stored energy inside the semiconductor disk is calculated using5:
In the case of TE01 mode, the electric field only has \({E}_{\phi }\) component:
The quality factor Q can then be calculated using
Similar calculations can be carried out on the semiconductor disk on Al2O3/Ag and on Al2O3/Cu. Using the electric field expressions detailed in previous session, we have:
It is clear from the above expression that the first term is similar to the magnetic dipole \(\overrightarrow{m}\) of the semiconductor disk in a dielectric medium, apart from being multiplied by a factor of cosθ due to the presence of the metal substrate, which reduces the total magnetic dipole moment. The third term is the induced magnetic dipole by the image current of the metal in metal region. Since \(({\varepsilon }_{m}-1)\) is negative, the third term is in opposite direction to the first term. As a result, the magnetic dipole \(\overrightarrow{m}\) of the semiconductor disk on Al2O3/Ag and on Al2O3/Cu is substantially decreased compared to its counterpart in a dielectric medium and higher quality factor is achieved in the semiconductor disk on Al2O3/Ag and on Al2O3/Cu. The estimated Q of semiconductor disk in dielectric and near metal are plotted in Fig. 3(d). Please note that in the analytical model we use dielectric-AlGaInP-dielectric-Ag structure. The effective relative permittivity of the dielectric layer is obtained from the best fit to Fig. 3(c), in order to keep the analytical model self-consistent between Fig. 3(c) and Fig. 3(d). The loss of cavity is more sensitively related to the dielectric and insulator used in the COMSOL simulation than the resonant wavelength of the cavity. Nevertheless, we do think our analytical model reasonably reproduces the transition from radiation loss domination to internal loss domination region of the Q factors.
Data Availability
The datasets generated during and/or analysed during the current study are available from the corresponding author on reasonable request.
References
Smit, M., van der Tol, J. & Hill, M. Moore’s law in photonics. Laser & Photonics Reviews 6, 1–13 (2012).
Ding, K. & Ning, C. Z. Fabrication challenges of electrical injection metallic cavity semiconductor nanolasers. Semicond. Sci. Technol. 28, 124002 (2013).
Hill, M. T. et al. Lasing in metallic-coated nanocavities. Nature Photonics 1, 589–594 (2007).
Nezhad, M. P. et al. Room-temperature subwavelength metallo-dielectric lasers. Nature Photonics 4, 395–399 (2010).
Manolatou, C. & Rana, F. Subwavelength Nanopatch Cavities for Semiconductor Plasmon Lasers. IEEE Journal of Quantum Electronics 44, 435–447 (2008).
Yu, K., Lakhani, A. & Wu, M. C. Subwavelength metal-optic semiconductor nanopatch lasers. Optics Express 18, 8790–8799 (2010).
Hill, M. T. & Gather, M. C. Advances in small lasers. Nature Photonics 8, 908–918 (2014).
Oulton, R. F. et al. Plasmon lasers at deep subwavelength scale. Nature 461, 629-632 (2009).
Zhang, Q. et al. A room temperature low-threshold ultraviolet plasmonic nanolaser. Nature Communications 5, 4953 (2014).
Lu, Y. J. et al. Plasmonic nanolaser using epitaxially grown silver film. Science 337, 450–453 (2012).
Lu, Y. J. et al. All-color plasmonic nanolasers with ultralow thresholds: autotuning mechanism for single-mode lasing. Nano Letters 14, 4381–4388 (2014).
Ma, R.-m., Oulton, R. F., Sorger, V. J., Bartal, G. & Zhang, X. Room-temperature sub-diffraction-limited plasmon laser by total internal reflection. Nature Materials 10, 110–113 (2011).
Liu, N. et al. Lithographically defined, room temperature low threshold subwavelength red-emitting hybrid plasmonic lasers. Nano Letters 16, 7822–7828 (2016).
Lakhani, A. M., Kim, M.-k, Lau, E. K. & Wu, M. C. Plasmonic crystal defect nanolaser. Optics Express 19, 18237–18245 (2011).
Chou, Y. H. et al. High-operation-temperature plasmonic nanolasers on single-crystalline Aluminum. Nano Letters 16, 3179–3186 (2016).
Costantini, D. et al. A hybrid plasmonic semiconductor laser. Appl. Phys. Lett. 102, 101106 (2013).
Maier, S. A. Plasmonics: Fundamentals and Applications. (Springer, 2007).
Schubert, M. et al. Optical constants of GaxIn1-xP lattice matched to GaAs. J. Appl. Phys. 77, 3416 (1995).
Jackson, J. D. Classical Electrodynamics. 3rd edn, (John Wiley & Sons, Inc, 1999).
Cohn, S. B. Microwave bandpass filters containing high-Q dielectric resonators. IEEE Trans. Microwave Theory Tech. MTT-16, 218–227 (1968).
Xifre-Perez, E. et al. Mirror-image-induced magnetic modes. ACS nano 7, 664–668 (2013).
Huang, Z. et al. Strong-field-enhanced spectroscopy in Silicon nanoparticle electric and magnetic dipole resonance near a metal surface. J. Phys. Chem. C 119, 28127–28135 (2015).
Rakic, A. D., Djurisic, A. B., Elazar, J. M. & Majewski, M. L. Optical properties of metallic films for vertical-cavity optoelectronic devices. Appl. Opt. 37, 5271–5283 (1998).
Huang, Z. et al. Nanoscale active hybrid plasmonic laser with a metal-clad metal–insulator–semiconductor square resonator. J. Opt. Soc. Am. B 31, 1422–1429 (2014).
Kwon, S.-H. Deep subwavelength plasmonic whispering gallery-mode cavity. Optics Express 20, 24918–24924 (2012).
Snyder, A. W. & Love, J. D. Optical Waveguide Theory. (Chapman and Hall, 1983).
Balanis, C. A. Antenna Theory. 2nd edn, (John Wiley & Sons, Inc, 1997).
Acknowledgements
N.L. and G.S. thank the support by University of Limerick-University of Massachusetts Boston Strategic Alliance Joint Seed Fund. N. L. acknowledge the support by Science Foundation Ireland Career Development Award 17/CDA/4733.
Author information
Authors and Affiliations
Contributions
N.L. conceived the idea after discussions with G.S. and B.C. N.L. did the calculations and simulations. C.S. helped with the simulations. N.L. wrote the manuscript. All authors read the manuscript and gave comments and made modifications to the manuscript.
Corresponding author
Ethics declarations
Competing Interests
The authors declare no competing interests.
Additional information
Publisher’s note: Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Electronic supplementary material
Rights and permissions
Open Access This article is licensed under a Creative Commons Attribution 4.0 International License, which permits use, sharing, adaptation, distribution and reproduction in any medium or format, as long as you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons license, and indicate if changes were made. The images or other third party material in this article are included in the article’s Creative Commons license, unless indicated otherwise in a credit line to the material. If material is not included in the article’s Creative Commons license and your intended use is not permitted by statutory regulation or exceeds the permitted use, you will need to obtain permission directly from the copyright holder. To view a copy of this license, visit http://creativecommons.org/licenses/by/4.0/.
About this article
Cite this article
Liu, N., Silien, C., Sun, G. et al. Low loss photonic nanocavity via dark magnetic dipole resonant mode near metal. Sci Rep 8, 17054 (2018). https://doi.org/10.1038/s41598-018-35291-w
Received:
Accepted:
Published:
DOI: https://doi.org/10.1038/s41598-018-35291-w
Keywords
Comments
By submitting a comment you agree to abide by our Terms and Community Guidelines. If you find something abusive or that does not comply with our terms or guidelines please flag it as inappropriate.