Abstract
Self-assembly of artificial nanoscale units into superstructures is a prevalent topic in science. In biomimicry, scientists attempt to develop artificial self-assembled nanoarchitectures. However, despite extensive efforts, the preparation of nanoarchitectures with superior physical properties remains a challenge. For example, one of the major topics in the field of molecular magnetism is the development of high-spin (HS) molecules. Here, we report a cyanide-bridged magnetic nanocage composed of 18 HS iron(III) ions and 24 low-spin iron(II) ions. The magnetic iron(III) centres are ferromagnetically coupled, yielding the highest ground-state spin number (S=45) of any molecule reported to date.
Similar content being viewed by others
Introduction
Self-assembled highly symmetric nanostructures are commonplaces in nature: for example, the icosahedra of virus capsids and the cuboctahedra of magnetite nanocrystals in magnetotactic bacteria. Following nature’s lead, attempts to prepare self-assembled discrete molecular architectures constructed through the coordination of metal ions and organic ligands such as metal–organic polyhedra have captivated many scientists’ attention1,2,3,4,5,6,7,8,9,10. The unique structural and electronic configurations, resulting from the combined features of both metal ions and organic molecules, can give way to diverse functional properties for many applications, such as molecular flasks11, catalysis12, ion channels13, sensors14, drug delivery systems15, nanomagnets16,17,18 including prototypes for quantum information processing19,20 and gas storage devices21,22,23,24.
One of the challenges in the field of molecular magnetism is to synthetically prepare new nanoarchitectures with high-ground state spin numbers. To date, numerous high-spin (HS) molecules have been reported25,26. Here, we report a giant-spin nanocage that contains 18 HS ferromagnetically coupled FeIII(S=5/2) ions resulting in a molecular ground state spin of S=45, the largest value known to date27. This nanoarchitecture is a mixed valent HS and low-spin (LS) cyano-bridged FeIII-HS18FeII-LS24 compound, structured as a supramolecular cage with a nanometre-sized inner cavity space.
Results
Preparation of Fe42 cyanide-bridged nanocage
The strategy used to construct the magnetic nanocage is based on the preparation of metal–organic polyhedra28. We used metal–organic complexes as building blocks, which not only act as caps but also contain metal centres and cyano groups that enable the introduction of magnetic interactions. Namely, instead of organic tridentate pyridyl ligands, which can provide a large hollow polyhedral structure, we used monoanionic complex ligand {Fe(Tp)(CN)3}− (Tp=hydrotris(pyrazolyl)borate) units29,30,31 as a trinucleating ligand of the metal ions for constructing magnetic nanocage. In addition, the choice of counter metal ions in these structures importantly enables the adjustment of their magnetic properties, facilitating the creation of HS ground states. We employed iron ions in consideration of the magnetic interaction and redox activity of the ferromagnetic metal–cyanide compound: Prussian blue FeIII4[FeII(CN)6]3·xH2O (refs 16, 32). The reaction of Fe(CF3SO3)2, 1,3-di(4-pyridyl)propane (dpp), L-ascorbic acid and Li[Fe(Tp)(CN)3] in H2O led to the isolation of a new [FeIII18FeII24] spin nanocage: [{Fe(Tp)(CN)3}24{Fe(H2O)2}6{Fe(dpp)(H2O)}12(CF3SO3)6]·18H2O (1·18H2O) as green cubic crystals (Supplementary Fig. 1), where 1 contains 42 iron ions, the largest number of metal centres in any cyano-bridged cluster reported to date33.
Characterization of Fe42 cyanide-bridged nanocage
Crystallographic analysis of 1·18H2O reveals that each octahedral {Fe(Tp)(CN)3} unit is connected to three Fe ions by three cyanide anions. The Fe ions are further ligated by water and dpp to give octahedral {Fe(NC)4(H2O)2} and {Fe(NC)4(dpp)(H2O)} coordination spheres, where the Fe centres are in a weakly distorted octahedral environment with axial water molecules (Fig. 1 and Supplementary Tables 1–3). Thus, 24 {Fe(Tp)(CN)3}, 12 {Fe(NC)4(dpp)(H2O)} and 6 {Fe(NC)4(H2O)2} building units are symmetrically disposed in an O space around a central point providing the cube cage, with a separation of 1.96 nm between the most distant Fe ions. Six severely disordered, charge-balancing trifluoromethanesulfonate anions are apparent outside the cationic [Fe42]6+ nanocages, keeping them well separated, and 18 solvent water molecules are located inside the cage.
The 57Fe Mössbauer spectrum measured for 1·18H2O at 298 K can be deconvoluted into two doublets exhibiting quadrupole splitting (LS-FeII:δ (isomer shift)=0.065 mm s−1, Δ (quadrupole splitting)=0.47 mm s−1; HS-FeIII: δ=0.43 mm s−1 and Δ=0.71 mm s−1) in a relative intensity ratio of FeII/FeIII=0.55/0.45 Supplementary Fig. 2 and Supplementary Table 4). Charge considerations and Mössbauer spectroscopic measurements suggest that 1·18H2O has 24 FeII-LS ions, to which the cyanide carbon atoms coordinate, and 18 FeIII-HS ions at room temperature. Note that 1·18H2O was prepared using {FeIII(Tp)(CN)3}− as a starting material, where the cyanide carbon atoms are coordinated to FeIII ions. Electron transfer from FeII ions to the {FeIII(Tp)(CN)3}− units is, therefore, suggested to occur during the reaction, leading to an FeII-LS–CN–FeIII-HS linkage. Further, evidence of this linkage was obtained by synchrotron X-ray absorption spectroscopy (XAS) at the Fe L-edge. Comparison of XAS for 1·18H2O with variants of the starting material compound, Li[FeIII-LS(Tp)(CN)3] and K2[FeII-LS(Tp)(CN)3], infers that the valence composition of the 24 {Fe(Tp)(CN)3} is consistent with {FeII-LS(Tp)(CN)3}2− (See Supplementary Fig. 3, with further details of this measurement).
The most remarkable structural feature of 1·18H2O is that the 18 FeIII-HS ions can be identified as the vertices of a highly symmetric entity shown in Fig. 2. First, 12 FeIII-HS centres in {Fe(NC)4(dpp)(H2O)} units are defined as the vertices of cuboctahedron, all of whose sides have a length of 7.85 Å. Second, six square windows of the cuboctahedron are stellated with 24 isosceles triangles, each with side lengths of 6.83, 6.83 and 7.85 Å, with six vertices defined by FeIII-HS ions from {Fe(NC)4(H2O)2} units34,35. The FeII–CN–FeIII linkage of 1·18H2O classify it as a Prussian blue analogue36,37 from the standpoint of its electronic state. Prussian blue analogues exhibit in a molecule-based framework with cyanide-bridging akin to the three-dimensional Prussian blue compound FeIII4[FeII(CN)6]3·xH2O. Prussian blue shows ferromagnetic behaviour with a Curie temperature Tc of 5.5±0.5 K (ref. 32). The observed ferromagnetism involves a long-range order of the FeIII ions. While 1·18H2O is much more complex than FeIII4[FeII(CN)6]3·xH2O, the cyanide bridging units between the FeIII ions are similar. The shortest FeIII–FeIII distances for Prussian blue and 1·18H2O are 7.2 Å and 6.8 Å through space and 10.2 Å and 9.9 Å along the FeIII–NC–FeII–CN–FeIII units, respectively. Accordingly, it is reasonable that the 18 FeIII-HS (S=5/2) ions, at the vertices in 1·18H2O, are coupled ferromagnetically.
Magnetic properties of Fe42 cyanide-bridged nanocage
Figure 3a shows the magnetic properties of a polycrystalline sample of 1·18H2O under a direct current field of 10 kOe from 300 to 30 K and 100 Oe from 30 to 2 K. It indicates the existence of predominantly ferromagnetic interactions and a resulting giant ground-state spin for 1·18H2O. At 300 K, the χmT product is 85.5 cm3 mol−1 K, and the data in the range 300–30 K can be fitted to the Curie–Weiss law, yielding C=83.2 cm3 mol−1 K and θ=+6.7 K. This C value is consistent with the expectations (78.8 cm3 mol−1 K with g=2.0) for 18 uncoupled FeIII centres (S=5/2). On cooling, the χmT value becomes slightly larger with temperature, abruptly increasing to 863 cm3 mol−1 K at 2 K (Supplementary Fig. 4). This magnetic behaviour and the positive Weiss constant suggest the existence of dominant ferromagnetic exchange interactions in 1·18H2O. Figure 3b shows χ−1 versus the T-plot for various applied fields, which displays an inflection in χ−1 between 10 and 5 K as excited states depopulate, on further cooling below 5 K the slope starts to become linear again, suggesting that it is just the ground state that is mainly populated, following the dependence of a paramagnetic S=45, g=2.0, spin unit (dot line).
Moreover, the magnetization (M) at 2 K (Fig. 3c) rapidly increases at low fields, and then steadily increases with H>15 kOe to reach a near saturation value of 88.4 μB at 50 kOe, which is in good agreement with the expected value of 90 μB (with g=2.0) for a ground state of ST=90/2 (Supplementary Figs 5 and 6). This magnetization behaviour is significantly higher than the Brillouin curve corresponding to 18 non-interacting SFe spins (S=5/2, green line), fitting more closely the Brillouin curve for one S=45 centre (with g=2.0, blue line, see Methods). These data support the maximum possible spin state, S=45, which is the largest spin ground state number of any molecule ever prepared27.
To rule out the possibility of intermolecular interaction or a magnetic ordering between the molecule-based giant spins, electron paramagnetic resonance (EPR) spectra of 1·18H2O have been examined. Figure 3d shows no evidence of intermolecular interaction is present within EPR on decrease of temperature to 1.6 K; the g=2.0 absorption increases in intensity with no significant variation of line width or shift in resonance field position to evidence intermolecular interactions. No evidence of anisotropy is observed in EPR measurements, it is reasoned that the geometry of the molecular structure of 1·18H2O causes the cancelling of single ion anisotropic contributions. In addition, the temperature dependence of magnetization for 1·18H2O under various applied magnetic fields does not show evidence of spontaneous magnetization down to 0.5 K (see Supplementary Fig. 7). These results indicate that the cyanide-bridged magnetic Fe42 nanocage exhibits the maximum spin ground state with isolated molecule S=45.
Discussion
DFT calculations were carried out to estimate changes in the electronic structures of 1·18H2O. Calculations were simplified to a cyano-bridged molecular square38,39 formulated as [FeII2–CN–FeIII2] with a Tp− ligand on the FeII ion, a pyridine ligand, and H2O on the FeIII ion (Fig. 4, and Supplementary Tables 5–7). Figure 4 shows HS ferromagnetic (HSFM) state was the ground state, and LS ferromagnetic (LSFM) and antiferromagnetic (LSAF) states were above 5.5 kcal mol−1 and 1.5 kcal mol−1, respectively. DFT calculations indicate the ferromagnetic character of a magnetic coupling between the two diagonal FeIII-HS ions in the square framework. The calculated J value (35.5 cm−1 at the B3LYP* level) for the tetranuclear cyano-bridged square complex overestimates the magnitude of the exchange coupling parameters. The overestimation of coupling constants by a factor of 2–4 is not unusual in DFT calculations40,41. The calculation predicts the correct sign for J corresponding to the ferromagnetic nature of the ground state in the [Fe42] nanocage.
We have presented a Fe42 cyanide-bridged nanocage with a HS framework. Many metal–cyanide clusters have been synthesized since the discovery of Prussian blue. Our metal–cyanide polyhedron is the largest cyanide-bridged polynuclear cluster and exhibits a rare hollow structure. Among the various morphologies of nanoarchitectures, hollow spheres are of great interest because of their high surface to volume ratio and large pore volume, which could be exploited for promising applications in the controlled encapsulation and release of molecules.
In summary, we report a new high-nuclearity iron complex with a HS framework. In the Fe42 cyanide-bridged nanocage, magnetic metal centres are ferromagnetically coupled, yielding the highest ground state spin number (S=45) of any prepared molecule.
Methods
Synthesis of Fe42 cyanide-bridged nanocage
[{Fe(Tp)(CN)3}24{Fe(H2O)2}6{Fe(dpp)(H2O)}12(CF3SO3)6]·18H2O: 1·18H2O.
A 1 ml aqueous solution of 17 μmol of Li[Fe(Tp)(CN)3] and 8.3 μmol of 1,3-di(4-pyridyl)propane was slowly layered over a 2 ml aqueous solution of 8.3 μmol of Fe(CF3SO3)2 and 1.7 μmol of L-ascorbic acid with H2O (1 ml) as a middle buffer layer under an aerobic condition. Crystallization required several weeks and gave crystals in 30% yield based on Li[Fe(Tp)(CN)3]. The crystals were washed with H2O and dried under reduced pressure for 12 h. As prepared compound, before vacuum drying, has approximately 50H2O molecules inside the cage (compound 1·ca 50H2O), which become partially desolvated when exposed to air at room temperature. Therefore, the physical measurements performed on compound 1·18H2O were prepared carefully to prevent desolvation. The reported structures have been characterized by the single-crystal X-ray crystallography (Supplementary Tables 1–3 and Supplementary Data 1 and 2).
Elemental analysis
Elemental analysis for C450H492B24F18Fe42N240O60S6 (1·18H2O) is as follows: calculated (found) C, 40.45 (40.65); H, 3.71 (3.54) and N, 25.16 (25.30). Inductively coupled plasma atomic emission spectroscopy (ICP-AES) analysis was performed to measure the Fe content in the solid sample of 1·18H2O. ICP-AES analysis shows that the Fe contents in 1·18H2O is 16 wt%, which is in good agreement with the calculated value of 16.8 wt%. In addition, analysis of the sulfur content of 1·18H2O with total sulfur analyser (TOX-100) reveals the sulfur content is 1.6 wt% (calcd. 1.4 wt%).
X-ray structure determination
Single-crystal synchrotron radiation X-ray diffraction experiments were performed at 295 K for 1·18H2O, and 100 K for 1·ca 50H2O using a Rigaku Mercury2 CCD detector at BL02B1/SPring-8 (Hyogo, Japan). The wavelength of the incident X-ray was 0.6186 or 0.6202 Å. We used anomalous dispersion coefficients for structure refinement, f′ and f″, in dependence on X-ray energy calculated on the original FPRIME code of Cromer.
SEM measurements
Scanning electron microscopy studies were performed with a Hitachi Ultra-high Resolution Scanning Electron Microscope SU8000.
Physical measurements
Magnetic susceptibility measurements of samples were performed on a Quantum Design SQUID (MPMS XL-5 and MPMS XL-7) magnetometer. To prevent the loss of uncoordinated water molecules, the sample was introduced directly into the sample chamber at 100 K without purging, while flowing He gas. Keep the sample stay at 100 K for several minutes and then purge the chamber. At the end, vent the sample space with He gas and start the measurement. Data were corrected for the diamagnetic contribution calculated from Pascal constants. The Mössbauer spectra (isomer shift versus metallic iron at room temperature) were measured using a Wissel MVT-1000 Mössbauer spectrometer with a 57Co/Rh source in the transmission mode. All isomer shifts are given relative to α-Fe at room temperature. EPR measurements were performed with the Terahertz ESR Apparatus (TESRA-IMR) installed in the magnetism division of Institute of Materials Research (IMR), Tohoku University. A solenoid magnet is fed by a 90-kJ capacitor bank delivering a field pulse of 25 ms in width. Applied fields from 0 to 30 T were investigated for a range of EPR microwave frequencies from 90 to 405 GHz generated by backward-travelling wave oscillators. Measurements were performed in a He4 cryostat down to 1.6 K.
Simulation of magnetization process
The magnetization curve was compared with the mean-field simulation assuming an HDVV (Heisenberg–Dirac–Van Vleck)-type spin Hamiltonian: Ĥ=−2J∑(i,j)Ŝi·Ŝj, where a uniform isotropic exchange parameter J makes all the pair of S=5/2 spins coupled. This Hamiltonian gives the energy eigenvalues E(Stotal)=−J {Stotal (Stotal+1) −18s(s+1)} with the resultant spin of the molecule Stotal, and the magnetic susceptibility is easily calculated following the Van Vleck formula. The simulation curve with a ferromagnetic coupling zJ/kB=+0.5 K (z=17) and g factor of 2.0 agreed well with the experimental values.
XAS measurements
X-ray absorption spectra were measured on the soft X-ray undulator beam-line BL25SU at Spring 8, Japan. Soft X-rays circularly polarized from a twin helical undulator were monochromated and focused onto a thin polycrystalline layer of 1·18H2O. The measured sample was fixed with carbon tape to a sapphire sample holder. X-ray absorption spectra were measured by the total electron yield method in which the sample current is directly measured while scanning the photon energy. Measurements were performed at zero applied magnetic field and hence both positive and negative X-ray helices resulted in equivalent absorption spectra. The sample chamber for the soft XAS keeps a high vacuum of 10−5 Pa or the better. Measurements of 1·18H2O were repeated incrementally over several days and were found not to exhibit changes in spectral line shape with respect to the time spent under vacuum. Care was taken during XAS measurements to control the effect of photoreduction. The incident beam intensity was incrementally reduced until consistent multiple measurements at the same sample spot were obtained after an intensity reduction to 7%. To ensure damage was not encountered in short time periods, rapid measurements over defined features of the L3 edge were measured repeatedly and ensured to be coincident.
DFT calculation
Full details of computational method are given in the Supplementary Methods.
Additional information
How to cite this article: Kang, S. et al. A ferromagnetically coupled Fe42 cyanide-bridged nanocage. Nat. Commun. 6:5955 doi: 10.1038/ncomms6955 (2015).
Accession codes: The X-ray crystallographic coordinates for structures reported in this Article have been deposited at the Cambridge Crystallographic Data Centre (CCDC), under deposition number CCDC 932131 and 932133. These data can be obtained free of charge from The Cambridge Crystallographic Data Centre via www.ccdc.cam.ac.uk/data_request/cif.
References
Olenyuk, B., Whiteford, J. A., Fechtenkotter, A. & Stang, P. J. Self-assembly of nanoscale cuboctahedra by coordination chemistry. Nature 398, 796–799 (1999).
Takeda, N., Umemoto, K., Yamaguchi, K. & Fujita, M. A nanometre-sized hexahedral coordination capsule assembled from 24 components. Nature 398, 794–796 (1999).
O'Keeffe, M. & Yaghi, O. M. Deconstructing the crystal structures of metal-organic frameworks and related materials into their underlying nets. Chem. Rev. 112, 675–702 (2012).
Sun, Q. F. et al. Self-assembled M24L48 polyhedra and their sharp structural switch upon subtle ligand variation. Science 328, 1144–1147 (2010).
Chichak, K. S. et al. Molecular borromean rings. Science 304, 1308–1312 (2004).
Bunzen, J. et al. Self-assembly of M24L48 polyhedra based on empirical prediction. Angew. Chem. Int. Ed. 51, 3161–3163 (2012).
Tranchemontagne, D. J., Ni, Z., O'Keeffe, M. & Yaghi, O. M. Reticular chemistry of metal-organic polyhedra. Angew. Chem. Int. Ed. 47, 5136–5147 (2008).
An, J. et al. Metal-adeninate vertices for the construction of an exceptionally porous metal-organic framework. Nat. Commun. 3, 604 (2012).
Liu, Y., Hu, C., Comotti, A. & Ward, M. D. Supramolecular Archimedean cages assembled with 72 hydrogen bonds. Science 333, 436–440 (2011).
Riddell, I. A. et al. Anion-induced reconstitution of a self-assembling system to express a chloride-binding Co10L15 pentagonal prism. Nat. Chem. 4, 751–756 (2012).
Yoshizawa, M., Klosterman, J. K. & Fujita, M. Functional molecular flasks: new properties and reactions within discrete, self-assembled hosts. Angew. Chem. Int. Ed. 48, 3418–3438 (2009).
Pluth, M. D., Bergman, R. G. & Raymond, K. N. Acid catalysis in basic solution: a supramolecular host promotes orthoformate hydrolysis. Science 316, 85–88 (2007).
Jung, M., Kim, H., Baek, K. & Kim, K. Synthetic ion channel based on metal-organic polyhedra. Angew. Chem. Int. Ed. 47, 5755–5757 (2008).
Wang, J., He, C., Wu, P., Wang, J. & Duan, C. An amide-containing metal-organic tetrahedron responding to a spin-trapping reaction in a fluorescent enhancement manner for biological imaging of NO in living cells. J. Am. Chem. Soc. 133, 12402–12405 (2011).
Wang, H. N. et al. Stepwise assembly of metal-organic framework based on a metal-organic polyhedron precursor for drug delivery. Chem. Commun. 47, 7128–7130 (2011).
Beltran, L. M. & Long, J. R. Directed assembly of metal-cyanide cluster magnets. Acc. Chem. Res. 38, 325–334 (2005).
Li, D. et al. Magnetic and optical bistability driven by thermally and photoinduced intramolecular electron transfer in a molecular cobalt-iron prussian blue analogue. J. Am. Chem. Soc. 130, 252–258 (2008).
Gatteschi, D., Sessoli, R. & Villain, J. Molecular nanomagnets Oxford Univ. Press (2006).
Leuenberger, M. N. & Loss, D. Quantum computing in molecular magnets. Nature 410, 789–793 (2001).
Troiani, F. et al. Molecular engineering of antiferromagnetic rings for quantum computation. Phys. Rev. Lett. 94, 207208 (2005).
Sudik, A. C. et al. Design, synthesis, structure, and gas (N2, Ar, CO2, CH4, and H2) sorption properties of porous metal-organic tetrahedral and heterocuboidal polyhedra. J. Am. Chem. Soc. 127, 7110–7118 (2005).
Duriska, M. B. et al. Systematic metal variation and solvent and hydrogen-gas storage in supramolecular nanoballs. Angew. Chem. Int. Ed. 48, 8919–8922 (2009).
Farha, O. K. et al. Metal–organic framework materials with ultrahigh surface areas: is the sky the limit? J. Am. Chem. Soc. 134, 15016–15021 (2012).
Farha, O. K. et al. De novo synthesis of a metal–organic framework material featuring ultrahigh surface area and gas storage capacities. Nat. Chem. 2, 944–948 (2010).
Launay, J. P. & Verdaguer, M. Electrons in Molecules: From Basic Principles to Molecular Electronics Oxford Univ. Press (2013).
Pedersen, K. S., Bendix, J. & Clérac, R. Single-molecule magnet engineering: building-block approaches. Chem. Commun. 50, 4396–4415 (2014).
Ako, A. M. et al. A ferromagnetically coupled Mn19 aggregate with a record S=83/2 ground spin state. Angew. Chem. Int. Ed. 45, 4926–4929 (2006).
Cook, T. R., Zheng, Y. R. & Stang, P. J. Metal-organic frameworks and self-assembled supramolecular coordination complexes: comparing and contrasting the design, synthesis, and functionality of metal-organic materials. Chem. Rev. 113, 734–777 (2013).
Lescouezec, R., Vaissermann, J., Lloret, F., Julve, M. & Verdaguer, M. Ferromagnetic coupling between low- and high-spin iron(III) ions in the tetranuclear complex fac-[[FeIII[HB(pz)3](CN)2(μ-CN)]3FeIII(H2O)3]* 6H2O ([HB(pz)3]−=hydrotris(1-pyrazolyl)borate. Inorg. Chem. 41, 5943–5945 (2002).
Wang, S. et al. [(Tp8(H2O)6Cu(II)6Fe(III)8(CN)24]4+: a cyanide-bridged face-centered-cubic cluster with single-molecule-magnet behavior. Angew. Chem. Int. Ed. 43, 5940–5943 (2004).
Wang, S., Ding, X. H., Zuo, J. L., You, X. Z. & Huang, W. Tricyanometalate molecular chemistry: A type of versatile building blocks for the construction of cyano-bridged molecular architectures. Coord. Chem. Rev. 255, 1713–1732 (2011).
Ito, A., Suenaga, M. & Ono, K. Mösbauer study of soluble Prussian blue, insoluble Prussian blue, and Turnbull's blue. J. Chem. Phys. 48, 3597–3599 (1968).
Wang, X. Y., Prosvirin, A. V. & Dunbar, K. R. A docosanuclear {Mo8Mn14} cluster based on [Mo(CN)7]4−. Angew. Chem. Int. Ed. 49, 5081–5084 (2010).
Sun, Q. F., Sato, S. & Fujita, M. An M18L24 stellated cuboctahedron through post-stellation of an M12L24 core. Nat. Chem. 4, 330–333 (2012).
Milway, V. A. et al. Directed Synthesis of {Mn18Cu6} Heterometallic Complexes. Angew. Chem. Int. Ed. 52, 1949–1952 (2013).
Ferlay, S., Mallah, T., Ouahes, R., Veillet, P. & Verdaguer, M. Nature 378, 701–703 (1995).
Hoshino, N. et al. Three-way switching in a cyanide-bridged [CoFe] chain. Nat. Chem. 4, 921–926 (2012).
Mondal, A. et al. Photomagnetic effect in a cyanide-bridged mixed-valence Fe2IIFe2III molecular square. Chem. Commun. 48, 5653–5655 (2012).
Zhang, Y. et al. Reversible thermally and photoinduced electron transfer in a cyano-bridged {Fe2Co2} square complex. Angew. Chem. Int. Ed. 49, 3752–3756 (2010).
Brunold, T. C., Tamura, N., Kitajima, N., Moro-oka, Y. & Solomon, E. I. Spectroscopic study of [Fe2(O2)(OBz)2{HB(pz')3}2]: nature of the μ-1,2 peroxide−Fe(III) bond and its possible relevance to O2 activation by non-heme iron enzymes. J. Am. Chem. Soc. 120, 5674–5690 (1998).
Binning, R. C. Jr & Bacelo, D. E. High-spin versus broken symmetry—effect of DFT spin density representation on the geometries of three diiron (III) model compounds. J. Comput. Chem. 29, 716–723 (2007).
Acknowledgements
This work was supported by JSPS KAKENHI Grant Number 25109533, 24109014, 24790061, 26810039 and the Mitsubishi Foundation, and Network Joint Research Center for Materials and Devices, and the NSFC (Grant 21421005, 91122031, 21322103). M.L.B. thanks the JSPS for a post-doctoral fellowship. This work was partly performed as the Inter-university Cooperative Research Program of IMR, Tohoku Univ. This work was partly supported by Nanotechnology Platform Program (Molecule and Material Synthesis) of the Ministry of Education, Culture, Sports, Science and Technology (MEXT), Japan. The synchrotron radiation experiments were performed at the BL02B1 and BL25SU of SPring-8 with the approval of the Japan Synchrotron Radiation Research Institute (JASRI) (Proposal No. 2012B1582, 2013B1032, and 2013A1127) and at the beam-line BL10 of the SAGA Light Source with the approval of the Kyushu Synchrotron Light Research Center (Proposal No. 1304028PT).
Author information
Authors and Affiliations
Contributions
T.L. and C.D. in Dalian and O.S. in Fukuoka conceived and supervised the project. S. Kang, K.H., S. Kanegawa and H.Z. planed, implemented materials synthesis and characterization and analysed the magnetic measurements data. K.S. finalized the synchrotron X-ray data. Y.S. and K.Y. contributed to the DFT calculation. S.H. performed the Mössbauer measurement. M.N. and M.M. contributed to analyses of the magnetic susceptibility. M.L.B. and H.N. were responsible for experiments performed in large magnetic fields and XAS measurements. T.N. contributed to the XAS experiments. S. Kang, Y.S., L.T. and O.S. wrote the manuscript. All authors discussed the results and commented on the manuscript. S. Kang, and H.Z. contributed to this work equally.
Corresponding authors
Ethics declarations
Competing interests
The authors declare no competing financial interests.
Supplementary information
Supplementary Figures, Supplementary Tables, Supplementary Methods and Supplementary References.
Supplementary Figures 1-6, Supplementary Tables 1-7, Supplementary Methods and Supplementary References (PDF 928 kb)
Supplementary Data 1
Single crystal structure of 1•18H2O measured at 295 K (CIF 50 kb)
Supplementary Data 2
Single crystal structure of 1·ca.50H2O (single crystal structure of as prepared sample) measured at 100 K (CIF 50 kb)
Rights and permissions
This work is licensed under a Creative Commons Attribution 4.0 International License. The images or other third party material in this article are included in the article’s Creative Commons license, unless indicated otherwise in the credit line; if the material is not included under the Creative Commons license, users will need to obtain permission from the license holder to reproduce the material. To view a copy of this license, visit http://creativecommons.org/licenses/by/4.0/
About this article
Cite this article
Kang, S., Zheng, H., Liu, T. et al. A ferromagnetically coupled Fe42 cyanide-bridged nanocage. Nat Commun 6, 5955 (2015). https://doi.org/10.1038/ncomms6955
Received:
Accepted:
Published:
DOI: https://doi.org/10.1038/ncomms6955
This article is cited by
-
Application of THz ESR on Artificial Giant Spins in Magnetic Molecules
Applied Magnetic Resonance (2021)
-
Temperature dependence of spherical electron transfer in a nanosized [Fe14] complex
Nature Communications (2019)
-
Quantum Monte Carlo simulations of a giant {Ni21Gd20} cage with a S = 91 spin ground state
Nature Communications (2018)
-
Exchange Interactions on the Highest-Spin Reported Molecule: the Mixed-Valence Fe42 Complex
Scientific Reports (2016)
Comments
By submitting a comment you agree to abide by our Terms and Community Guidelines. If you find something abusive or that does not comply with our terms or guidelines please flag it as inappropriate.