Abstract
With the extraction of hydrocarbons from reservoirs, fractures will gradually close and their permeabilities will be reduced. Therefore, fracture conductivity will change dynamically during hydrocarbon extraction. The main objective of this study is to develop a new semi-analytical model to simulate the flow inside a homogenous porous medium containing discretely distributed fractures with dynamic conductivities. Based on a dynamic-conductivity model, the pressure and pressure-derivative characteristics of a well on or near discrete dynamic-conductivity fractures were simulated. The results show that four flow regimes can be identified for a well near a dynamic-conductivity fracture. Dips in the pressure-derivative curves in the transitional flow period were observed as soon as pressure disturbances reached a fracture. In addition, humps caused by the effects of dynamic conductivity were observed after the transitional flow period. Wider and deeper dips were found on the pressure/pressure-derivative curves of a well surrounded by multiple fractures. The novel model presented here can provide a tool for elucidating the flow mechanisms of fluids in closed rectangular reservoirs with discretely dynamic-conductivity fractures.
Similar content being viewed by others
Introduction
Discrete fractures are fractures that are distributed in sandstone and carbonate formations and include unconnected natural fractures, faults and hydraulic fractures1,2,3. In many naturally fractured reservoirs, fractures and faults can be discrete rather than forming connected network systems4,5. The presence of discrete fractures contributes greatly to the enhanced production of oil and gas.
The fractures can be divided into three categories: uniform-flux fractures, infinite-conductivity fractures and finite-conductivity fractures. For uniform-flux fractures, we assume the flow rate along the fracture surface is uniform. The original uniform-flux/infinite-conductivity solutions for a vertically fractured well were developed by Gringarten et al.6. The wellbore pressure of an infinite-conductivity fracture can be obtained in the uniform-flux fracture case by measuring the pressure drop at 0.732 in the fracture. Cinco et al.7 found that the assumption of an infinite-conductivity fracture ignoring the pressure drop along the fracture may lead to errors for low and moderate fracture conductivities. The authors defined this type of low and moderate conductivity fracture as a finite-conductivity fracture.
Many studies have reported investigations of transient pressure analyses for vertical wells on single hydraulic fractures6,7,8,9,10,11 and horizontal wells intercepted by multiple hydraulic fractures12,13,14,15,16,17,18,19. Cinco and Samaniego8 discussed the flow regimes in detail for a finite-conductivity fracture. They first presented the entirety of flow regimes for a finite-conductivity fracture, i.e., bilinear flow, formation linear flow and radial flow regimes. Based on the flow regimes, reservoir parameters can be obtained through interpretations of well tests. Berumen et al.9 also investigated the pressure behaviours of wells intercepting asymmetric fractures of both infinite and finite conductivity under constant rates using numerical methods. Tiab et al.10 applied the Tiab’s Direct Synthesis technique to evaluate fracture asymmetry in finite-conductivity fracture wells producing at a constant rate. Luo and Tang11 proposed a model to discuss the pressure response of a varying-conductivity fracture. Larsen and Hegre12 rigorously presented a transient pressure solution for horizontal wells with circular finite-conductivity fractures in a three-dimensional unbounded formation using the Laplace transform method. Crosby et al.13 developed an analytical and experimental study of the initiation of transverse fractures from horizontal wells. Wan and Aziz14 described a new semi-analytical solution for horizontal wells with multiple hydraulic fractures. The fractures can be rotated at any horizontal angle to the well, and they need not fully penetrate the formation in the vertical direction. Wei and Economide15 provided a calculation procedure for transverse fractures and related the performance of each fracture with well-established methodologies such as the dimensionless productivity index. Medeiros et al.16 presented a discussion of diagnostic pressure and pressure-derivative plots for hydraulically fractured horizontal wells in locally and globally fractured formations. Brown et al.17 adopted a classic tri-linear flow model to simulate the pressure-transient and production behaviours of fractured horizontal wells in an unconventional shale reservoir. Zhao et al.18 presented a “tri-porosity” mathematical model to describe fluid flow from a shale gas formation to a multi-fractured horizontal well. Yuan et al.19 established a simple, practical and time-efficient septa-linear flow model to obtain the transient pressure and production.
Unlike hydraulic fractures that connect to the wellbore, discrete fractures and faults may not be connected to the wellbore but, rather, are at a distance. The effects of discrete fractures on pressure responses have also been studied20,21,22,23,24,25,26,27. Givens and Crawford20 studied the influence of isolated fractures on fluid-displacement response. They reported that the fracture orientation and length and the fracture-to-well distance are the key parameters that control well performance. Based on assumptions of steady-state-flow behaviour and uniform fracture distribution, Huskey and Crawford21 studied the effect of isolated vertical fractures on pressure distribution. Cinco et al.22 developed an analytical model to study the transient-flow behaviours of a well near a single natural infinite-conductivity fracture in an infinite reservoir. Guo and Evans23 presented the pressure-transient behaviours of a horizontal well penetrated by multiple randomly distributed vertical fractures in an infinite reservoir and bounded reservoir. Izadi and Yildiz24 presented a semi-analytical model for transient flows into multiple vertical wells producing from a porous medium containing randomly distributed discrete fractures. Zeng et al.25 discussed the pressure response for a vertical well with discrete fractures by accounting for the effects of non-Darcy flow. Based on their work, three flow regions, i.e., fluid flow near the wellbore, fracture-dominated fluid flow and fluid flow in the matrix away from the fracture can be identified. Biryukov and Kuchuk26,27 presented a mesh-free semi-analytical solution for pressure-transient behaviour in a 2 Dimensional infinite reservoir containing a network of discrete or connected finite- and infinite-conductivity fractures.
The fracture conductivities reported in the above literature were assumed to be constant. However, a reduction in formation pressure will result in increases in effective closure stress on the discrete fractures in an oilfield. Hence, fractures will gradually close, leading to dynamic decreases in fracture permeability and conductivity with time. A transient pressure analysis for a vertical well on a dynamic-conductivity fracture has been investigated using semi-analytical and numerical methods28,29,30,31,32,33. Chen and Evers28 developed a simple model to illustrate the performance of a fractured well with stress-sensitive conductivity. Berumen and Tiab29 revealed the effects of pressure on permeability and conductivity using a numerical method. Pedroso and Correa30 developed a new model to discuss the effects of permeability on the flow behaviour of a fractured well. Cho et al.31 presented experimental data for a pressure-dependent natural facture. Zhang et al.32 presented the results of a study that analysed the build-up of pressure in a vertically fractured well while considering stress-sensitive permeability and hysteresis effects in fractures. Wang and Aryana33 investigated how stress-dependent fracture apertures and their spatial variations affected production from unconventional gas reservoirs with complex fracture geometries.
As noted above, the transient pressure behaviours of wells due to constant-conductivity fractures6,7,8,9,10,11,12,13,14,15,16,17,18,19 and dynamic-conductivity fractures have been discussed28,29,30,31,32,33. In addition, transient pressure responses of wells near constant-conductivity fractures have been studied20,21,22,23,24,25,26,27. However, to the best of our knowledge, few studies have discussed the transient pressure behaviours of wells near discrete fractures with dynamic conductivities in closed rectangular reservoirs. In this paper, we develop a new semi-analytical method that is an extension of the popular transient pressure calculation method proposed by Cinco et al.7,8 to examine the pressure responses of a vertical well in a reservoir with discrete dynamic-conductivity fractures. The oil or gas is assumed to be produced only through the vertical well.
This paper presents a novel semi-analytical model of a vertical well with dynamic-conductivity fractures in a rectangular reservoir. Two verification cases (a well on a dynamic-conductivity fracture in an infinite reservoir and a well near a constant-conductivity fracture in an infinite reservoir) and the effects of various parameters on the dimensionless pressure of a vertical well are studied. The effects of boundary size and dynamic conductivity on the dimensionless pressure of a vertical well on a fracture are presented. Additionally, the effects of fracture location, initial conductivity, dynamic conductivity, and distance between the well and fracture on the dimensionless pressure of a vertical well in the vicinity of discrete fractures are presented. Finally, the effects of fracture number and dynamic conductivity on the dimensionless pressure of a vertical well around four fractures are presented.
Mathematical Models
Basic assumptions
In this paper, we assume that the discrete fractures are not joined and that the oil or gas is produced only through a vertical well (Fig. 1A). Additional basic assumptions are given below.
-
1)
The closed rectangular reservoir is isotropic and homogeneous. The reservoir has constant thickness h, constant porosity φ and constant permeability k. The reservoir contains a slightly compressible single-phase fluid of constant compressibility c t and constant viscosity μ.
-
2)
The reservoir is fully penetrated by vertically discrete fractures. No fluids are assumed to flow into the fractures at their tips. Moreover, the fluids in the fractures are assumed to be incompressible. Each fracture is divided into multiple segments of equal length and uniform flux (Fig. 1B).
-
3)
Production of a vertical well with a constant rate from a closed reservoir leads to a reduction in fluid pressure and subsequent increase in net closure stress on the fractures. Fracture permeability changes with formation pressure. Thus, the dynamic conductivity of a discrete fracture is used to describe this phenomenon. The flows in the formation and fractures are assumed to obey Darcy’s law.
Model of fracture dynamic conductivity
According to the effective stress law, any change in effective stress must be compensated for changes in pore pressure, indicating that the variation of permeability caused by a stress change can be expressed as a function of pore pressure. Experiments and exponential models have been used to characterize the relationship between pressure and permeability28,29,30,31,32,33.
We chose a more general model used by Zhang et al.32 for this paper. The relationship between fracture permeability and pore pressure is described as
The fracture permeability can be written as
where: Subscripts “f” is fracture property; “min” is minimum;“i” is initial or segment; k f is fracture permeability, mD; p is pressure, psi; γ f is fracture permeability modulus.
According to the definitions of the dimensionless parameters (Appendix A), the dimensionless dynamic conductivity of a fracture is
Note that C fD is not constant but, rather, a function of the dimensionless fracture pressure \({p}_{fD}\). In other words, C fD evolves spatially and temporally, and Eq. 3 can be further expressed as
where: Subscripts “D” is dimensionless; C fD is the initial fracture conductivity corresponding to the initial formation pressure.
Model of fluid flow in the reservoir
The wing model introduces a way to flexibly generate complex fractures when describing discrete fractures34. We assume that there are M wings and a vertical well in a closed rectangular reservoir. The well can be on a fracture or near fractures. The flow rate in the wellbore is q w. The m-th wing is divided equally into N m segments with uniform fluxes (Fig. 1B). The dimensionless pressure of each segment can be obtained in the Laplace domain using the superposition principle.
(1) The well is on the fracture.
(2) The well is not on the fracture.
For each segment,
For the well,
where: the subscript “w” is wellbore property; “ij” indicates the j-th segment of the i-th fracture wing; “e” is boundary; M is the numbers of wings; N k is segments with uniform fluxes; \({\bar{p}}_{ufD(ij,km)}\) and \({\bar{p}}_{uwDij}\) are the changes in dimensionless pressure at the j-th segment of the i-th wing caused by the production of the m-th segment of the k-th wing and the vertical well in the Laplace domain, respectively; x D and y D are dimensionless coordinate in the x and y direction, respectively; x eD and y eD are dimensionless boundary coordinate in the x and y direction, respectively.
The uniform-flux fracture solution \({\bar{p}}_{ufD(ij,km)}\) and point source solution \({\bar{p}}_{uwD}\) in a rectangular reservoir can be obtained from the literature35,36.
Model of fluid flow in the fracture
For fluid flow in a dynamic-conductivity fracture, the fracture conductivity C fD is correlated with \({p}_{fD}\). Because \({p}_{fD}\) is changing spatially and temporally, the fracture can be considered to exhibit varying conductivity at each step.
A dimension transformation method is introduced to convert the varying-conductivity, equal-length fracture into a constant-conductivity, unequal-length fracture (Appendix B, Fig. 2)11.
A detailed derivation of fluid flow in a dynamic-conductivity fracture is presented in Appendix B. After the transformation, the equation for a varying-conductivity fracture at each time step can be written as
where: ξ D is dimensionless coordinate in the ξ direction; \({\rm{\Delta }}{\xi }_{Di}\) and \({\rm{\Delta }}{\xi }_{Dn}\) are dimensionless discretized step of the i-th and n-th segments in the ξ direction; \({\rm{\Delta }}{y}_{Di}\)dimensionless discretized step of the i-th segment in the y direction
Coupling model
According to the continuity condition whereby pressure and flux must be continuous along a fracture’s surface, the following conditions must hold along the fracture plane:
If the well is on the fracture,
If the well is not on the fracture,
where: s is time variable in Laplace domain, dimensionless; \({\bar{q}}_{wD}\) dimensionless wellbore flow rate of a well, in Laplace domain, dimensionless; \({\bar{q}}_{fDkj}\) is dimensionless wellbore flow rate of a fracture at “kj” in Laplace domain, dimensionless.
For the simultaneous calculation of Eqs (4–10), the pressure solution can be obtained via the Gaussian elimination method and can further be inverted to the time domain using the Stehfest numerical algorithm. With production, fracture pressure will gradually decrease, and the dynamic conductivity should be updated along the fracture at each time step. Based on the semi-analytical solution, an iterative program can be used to calculate the dimensionless pressure and flux distribution at each time step (Appendix C). The conductivity distributions along the fracture can then be obtained for each time step.
Model verification
To the best of our knowledge, there are no existing models for discrete fractures of dynamic conductivity for comparison. In this section, two specific models, i.e., a well near a discrete fracture of constant conductivity and a well on a fracture with dynamic conductivity, are used to verify our model.
Comparison with a well near a discrete fracture with constant conductivity
A transient-flow solution for an infinite-conductivity discrete fracture near a vertical well was presented by Cinco et al. in a real domain22. The calculation parameters are listed in Fig. 3(A).
Comparison with a fractured well with varying conductivity
Zhang et al.32 developed a finite-difference numerical simulator to model a vertical well on a symmetric fracture of varying conductivity in an infinite reservoir. Figure 3(B) displays the comparison of our model with other models for a constant fracture conductivity.
As shown in Fig. 3(A), our model is in significant agreement with the model of Cinco et al.22. (the solid lines are the results from our model, and the circles with crosses are from the model of Cinco et al.22). As shown in Fig. 3(B), our semi-analytical model (solid lines) agrees closely with the numerical solution of the Zhang et al. model32. The circles represent a well on a symmetric fracture with an initial conductivity = 0.5π. The upper group of curves is dimensionless pressure, and the lower group is its derivative. The red, green, blue and black lines represent the values for γ fD = 3, 2, 1 and 0, respectively. If γ fD = 0, the fracture conductivity remains constant for all time, and if γ fD > 0, the conductivity changes with production.
The model verification proves that our model is accurate and that it can be further used in calculations for complex cases.
Results and Discussions
We focus on the effects of dimensionless permeability modulus γ fD , discrete-fracture-well distance D, initial discrete-fracture conductivity C fDi and boundary size \({x}_{eD}\times {y}_{eD}\) on dimensionless pressure. Based on the new semi-analytical method presented above, three fundamental cases are presented in detail.
Case 1 is a pressure-transient analysis of a vertical well on a fracture, where the effects of boundary size, dynamic conductivity and dimensionless permeability modulus on the dimensionless pressure and pressure derivative are addressed (Fig. 4).
Case 2 is a pressure-transient analysis of a vertical well in the vicinity of discrete fractures. This case focuses on the effects of fracture conductivity, dimensionless permeability modulus, fracture number, distance between the well and fracture on the dimensionless pressure and pressure derivative (Fig. 5).
Case 3 is a case study employing synthetic data to obtain the pressure derivative for the discrete-fracture-well system (Fig. 6).
Pressure-transient analysis of a vertical well on a fracture
A fracture is assumed to be located at the centre of a closed square reservoir with \({x}_{eD}={y}_{eD}=20\). A vertical well on the fracture is under production at a constant production rate.
Effects of dimensionless permeability modulus
Figure 4 presents the curves of dimensionless pressure (solid line) and pressure derivative (dashed line) vs. dimensionless time for a symmetrical fracture with different dimensionless permeability moduli γ fD . In Fig. 4(A), the red, blue and black lines represent the values for γ fD = 3, 1 and 0, respectively. For γ fD = 0 (black lines), i.e., constant fracture conductivity, the characteristic flow regimes can be identified on the derivative curve: bilinear flow with a slope of 1/4, formation linear flow with a slope of 1/2, radial flow with a constant value of 1/2 and boundary-dominated flow with a slope of 1. The sub-figure presents the ratios of the average fracture conductivities C fDa to initial fracture conductivities C fDi over time for different dimensionless fracture permeability moduli γ fD : 3(red line), 1 (blue line) and 0 (horizontal black line). The transition point is defined as the time corresponding to the occurrence of the minimum fracture conductivity \({C}_{fD\min }\). For γ fD = 0 (black lines), no transition point exists. For γ fD = 3 (red line) and γ fD = 1 (blue line), the transition points can be found (marked by the red solid and blue solid circles, respectively) on the dimensionless pressure curves. Before the transition points, the fracture makes a dynamic contribution to well production. We define the time before a transition point as the dynamic-conductivity flow period. After that time, the fracture conductivity will remain constant and at a minimum \({C}_{fD\min }\).
We set the initial C fDi and minimum fracture conductivities \({C}_{fD\min }\) to π and 0.1π, respectively. As shown in Fig. 4(A) (sub-figure), an obvious decrease in dimensionless fracture conductivity C fD can be observed with decreasing dimensionless permeability modulus γ fD .With increasing dimensionless permeability modulus γ fD , dimensionless pressure increases, which means that a larger pressure drop is needed to maintain a constant production rate. In addition, due to the influence of permeability modulus (γ fD > 0), the pressure and pressure-derivative curves deviate from the type match curve (γ fD = 0). Thus, the characteristic flow regime for a symmetric fracture (bilinear flow with a slope of 1/4, formation linear flow with slope of 1/2 and radial flow with the derivate of 1/2) cannot be identified.
We define the intervals when the flow exhibits dynamic fracture conductivity and minimum fracture conductivity as dynamic-conductivity flow and minimum-conductivity flow periods, respectively. For small permeability moduli γ fD , long dynamic flow periods and high oil recoveries can be expected. The transition points between two flow periods for γ fD = 1 and γ fD = 3 are marked with a solid circle in Fig. 4(A). A rapid decrease in dynamic fracture conductivity C fD with high permeability modulus γ fD (Fig. 4(A) sub-figure) results in a small dimensionless time corresponding to the transition point such as t D = 3 for γ fD = 3 and t D = 300 for γ fD = 1, which indicates that fracture effectiveness decreases with increasing values of γ fD .
Effects of dimensionless initial fracture conductivity
Figure 4(B) illustrates the effect of initial fracture conductivity C fDi on dimensionless pressure with (dash line, γ fD = 3) and without (solid line, γ fD = 0) considering the effects of the permeability modulus. In Fig. 4(B), the red, green, blue and black lines correspond to the values of initial fracture conductivity, C fDi = 100π, 10π, π and 0.1π. The ratios of the average fracture conductivities C fDa to initial fracture conductivities C fDi for different initial dimensionless fracture conductivities C fDi are illustrated in the sub-figure of Fig. 4(B). Four transition points are identified on the dimensionless pressure curves (dashed lines) for γ fD = 3.
For the purpose of comparison, we specified that the minimum fracture conductivities were all \({C}_{fD\min }\) = 0.05. For low initial conductivities, for example, C fDi = 0.1π, the effect of permeability modulus v on dimensionless pressure is relatively stable (no apparent climbing) throughout the entire production period. As initial fracture conductivity increases, the effect of permeability modulus γ fD on dimensionless pressure will be delayed. For C fDi = 100π, the pressure responses for γ fD = 0 and γ fD = 3 are nearly indistinguishable for t D less than 1. However, a stronger effect gradually appears for larger dimensionless times, such that t D = 10−2–10−1 for C fDi = π, 10−1–100 for C fDi = 10π and 100–101 for C fDi = 100π, where significant increases in dimensionless pressure can be observed. In addition, longer dynamic-conductivity flow periods resulting from larger initial conductivities can be observed from the curves, where the transition points are marked as solid circles. Therefore, large initial fracture conductivities C fDi can delay and strengthen the effects of permeability modulus γ fD on dimensionless pressure. As shown in the sub-figure of Fig. 4(B), it takes longer for C fD to decrease to the minimum conductivity \({C}_{fD\min }\) as C fDi increases.
Effects of boundary size
Figure 4(C,D) demonstrates the effects of boundary size on pressure response at γ fD = 0.5 and C fDi = 20. Figure 4(C) displays the effects of boundary size on dimensionless pressure and its derivative for a well on a symmetric fracture at γ fD = 0.5. The red, blue and black lines correspond to the boundary size values: \({x}_{eD}={y}_{eD}\) = 1000, 100 and 20. The dimensionless pressures and their derivatives are represented by the solid and dashed lines, respectively. Figure 4(D) displays the ratios of average conductivity C fDa to initial conductivity C fDi over time for different boundary sizes at γ fD = 0.5. The red, blue and black lines correspond to the boundary size values, \({x}_{eD}={y}_{eD}\) = 1000, 100 and 20, respectively.
Figures 4(C) and (D) show that the small distance between the well and boundary not only caused the boundary-dominated flow (BDF) to occur earlier but also accelerated the declining rate of the average conductivity of the fracture. Apparently, the existing boundary will significantly impact fracture conductivity and produce notable differences when the pressure response reaches it. This phenomenon is caused by the rapid drop in the average pressure after the boundary-dominated-flow period, which further leads to obvious decreases in dynamic fracture conductivity C fD . Thus, a shorter distance to the boundary will enhance the effect of permeability modulus γ fD on dimensionless pressure.
Pressure-transient analysis of a vertical well in the vicinity of discrete fractures
For discretely fractured reservoirs, a well may be drilled in the vicinity of discrete fractures with dynamic conductivities. The production of the well will be affected by the fractures. In this section, we will discuss the pressure behaviours of a vertical well in the vicinity of discrete fractures within a closed square reservoir with \({x}_{eD}={y}_{eD}\) = 20.
Effect of the constant fracture conductivity on the dimensionless pressure
To reveal the influence of the relationship between the well and a constant-conductivity fracture (C fD = C fDi = 1500, γ fD = 0) on dimensionless pressure, we set the dimensionless distance to 0.01, 0.1, and 1.0.
Figure 5(A,B) demonstrates the effects of dimensionless distance between the well and discrete fracture on dimensionless pressure and its derivative (the well and fracture are collinear) (γ fD = 0). Four flow regimes on the derivative curve are shown (black dashed line), i.e., early-time radial flow, transitional flow, middle-time pseudo-radial flow, and boundary-dominated flow. Dimensionless pressure and its derivative are represented by solid and dashed lines, respectively. The red, blue and black lines correspond to dimensionless distances of 1, 0.1 and 0.01, respectively. Figure 5(A) shows that the well and fracture are collinear. Figure 5(B) shows that the well is perpendicular to the fracture.
The durations of the transitional flows for Fig. 5(A) and (B) differed, as shown in the figures. After a period of middle-time pseudo-radial flow, a propagating pressure front would approach the fracture and transitional flow would occur. In that flow period, downward dips in the derivative curves can be observed. The durations and depths of the dips depend on the well-fracture distance. With increasing dimensionless distance, dips become narrower and shallower, representing the gradually decreasing effect of the fracture on wellbore pressure. When the distance is greater than 1, transitional flow is not detected. A comparison of Fig. 5(A) and (B) shows the stronger influence of the collinear case (wider and deeper dip, Fig. 5(A)) than that of the perpendicular case (Fig. 5(B)).
After the transitional flow period, middle-time pseudo-radial flow with a pressure derivative of 0.5 occurs. Finally, boundary-dominated flow is achieved. In the middle-time pseudo-radial flow and boundary-dominated flow period, the curves of pressure-derivative overlap.
Effects of dynamic fracture conductivity on dimensionless pressure
We now focus on the effects of permeability modulus γ fD , dimensionless distance and initial fracture conductivity C fDi on dimensionless pressure with a dynamic-conductivity fracture near a vertical well. The parameters used for the calculations are listed on the figures.
-
1)
Effects of permeability modulus. Figure 5(C) shows the effects of permeability modulus γ fD on dimensionless pressure. Dimensionless pressure and its derivative are represented by solid and dashed lines, respectively. The red, green, blue and black lines correspond to the dimensionless permeability modulus values,γ fD = 3, 2, 1, and 0, respectively. The effect of γ fD on dimensionless pressure derivative is concentrated in the middle-time pseudo-radial flow period. Three transition points can be seen. The presence of the dynamic fracture conductivity causes the pressure-derivative curves to deviate from the constant-conductivity curve (γ fD = 0). A hump can be found in the middle-time pseudo-radial flow and boundary-dominated flow periods, which indicates the occurrence of sharp pressure drops, and accordingly, the middle-time pseudo-radial flow is invisible.
-
2)
Effects of distance. Figure 5(D) presents the effects of dimensionless distance on the pressure responses. Dimensionless pressure and its derivative are represented by solid lines and dashed lines, respectively. The red, blue and black lines correspond to dimensionless distance values of 1, 0.1 and 0.01, respectively. A hump caused by the effects of dynamic conductivity in the middle-time pseudo-radial flow period can be found in the pressure-derivative curves by comparing Fig. 5(D) (γ fD = 3) with Fig. 5(B) (γ fD = 0). Note that when the dimensionless distance is greater than 1, the effect of the fracture can be ignored.
-
3)
Effects of initial fracture conductivity. Figure 5(E) demonstrates the effects of initial fracture conductivity C fDi on dimensionless pressure and its derivative with dynamic fracture conductivity (γ fD = 3). Dimensionless pressure and its derivative are represented by solid and dashed lines, respectively. The wine, blue, green, red and black lines correspond to the initial conductivity values (C fDi = 0.2, 2, 20, 200 and 2000, respectively). As shown in Fig. 5(E), the dip in the transitional flow period deepens and the height of the hump on the pressure-derivative curve in the middle-time pseudo-radial flow period increases with increasing initial fracture conductivity. For extremely small initial fracture conductivities such as C fDi = 0.2, the dips and humps nearly disappear.
Based on the discussion of a dynamic-conductivity fracture near a well, the presence of fractures benefits production, which leads to reductions in pressure drop (dips). Wider and deeper dips can be obtained when fractures are close to wells. In contrast, due to the decrease in dynamic conductivity with production, a hump can be observed in the middle-time pseudo-radial flow period, which indicates that a steep increase in pressure drop occurred. Thus, it is very important to make use of the early-time radial flow and transitional flow periods for production. For the middle-time pseudo-radial flow and boundary-dominated flow periods, the fracture negatively impacts production because the sharp declines in dynamic conductivity result in large pressure drops (humps).
Pressure-transient analysis of a vertical well near multiple fractures
To illustrate the effects of fracture number, we set 4 fractures around a vertical well. The dimensionless pressures and their derivatives for a well near a discrete fracture or multiple fractures at dimensionless distance D = 1 are compared in Fig. 5(F). In Fig. 5(F), dimensionless pressure and its derivative are represented by solid lines and dashed lines, respectively. The red lines correspond to a well near a fracture with γ fD = 3. The black lines correspond to a well surrounded by 4 fractures with γ fD = 3. The blue lines correspond to a well surrounded by 4 fractures with γ fD = 0.
From Fig. 5(F), when compared against the case with a fracture near a well (red line), an obvious dip can be found on the pressure-derivative curve for four fractures around a well (blue line). Therefore, to maintain a consistent outcome, lesser pressure drops are needed for a well surrounded by multiple fractures. Similar to the single fracture near a well, a hump on the pressure-derivative curve is found after transitional flow (black line).
Case study
Here, a case employing synthetic data is used to examine the pressure-derivative characteristics of a vertical open hole producing from a formation dissected by 42 discrete fractures with lengths between 100 and 450 ft (Fig. 1). All the fractures deviate from the horizontal axis by an azimuthal angle of 50 degrees. The fracture lengths and locations were randomly selected. Figure 1 shows the fracture pattern and distribution in a Cartesian coordinate system. Only one vertical open hole is producing from the discrete fractured formation at a constant production rate (q w = 20 stb/day). The well location in the formation is variable.
We consider two different cases for the well location. The positions of the vertical open hole in each case are marked with solid circles in Fig. 1. In Case 1, the vertical open hole is located at x w = 1335 ft and y w = 2533 ft. In this case, the vertical well is relatively distant from the nearby fractures and close to the boundary. In Case 2, the well is positioned near the centre of the reservoir at x w = 1520 ft and y w = 620 ft and is very close to four discrete fractures. The basic data for the reservoir and fluid used in the simulations are listed in Fig. 6. Figure 6 presents the pressure-derivative responses of a vertical well in a closed rectangular reservoir with discrete fractures. Figure 6 indicates that the expected three flow regimes—early-time radial flow, transitional flow period and boundary-dominated flow—are observed in both cases.
At very early times, only the formation around the vertical well contributes to flow. The pressure disturbance created at the wellbore has not yet arrived at the fracture. The logarithmic pressure derivative during the early-time radial flow period is constant at 40.8 psi. At this time, there is no fluid flow in or across the fracture. As soon as the pressure disturbances generated at the wellbore reaches the fracture, flows in and around the fracture are triggered and transitional flow occurs. During the transitional flow period, the pressure derivative decreases and then increases. Obvious dips can be observed on the curves. Comparing Case 1 with Case 2, a deeper dip is seen for Case 2 due to the effect of multiple fractures around the wellbore. The duration of the transitional flow period is controlled by fracture length, distance to fracture, fracture prosperities and fracture number.
After the transitional flow period, given the same discrete-fracture field, the location of the vertical open hole makes a significant difference in the derivative response during the late-time flow period. The position of the wellbore in Case 1 is close to the boundary and away from the fractures, the boundary-dominated flow prevails during the late-time period, and the middle-time pseudo-radial flow period does not exist on the curve. For Case 2, the well is located near the centre of the reservoir and is surrounded by 4 fractures and a hump caused by the decrease in fracture conductivity with production can be found on the curve. In addition, the boundary-dominated flow period is delayed due to the large distance between the well and boundaries.
Conclusions
Based on our work, the following conclusions can be drawn.
-
1)
A novel fracture model that accounts for the effect of dynamic conductivity as a function of pressure was established. Based on a dimension transformation from a varying-conductivity, equal-length fracture to a constant-conductivity, unequal-length fracture, a new semi-analytical solution for a dynamic-conductivity discrete fracture was developed in the Laplace domain. The new method is simple, computationally stable and accurate.
-
2)
The pressure behaviours of a vertical well on a dynamic-conductivity fracture have been discussed in detail. The effects of boundary size, fracture conductivity and dimensionless permeability modulus on the dimensionless pressure have been presented. The results show that well location mainly affects the early-time flow, dynamic fracture conductivity mainly affects the middle-time flow and large initial fracture conductivity will delay the effect of dynamic conductivity on dimensionless pressure during the middle-time flow period.
-
3)
For a closed rectangular reservoir, the dynamic conductivity of a discrete fracture that depends on the fracture pressure will be reduced dramatically. A small reservoir size will strengthen the effect of dynamic fracture conductivity on dimensionless pressure.
-
4)
The pressure response of a vertical well in the vicinity of a discrete fracture has been revealed. Four flow regimes can be found: early-time radial flow, transitional flow, middle-time pseudo-radial flow and boundary-dominated flow. The middle-time pseudo-radial flow may be masked by the effect of dynamic fracture conductivity. The presence of a fracture near a well is beneficial to production and leads to a reduction in the pressure drop (dip). In contrast, due to decreases in the dynamic conductivity of the fracture with production, a hump can be observed in the middle-time pseudo-radial flow period, which indicates that a steep increase in pressure drop has occurred.
-
5)
In comparison with those for a single fracture near a well, higher production rates can be achieved for wells surrounded by multiple fractures for a given pressure drop. Similar to the single fracture near a well, a hump on the pressure-derivative curve can be found after transitional flow. To take advantage of fractures and weaken the effects of dynamic fracture conductivity in the boundary-dominated flow period, production during early-time radial flow and transitional flow periods becomes more important.
References
Steefel, C. I. & Lichtner, P. C. Multicomponent reactive transport in discrete fractures: I. Controls on reaction front geometry. J. Hydrol. 209(1), 186–199 (1998).
Cai, J., Wei, W., Hu, X., Liu, R. & Wang, J. Fractal characterization of dynamic fracture network extension in porous media. Fractals. 25(02), 1–11 (2017).
Ozkan, E., Brown, M. L., Raghavan, R. & Kazemi, H. Comparison of fractured-horizontal-well performance in tight sand and shale reservoirs. SPE Res. Eval. Eng. 14(02), 248–259 (2011).
Kuchuk, F., Biryukov, D. & Fitzpatrick, T. Fractured-reservoir modeling and interpretation. SPE J. 20(05), 983–1,004 (2015).
Eisen, M., Mokhtari, A. & Ribeiro, A. Decentralized quasi-newton methods. IEEE T. Signal Proces. 65(10), 2613–2628 (2017).
Gringarten, A. C. & Ramey Jr, H. J. The use of source and Green’s functions in solving unsteady-flow problems in reservoirs. SPE J. 13(05), 285–296 (1973).
Cinco, L., Samaniego, V. & Dominguez, A. Transient pressure behavior for a well with a finite-conductivity vertical fracture. SPE J. 18(04), 253–264 (1978).
Cinco, H. & Samaniego,V. F. Transient pressure analysis: Finite conductivity fracture case versus damaged fracture case. In SPE Annual Technical Conference and Exhibition, San Antonio, Texas, US. Society of Petroleum Engineers. https://doi.org/10.2118/10179-MS (1981, October 4-7).
Berumen, S., Tiab, D. & Rodriguez, F. Constant rate solutions for a fractured well with an asymmetric fracture. J. Pet. Sci. Eng. 25(1), 49–58 (2000).
Tiab, D. Analysis of pressure derivative data of hydraulically fractured wells by the Tiab’s Direct Synthesis technique. J. Pet. Sci. Eng. 49(1), 1–21 (2005).
Luo, W. & Tang, C. A semianalytical solution of a vertical fractured well with varying conductivity under non-Darcy-flow condition. SPE J. 20(05), 1028–1039 (2015).
Larsen, L. & Hegre, T. M. Pressure transient analysis of multifractured horizontal wells. In SPE Annual Technical Conference and Exhibition, New Orleans, Louisiana. Society of Petroleum Engineers. https://doi.org/10.2118/28389-MS (1994, September 25-28).
Crosby, D. G., Rahman, M. M., Rahman, M. K. & Rahman, S. S. Single and multiple transverse fracture initiation from horizontal wells. J. Pet. Sci. Eng. 35(3), 191–204 (2002).
Wan, J. & Aziz, K. Semi-analytical well model of horizontal wells with multiple hydraulic fractures. SPE J. 7(04), 437–445 (2002).
Wei, Y. & Economides, M. J. Transverse hydraulic fractures from a horizontal well. In SPE Annual Technical Conference and Exhibition. Dallas, Texas. Society of Petroleum Engineers. https://doi.org/10.2118/94671-MS (2005, October 9-12).
Medeiros, F., Kurtoglu, B., Ozkan, E. & Kazemi, H. Pressure-transient performances of hydraulically fractured horizontal wells in locally and globally naturally fractured formations. In International Petroleum Technology Conference, Dubai, U.A.E. International Petroleum Technology Conference. https://doi.org/10.2523/IPTC-11781-MS (2007, December 4-6).
Brown, M., Ozkan, E., Raghavan, R. & Kazemi, H. Practical solutions for pressure-transient responses of fractured horizontal wells in unconventional shale reservoirs. SPE Res. Eval. Eng. 14(06), 663–676 (2011).
Zhao, Y. L., Zhang, L. H., Zhao, J. Z., Luo, J. X. & Zhang, B. N. “Triple porosity” modeling of transient well test and rate decline analysis for multi-fractured horizontal well in shale gas reservoirs. J. Pet. Sci. Eng. 110, 253–262 (2013).
Yuan, B. et al. A new analytical multi-linear solution for gas flow toward fractured horizontal well with different fracture intensity. J. Nat. Gas Sci. Eng. 23, 227–238 (2015).
Givens, J. W. & Crawford, P. B. Effect of isolated vertical fractures existing in the reservoir on fluid displacement response. SPE J. 6(01), 81–86 (1966).
Huskey, W. L. & Crawford, P. B. Performance of petroleum reservoirs containing vertical fractures in the matrix. SPE J. 7(02), 221–228 (1967).
Cinco,L. H., Samaniego, F. V. & Dominguez, N. Unsteady state behavior for a well near a natural fracture. In SPE Annual Technical Conference and Exhibition, New Orleans, Louisiana. Society of Petroleum Engineers. https://doi.org/10.2118/6019-MS (1976, October 3-6).
Guo, G., Evans, R. D. & Chang, M. M. Pressure-transient behavior for a horizontal well intersecting multiple random discrete fractures.In SPE Annual Technical Conference and Exhibition, New Orleans, Louisiana. Society of Petroleum Engineers. https://doi.org/10.2118/28390-MS (1994, September 25-28).
Izadi, M. & Yildiz, T. Transient flow in discretely fractured porous media. SPE J. 14(02), 362–373 (2009).
Zeng, F., Zhao, G. & Liu, H. A new model for reservoirs with a discrete-fracture system. SPE J. 51(2), 127–136 (2012).
Biryukov, D. & Kuchuk, F. J. Transient pressure behavior of reservoirs with discrete conductive faults and fractures. Transp. Porous. Med. 95(1), 239–268 (2012).
Kuchuk, F. & Biryukov, D. Pressure-transient tests and flow regimes in fractured reservoirs. SPE Res. Eval. Eng. 18(02), 187–204 (2015).
Chen, S. M. & Evers, J. F. A stable numerical model for vertically fractured gas reservoir incorporating stress sensitivity. In SPE California Regional Meeting, Bakersfield, California. Society of Petroleum Engineers. https://doi.org/10.2118/9941-MS (1981, March 25-27).
Berumen, S. & Tiab, D. Effect of pore pressure on conductivity and permeability of fractured rocks. In SPE Western Regional Meeting, Anchorage, Alaska. Society of Petroleum Engineers. https://doi.org/10.2118/35694-MS (1996, May 22-24).
Pedroso, C. A. & Correa, A. C. F. A new model of a pressure-dependent-conductivity hydraulic fracture in a finite reservoir: constant rate production case. In Latin American and Caribbean Petroleum Engineering Conference, Rio de Janeiro, Brazil. Society of Petroleum Engineers. https://doi.org/10.2118/38976-MS (1997, August 30-September 3).
Cho, Y., Ozkan, E. & Apaydin, O. G. Pressure-dependent natural-fracture permeability in shale and its effect on shale-gas well production. SPE Res. Eval. Eng. 16(02), 216–228 (2013).
Zhang, Z., He, S., Liu, G. & Mo, S. Pressure buildup behavior of vertically fractured wells with stress-sensitive conductivity. J. Pet. Sci. Eng. 122, 48–55 (2014).
Wang, Y. & Aryana, S. Numerical investigation of stress-dependent fracture apertures and their spatial variations on production from unconventional gas reservoirs with complex fracture geometries. In SPE Low Perm Symposium, Denver, Colorado, USA Society of Petroleum Engineers. https://doi.org/10.2118/180244-MS (2016, May 5-6).
Luo, W. & Tang, C. Pressure-transient analysis of multiwing fractures connected to a vertical wellbore. SPE J. 20(02), 360–367 (2015).
Ozkan, E. & Raghavan, R. Some new solutions to solve problems in well test analysis: I–computational considerations and applications. SPE Formation Eval. 6(03), 359–368 (1991).
Ozkan, E., Yildiz, T. & Kuchuk, F. Transient pressure behavior of dual-lateral wells. SPE J. 3(02), 181–190 (1998).
Acknowledgements
This work was supported by the National Natural Science Foundation of China (Grant No. 51674227), the Fundamental Research Funds for the Central Universities of China (2-9-2017-310) and the Science and Technology Special Funds of China for 2016ZX05015-002.
Author information
Authors and Affiliations
Contributions
As the first author, W. Luo established the novel mathematical model and wrote the main manuscript text. As the corresponding author, P. Liu have made substantial contributions to the conception/design of the work; I have approved the final version to be published; AND I agree to be accountable for all aspects of the work in ensuring that questions related to the accuracy or integrity of any part of the work are appropriately investigated. Q. Tian solved mathematical model and prepared all of the figures. C. Tang designed the computer program. Y. Zhou revised the manuscript text. All authors discussed the results and critically reviewed the manuscript.
Corresponding author
Ethics declarations
Competing Interests
The authors declare that they have no competing interests.
Additional information
Publisher's note: Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Electronic supplementary material
Rights and permissions
Open Access This article is licensed under a Creative Commons Attribution 4.0 International License, which permits use, sharing, adaptation, distribution and reproduction in any medium or format, as long as you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons license, and indicate if changes were made. The images or other third party material in this article are included in the article’s Creative Commons license, unless indicated otherwise in a credit line to the material. If material is not included in the article’s Creative Commons license and your intended use is not permitted by statutory regulation or exceeds the permitted use, you will need to obtain permission directly from the copyright holder. To view a copy of this license, visit http://creativecommons.org/licenses/by/4.0/.
About this article
Cite this article
Luo, W., Liu, P., Tian, Q. et al. Effects of discrete dynamic-conductivity fractures on the transient pressure of a vertical well in a closed rectangular reservoir. Sci Rep 7, 15537 (2017). https://doi.org/10.1038/s41598-017-15785-9
Received:
Accepted:
Published:
DOI: https://doi.org/10.1038/s41598-017-15785-9
Comments
By submitting a comment you agree to abide by our Terms and Community Guidelines. If you find something abusive or that does not comply with our terms or guidelines please flag it as inappropriate.