Abstract
Slow light has been widely utilized to obtain enhanced nonlinearities, enhanced spontaneous emissions and increased phase shifts owing to its ability to promote light–matter interactions. By incorporating a graphene on a slow-light silicon photonic crystal waveguide, here we experimentally demonstrate an energy-efficient graphene microheater with a tuning efficiency of 1.07 nmmW−1 and power consumption per free spectral range of 3.99 mW. The rise and decay times (10–90%) are only 750 and 525 ns, which, to the best of our knowledge, are the fastest reported response times for microheaters in silicon photonics. The corresponding figure of merit of the device is 2.543 nW s, one order of magnitude better than results reported in previous studies. The influence of the length and shape of the graphene heater to the tuning efficiency is further investigated, providing valuable guidelines for enhancing the tuning efficiency of the graphene microheater.
Similar content being viewed by others
Introduction
Following several decades of explosive growth, the information industry has become a major energy consumer owing to the high power consumption by data centres1. As one of the most promising candidates for satisfying the comprehensive information industry requirements of low energy consumption, speed, bandwidth, density and cost, integrated silicon photonics2,3,4,5 have made rapid progress in a wide range of functionalities such as modulators6,7, photodetectors8,9,10 and optical switches11. This is largely enabled by silicon’s low loss, low cost and high fabrication compatibility with complementary metal-oxide semiconductor (CMOS) technology12,13. One of the most important properties of integrated devices in versatile and reconfigurable photonic networks is highly energy-efficient tunability with a fast response time. Owing to the relatively high thermo-optic coefficient of silicon (∼1.8 × 10−4 K−1)14, thermal tuning is often applied using a metallic microheater on a silicon waveguide in tunable silicon micro-ring resonators15 or Mach-Zehnder interferometers16 (MZIs). However, to avoid the light-absorption loss induced by the metal, a thick silicon dioxide (SiO2) layer is typically introduced between the silicon waveguide and the metallic heater, inevitably impeding heat transport and dissipation owing to the low thermal conductivity of SiO2 (1.44 W m−1 K−1)17. Several methods, such as the use of free-standing waveguide structures18,19 and different doping levels of the waveguide20, have been proposed to simultaneously obtain lower power consumption and a faster response time. However, free-standing waveguides may lack mechanical stability, and the tuning efficiency of different silicon waveguide doping is as low as 0.12 nm mW−1 (ref. 20).
The use of slow light in silicon photonic crystal waveguides (PhCWs) offers an approach for significantly improving the inherently weak light–matter interaction on nanometer-scale chips. By decreasing the group velocity of the transmitted light in periodic media21,22,23, slow light has been utilized in various applications such as sensors24, amplifiers25 and nonlinear optics26. Meanwhile, owing to many unique properties, such as a zero-band gap and tunable Fermi level27,28, high carrier mobility29,30 and ultra-broad absorption bandwidth31, graphene has been widely merged with nanophotonic structures to enhance the light–matter interaction32,33,34,35. In addition to these broadly studied applications, the use of graphene as a heating material36,37,38 in close contact to the silicon waveguide can significantly improve the tuning efficiency due to graphene’s low optical absorption rate39. Moreover, owing to the extremely high thermal conductivity of up to 5,300 W m−1 K−1, response times can be greatly reduced relative to devices with thick SiO2 cladding between the metallic heater and the waveguides. However, the current performances of devices using graphene heaters are limited either by their relatively high power consumptions37 or by their microsecond response times38.
In this study, we propose and demonstrate a new concept of enhancing the heater efficiency by the use of slow light in a PhCW with an added layer of graphene working as a heater. Here, graphene can efficiently heat the silicon slow-light photonic crystal, without otherwise perturbing the waveguide and thus jeopardizing the optical performance of the waveguide itself. The active tuning of group velocity in the PhCW has been studied before23, and here we explore how the slow-light effect in the PhCW can reduce the power consumption. The low optical loss in graphene gives us freedom to optimize the shape of the graphene heater in order to maximize the tuning efficiency, which is significantly different from previous work. We systemically investigate the influence of the graphene–PhCW interaction length and the shape of the graphene heaters on the tuning efficiency. The proposed slow-light-enhanced graphene microheaters show promising potential for applications in integrated silicon building blocks such as tunable phase shifters and filters that demand low power consumption, a fast response time, and CMOS-compatible fabrication processes.
Results
Design of the slow-light-enhanced graphene microheater
A schematic of the slow-light-enhanced graphene microheater is shown in Fig. 1a. A graphene monolayer is deposited onto the core region of the silicon PhCW. The graphene is contacted by two gold/titanium (Au/Ti) pads, exploiting the low contact resistance between Ti and graphene40. Ohmic heating is generated in the graphene via an applied voltage bias between the Au/Ti pads. The width of the graphene overlapping the photonic crystal line defect is designed to be narrower than the other part of the graphene to locally increase the Ohmic dissipation. This results in more effective heating, which will be discussed in the Discussion section.
The slow light can enhance the tuning efficiency owing to the large group index that can be obtained in the PhCW, which increases the effective interaction length between the heater and the waveguides22, thus increasing the corresponding phase shift. With the aid of perturbation theory41, the phase shift Δϕ induced by the heating can be expressed as (Supplementary Note 6),
where ω is the angular frequency of the light, ng is the group index of the PhCW, is the filling fraction defining the fraction of the optical field confined in silicon, L is the graphene–PhCW overlap length, a is the thermo-optic coefficient, ΔT is the temperature increase caused by the graphene heater and nSi is the refractive index of silicon, respectively. equation (1) shows how the phase shift (or heating efficiency) benefits from the slow light. The heating efficiency is proportional to the temperature increase (ΔT), which can be optimized by patterning the graphene heater. A longer PhCW can also reduce the power consumption but will increase the insertion loss and the size of the device. The high group index (larger than ∼40) of the PhCW can only be achieved near the fundamental mode cutoff in a very narrow bandwidth where large insertion losses21 are typical because slow-light promotes further damping42. Therefore, the band structure of the PhCW employed here should be carefully optimized to reach a relatively high group index, large bandwidth and low loss in the wavelength regime of interest. These requirements can be satisfied simultaneously using semi-slow-light PhCWs43,44.
The dispersion relationship of the PhCW is analysed using the plane-wave-expansion method45. To obtain a high group index with a large bandwidth, the positions of the first and second rows of holes adjacent to the line-defect are slightly tuned in a W1-type PhCW. The dispersion relationship of the PhCW is presented as the red line in Fig. 1b. We only focus on the even symmetry PhCW mode. After the optimization of the structural parameters with respect to the high group index for a large bandwidth, the lattice constant of 390 nm and the diameter of the holes of 193 nm are chosen, respectively, in our final design. The position of the first row of holes adjacent to the PhCW core is moved 41 nm outward from the original position, and the second row is moved 10 nm outward. Figure 1c displays the calculated (blue line) and measured (green dot) group indices as well as the measured transmission spectrum (red line) (see Supplementary Fig. 1 and Supplementary Note 1). Figure 1d shows a scanning electron microscope image of the fabricated silicon PhCW, where coupling regions are introduced between the strip waveguide and the slow-light PhCW to reduce the coupling loss46. The length of the fabricated PhCW is about 10 μm. As shown by the green curve, the fabricated silicon PhCW has a semi-slow-light region at approximately 1,540 nm with a group index of approximately 25; a larger group index can be obtained at longer wavelengths at the cost of larger insertion losses and pronounced fluctuations with wavelength, as shown in the grey area in Fig. 1c. The slight deviation from the theoretical calculation is attributed to the deviations in the fabrication procedure as well as the presence of the thin aluminium oxide layer deposited on the silicon that leads to the tiny shift of the group index curve from the ideal curve to the curve with the longer wavelength range. The trade-off for the slow-light enhancement is a reduced spectral operation bandwidth, which is optimized to approximately 10 nm in our design. Figure 1e shows the temperature response for different heating power, and Fig. 1f illustrates the temperature distribution of a graphene–PhCW structure. The thermal field is tightly localized in the central area of the PhCW, thus ensuring an efficient heating. Besides, the theoretical response time of the proposed microheater is about 420 ns, which is faster than most previous reported microheaters.
Device fabrication and characterization
To characterize the performance of the graphene microheater, we fabricated a tunable MZI filter on a silicon-on-isolator wafer with a 250-nm-thick top silicon layer and a 2 μm SiO2 buried oxide (BOX) layer (see detailed fabrication process in Supplementary Fig. 2 and Supplementary Note 2), as shown in Fig. 2a,b. The transverse electric (TE)-polarized light is coupled from a fibre to the waveguide using a photonic crystal grating coupler47. The experimental setup is described in detail in Supplementary Fig. 3 and Supplementary Note 3. A multi-mode interferometer divides the input light equally into the two arms of the MZI, both consisting of silicon strip waveguides with dimensions of 450 nm × 250 nm and 28-μm-long PhCW, which includes the slow light region and two coupling regions. The length of graphene–PhCW covering the slow-light waveguide is 20 μm. Raman spectroscopy is employed to examine the quality of graphene after the wet-transfer process, as shown in Supplementary Fig. 5 and Supplementary Note 5, indicating good wet-transfer quality with minor defects. One of the strip waveguides is designed to be 145.7 μm longer than the other in order to induce an appropriate optical path difference. Moreover, to balance the loss induced by the presence of graphene, the PhCW in both arms have equal lengths of graphene on top. Based on the resonant condition of the MZI, we can obtain the resonance shift Δλ versus the phase shift as , where λ0 is the resonance wavelength before heating and ΔL is the length difference between the two arms of the MZI. In combination with equation (1), we anticipate that the larger group index can induce larger resonance shift.
The transmission spectrum (blue line) of the fabricated MZI without the graphene heater is depicted in Fig. 2c. In our analyses, the measured optical power output is normalized to the reference strip waveguide to exclude the coupling loss of the grating couplers. According to Fig. 2d, the interference dip at 1533.71 nm lies in the slow-light region. Although accompanying lobes and multiple dips, the interference dip can be approximately determined by fitting the measured data with sine functions. The measured free spectral range (FSR) is approximately 4 nm. For comparison, the transmission spectrum of the device incorporating the graphene heater is measured as well, which is shown in the red curve in Fig. 2c. An excess loss of 5 dB is induced, and the extinction ratio is degraded to approximately 8 dB in the MZI with graphene. Except for the loss of 1.1 dB induced by graphene, the excess loss is mainly attributed to metallic contamination during the wet-transfer and lift-off process48. Such degradations can be optimized by improving the wet-transfer process by using a modified Radio Corporation of America (RCA) clean process49.
Next, an external voltage is applied to the graphene heater, and the spectral responses are measured for different applied powers (see experimental setup in Supplementary Fig. 3 and Supplementary Note 3); the results are presented in Fig. 2d. The shift of the interference dip at approximately 1533.71 nm reaches one FSR (from the solid blue line to the solid red line) with a tuning power of only 3.99 mW. Meanwhile, there is a larger shift of the interference dip at 1533.71 nm than that for the dip at 1525.12 nm, which agrees well with the theoretical prediction of equation (1), i.e., larger group index (at a longer wavelength) enables higher heating efficiency. Figure 2e plots the shifts of the interference dips at 1533.71 nm (red line) and 1525.12 nm (blue line) as functions of the tuning power, and tuning efficiencies (η) of 1.07 and 0.65 nm mW−1 are achieved, respectively.
The response time of the graphene heater is further characterized by driving the graphene heater with a square waveform electrical signal while the wavelength of the input signal is fixed at 1531.8 nm. The frequency of the driving signal is set to 100 kHz, and the peak-to-peak voltage (Vpp) is set to 7 V, as shown in Fig. 2f. The Vpp of 7 V corresponds to an applied heating power of 3.27 mW. The modulated light is received by a photodetector and recorded by an oscilloscope; the results are shown in Fig. 2g. The 10–90% rising and decaying times are measured to be 750 and 525 ns, respectively. To the best of our knowledge, this is the fastest response time reported for a microheater in silicon photonics. The fast response time is attributed to the silicon photonic crystal membrane with high thermal conductivity of silicon. The figure of merit, i.e., the product of the power consumption per FSR and the average response time50, can be used for a comprehensive evaluation of the microheater performance. Our slow-light-enhanced graphene heater has a figure of merit as good as 2.543 nW s, which is one order of magnitude better than previous demonstrations50.
The influence of the graphene–PhCW interaction length
To investigate the impact of the graphene–PhCW interaction length on the tuning efficiency of the heater, we fabricated and measured the MZI with graphene–PhCW overlap lengths of ∼5 and ∼3 μm, shown as in Fig. 3a,b. The measured transmission spectra at different heating powers for graphene–PhCW overlap lengths of ∼5 and ∼3 μm are shown in Fig. 3c,d, respectively, and the corresponding shifts of the transmission spectrum dips as functions of the heating power are depicted in Fig. 3e,f. The resonance shifts are measured at 1532.5 and 1539.2 nm for the case of 5 and 3 μm, respectively. The tuning efficiency decreases when having a shorter graphene–PhCW overlap length, which is in accordance with equation (1) and the thermal distribution mentioned in Supplementary Fig. 4 and Supplementary Note 4. Besides, the interference dips at the shorter wavelength also experience smaller shift under the same heating power, therefore confirming the enhancement due to slow light in both cases.
The influence of the shape of the graphene microheater
The shape of the graphene heater can have a significant influence on the tuning efficiency. According to our calculated temperature distribution for different shapes of the graphene heater, the tuning efficiency for the narrow-width long-length graphene heater is the highest. The details of the theoretical analysis can be found in Supplementary Fig. 4 and Supplementary Note 4. As shown in Fig. 2b, in the previous design, the graphene coverage on the photonic crystal is designed to be Z-shaped to boost the tuning efficiency. For comparison, a straight-shaped graphene heater fully covering the PhCW membrane is fabricated, as shown in Fig. 4a. Figure 4b shows the voltage–current relationships of both the straight-shaped (red line) and Z-shaped (blue line) graphene layers. The total resistance of the straight-shaped heater is 1.42 kΩ, which is more than 10 times lower than that of the Z-shaped heater. According to the data in Fig. 4c, the heating efficiency is only 0.14 nm mW−1 for the straight-shaped heater, much lower than that for the Z-shaped heater. This is because in the Z-shaped case, heat is predominantly generated in the region overlapping the photonic crystal membrane where the light is mainly confined. Thus, the heating-induced modulation of the waveguide can be much more efficient. In contrast, in the straight-shaped case, heat is generated uniformly throughout the entire graphene layer, and only a very small part of the heater effectively overlaps the optical mode; hence, the tuning efficiency is relatively modest, which agrees well with our analytical results. We also test the dynamic response of the device with the straight-shaped heater using the same square waveform electrical signal shown in Fig. 4d and the modulated signal shown in Fig. 4e. Here, we find the rise and decay times to be 850 and 875 ns, respectively. The slower rising time is due to the low heating efficiency, and the slower decay time may be because more overall heat is generated with the same external voltage, requiring more time for dissipation of the heat through the silicon membrane.
Discussion
In conclusion, we have experimentally demonstrated slow-light-enhanced energy-efficient graphene microheaters with ultrafast response times. We have comprehensively studied the influences of the graphene–PhCW interaction length and the shape of the graphene heater to the heat efficiency. Owing to the slow-light effect, the heating efficiency is as high as 1.04 nm mW−1, and the power consumption is as low as 3.99 mW. Furthermore, the 10–90% rising and decaying times are measured to be only 750 and 525 ns, which are the fastest ever reported for microheaters in silicon photonics. To the best of our knowledge, the figure of merit of the proposed device is lower than all previously demonstrated filters based on microheaters. Owing to the widely required applications of microheaters in the photonic integrated circuits, the proposed concept of combining graphene microheater with PhCW provides a promising solution to reduce power consumption in many functional photonic devices, such as optical phase-array antenna, on-chip arbitrary waveform generators, optical switches, phase shifters, tunable filters and modulators. It should be noted that as one of the main challenges in its future application, the relatively high insertion loss could be greatly improved by optimizing the fabrication process to eliminate the metallic contamination during the wet-transfer process51,52. Besides, although employing longer PhCW–graphene interaction length may further reduce power consumption, the uniformity in the fabrication of long PhCW should also be considered as another potential challenge as well as the degradation of the graphene microheater. The CMOS-compatible fabrication process of the proposed device enables its wafer-level integration with other nanophotonic devices. The slow-light-enhanced energy-efficient graphene microheater has demonstrated its distinctive advantages in simultaneously achieving both a low power consumption and a fast response time, showing great potential for its use in configurable photonic integrated circuits.
Methods
Device fabrication
The proposed tunable MZI filter was fabricated on an silicon-on-isolator wafer with a 250-nm-thick silicon layer on top of a 2 μm SiO2 buried layer. E-beam lithography and inductively coupled plasma etching were used to fabricate the grating couplers, strip waveguides, multi-mode interferometer and the PhCWs. Standard ultraviolet (UV) lithography was performed to define the wet etch regions used to undercut the PhCWs with AZ5124E acting as the mask. Buffered hydrofluoric acid was used to etch the SiO2 buried layer below the PhCWs. After the membranization, an 11 nm aluminium oxide layer was deposited on the device by atomic-layer deposition. A graphene sheet grown by CVD was wet-transferred onto the silicon device. In the wet-transfer process, AZ resist was first spin-coated onto the graphene covered copper foil and dried at 100 °C for 1 min. Next, an AZ/graphene membrane was obtained by etching away the copper foil in an Fe(NO3)3/H2O solution and then transferring onto the silicon chip. Then, the AZ resist was dissolved in acetone, simultaneously cleaning the graphene surface. The graphene shape was defined using standard UV lithography and O2 plasma etching. Finally, Au/Ti contacts were fabricated on the graphene by standard UV lithography, followed by metal deposition and a lift-off process.
Data availability
The data that support the findings of this study are available from the corresponding authors upon request.
Additional information
How to cite this article: Yan, S. et al. Slow-light-enhanced energy efficiency for graphene microheaters on silicon photonic crystal waveguides. Nat. Commun. 8, 14411 doi: 10.1038/ncomms14411 (2017).
Publisher’s note: Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
References
Schulz, G. The Green and Virtual Data Center CRC Press (2016).
Asghari, M. & Krishnamoorthy, A. V. Silicon photonics: energy-efficient communication. Nat. Photon. 5, 268–270 (2011).
Soref, R. The past, present, and future of silicon photonics. IEEE J. Sel. Top. Quant. Electron 12, 1678–1687 (2006).
Hochberg, M. & Baehr-Jones, T. Towards fabless silicon photonics. Nat. Photon. 4, 492–494 (2010).
Leuthold, J., Koos, C. & Freude, W. Nonlinear silicon photonics. Nat. Photon. 4, 535–544 (2010).
Timurdogan, E. et al. An ultralow power athermal silicon modulator. Nat. Commun. 5, 4008 (2014).
Reed, G. T., Mashanovich, G., Gardes, F. & Thomson, D. Silicon optical modulators. Nat. Photon. 4, 518–526 (2010).
Casalino, M., Iodice, M., Sirleto, L., Rendina, I. & Coppola, G. Asymmetric MSM sub-bandgap all-silicon photodetector with low dark current. Opt. Express 21, 28072–28082 (2013).
Mueller, T., Xia, F. & Avouris, P. Graphene photodetectors for high-speed optical communications. Nat. Photon. 4, 297–301 (2010).
Goykhman, I., Desiatov, B., Khurgin, J., Shappir, J. & Levy, U. Locally oxidized silicon surface-plasmon Schottky detector for telecom regime. Nano Lett. 11, 2219–2224 (2011).
Rosa, Á., Gutiérrez, A., Brimont, A., Griol, A. & Sanchis, P. High performace silicon 2 × 2 optical switch based on a thermo-optically tunable multimode interference coupler and efficient electrodes. Opt. Express 24, 191–198 (2016).
Jalali, B. & Fathpour, S. Silicon photonics. J. Lightwave Technol. 24, 4600–4615 (2006).
Reed, G. T. & Knights, A. P. Silicon Photonics: an Introduction John Wiley & Sons (2004).
Espinola, R., Tsai, M., Yardley, J. T. & Osgood, R. Jr Fast and low-power thermooptic switch on thin silicon-on-insulator. IEEE Photon Technol. Lett 15, 1366–1368 (2003).
Sherwood-Droz, N. et al. Optical 4 × 4 hitless silicon router for optical networks-on-chip (NoC). Opt. Express 16, 15915–15922 (2008).
Gu, L., Jiang, W., Chen, X. & Chen, R. T. Thermooptically tuned photonic crystal waveguide silicon-on-insulator Mach-Zehnder interferometers. IEEE Photon Technol. Lett 19, 342 (2007).
Yamane, T., Nagai, N., Katayama, S.-I. & Todoki, M. Measurement of thermal conductivity of silicon dioxide thin films using a 3omega method. J. Appl. Phys. 91, 9772–9776 (2002).
Dong, P. et al. Thermally tunable silicon racetrack resonators with ultralow tuning power. Opt. Express 18, 20298–20304 (2010).
Sun, P. & Reano, R. M. Submilliwatt thermo-optic switches using free-standing silicon-on-insulator strip waveguides. Opt. Express 18, 8406–8411 (2010).
Li, X. et al. Fast and efficient silicon thermo-optic switching based on reverse breakdown of pn junction. Opt. Lett. 39, 751–753 (2014).
Baba, T. Slow light in photonic crystals. Nat. Photon. 2, 465–473 (2008).
Krauss, T. F. Why do we need slow light? Nat. Photon. 2, 448–450 (2008).
Vlasov, Y. A., O’Boyle, M., Hamann, H. F. & McNab, S. J. Active control of slow light on a chip with photonic crystal waveguides. Nature 438, 65–69 (2005).
Mortensen, N. A. & Xiao, S. Slow-light enhancement of Beer-Lambert-Bouguer absorption. Appl. Phys. Lett. 90, 141108 (2007).
Ek, S. et al. Slow-light-enhanced gain in active photonic crystal waveguides. Nat. Commun. 5, 5039 (2014).
Corcoran, B. et al. Green light emission in silicon through slow-light enhanced third-harmonic generation in photonic-crystal waveguides. Nat. Photon. 3, 206–210 (2009).
Geim, A. K. & Novoselov, K. S. The rise of graphene. Nat. Mater. 6, 183–191 (2007).
Novoselov, K. S. et al. Electric field effect in atomically thin carbon films. Science 306, 666–669 (2004).
Bolotin, K. I. et al. Ultrahigh electron mobility in suspended graphene. Solid State Commun. 146, 351–355 (2008).
Du, X., Skachko, I., Barker, A. & Andrei, E. Y. Approaching ballistic transport in suspended graphene. Nat. Nanotechnol. 3, 491–495 (2008).
Bao, Q. et al. Broadband graphene polarizer. Nat. Photon. 5, 411–415 (2011).
Zhu, X. et al. Enhanced light-matter interactions in graphene-covered gold nanovoid arrays. Nano Lett. 13, 4690–4696 (2013).
Gu, T. et al. Photonic and plasmonic guided modes in graphene–silicon photonic crystals. ACS Photonics 2, 1552–1558 (2015).
Gu, T. et al. Regenerative oscillation and four-wave mixing in graphene optoelectronics. Nat. Photon. 6, 554–559 (2012).
Ding, Y. et al. Effective electro-optical modulation with high extinction ratio by a graphene–silicon microring resonator. Nano Lett. 15, 4393–4400 (2015).
Kang, J. et al. High-performance graphene-based transparent flexible heaters. Nano Lett. 11, 5154–5158 (2011).
Gan, S. et al. A highly efficient thermo-optic microring modulator assisted by graphene. Nanoscale 7, 20249–20255 (2015).
Yu, L., Yin, Y., Shi, Y., Dai, D. & He, S. Thermally tunable silicon photonic microdisk resonator with transparent graphene nanoheaters. Optica 3, 159–166 (2016).
Bao, Q. & Loh, K. P. Graphene photonics, plasmonics, and broadband optoelectronic devices. ACS Nano 6, 3677–3694 (2012).
Watanabe, E., Conwill, A., Tsuya, D. & Koide, Y. Low contact resistance metals for graphene based devices. Diamond Relat. Mater. 24, 171–174 (2012).
Mortensen, N. A., Xiao, S. & Pedersen, J. Liquid-infiltrated photonic crystals: enhanced light-matter interactions for lab-on-a-chip applications. Microfluid. Nanofluidics 4, 117–127 (2008).
Pedersen, J. G., Xiao, S. & Mortensen, N. A. Limits of slow light in photonic crystals. Phys. Rev. B 78, 153101 (2008).
Frandsen, L. H., Lavrinenko, A. V., Fage-Pedersen, J. & Borel, P. I. Photonic crystal waveguides with semi-slow light and tailored dispersion properties. Opt. Express 14, 9444–9450 (2006).
Li, J., White, T. P., O’Faolain, L., Gomez-Iglesias, A. & Krauss, T. F. Systematic design of flat band slow light in photonic crystal waveguides. Opt. Express 16, 6227–6232 (2008).
Johnson, S. G. & Joannopoulos, J. D. Block-iterative frequency-domain methods for Maxwell’s equations in a planewave basis. Opt. Express 8, 173–190 (2001).
Hugonin, J. P., Lalanne, P., White, T. P. & Krauss, T. F. Coupling into slow-mode photonic crystal waveguides. Opt. Lett. 32, 2638–2640 (2007).
Ding, Y., Ou, H. & Peucheret, C. Ultrahigh-efficiency apodized grating coupler using fully etched photonic crystals. Opt. Lett. 38, 2732–2734 (2013).
Kang, J., Shin, D., Bae, S. & Hong, B. H. Graphene transfer: key for applications. Nanoscale 4, 5527–5537 (2012).
Liang, X. et al. Toward clean and crackless transfer of graphene. ACS Nano 5, 9144–9153 (2011).
Schall, D. et al. Infrared transparent graphene heater for silicon photonic integrated circuits. Opt. Express 24, 7871–7878 (2016).
Mohsin, M. et al. Graphene based low insertion loss electro-absorption modulator on SOI waveguide. Opt. Express 22, 15292–15297 (2014).
Liu, M., Yin, X. & Zhang, X. Double-layer graphene optical modulator. Nano Lett. 12, 1482–1485 (2012).
Acknowledgements
This work is supported by the Danish Council for Independent Research (DFF-1337−00152 and DFF-1335-00771) and the National Natural Science Foundation of China (Grant No. 61622502 and 61475052). The Center for Nanostructured Graphene is sponsored by the Danish National Research Foundation, Project DNRF103. S.Y. is sponsored by the China Scholarship Council (CSC) for supporting his work in Denmark.
Author information
Authors and Affiliations
Contributions
S.Y. and Y.D. proposed the slow-light-enhanced tunable silicon MZI with a graphene heater. S.Y., L.H.F. and S.X. performed numerical simulations. S.Y., Y.D. and X.Z. fabricated the graphene−silicon hybrid tunable MZI device. S.Y. and Y.D. performed the measurements. S.Y., Y.D., S.X. and J.D. discussed and analysed the measured data. S.Y. wrote the first draft of the manuscript. All the authors discussed the results and contributed to the writing of the manuscript.
Corresponding authors
Ethics declarations
Competing interests
The authors declare no competing financial interests.
Supplementary information
Supplementary Information
Supplementary Figures and Supplementary Notes (PDF 757 kb)
Rights and permissions
This work is licensed under a Creative Commons Attribution 4.0 International License. The images or other third party material in this article are included in the article’s Creative Commons license, unless indicated otherwise in the credit line; if the material is not included under the Creative Commons license, users will need to obtain permission from the license holder to reproduce the material. To view a copy of this license, visit http://creativecommons.org/licenses/by/4.0/
About this article
Cite this article
Yan, S., Zhu, X., Frandsen, L. et al. Slow-light-enhanced energy efficiency for graphene microheaters on silicon photonic crystal waveguides. Nat Commun 8, 14411 (2017). https://doi.org/10.1038/ncomms14411
Received:
Accepted:
Published:
DOI: https://doi.org/10.1038/ncomms14411
This article is cited by
-
Two-dimensional materials for future information technology: status and prospects
Science China Information Sciences (2024)
-
Graphene-integrated waveguides: Properties, preparation, and applications
Nano Research (2022)
-
MIR optical modulator based on silicon-on-calcium fluoride platform with VO2 material
Optical and Quantum Electronics (2021)
-
Graphene-based all-optical modulators
Frontiers of Optoelectronics (2020)
-
Performance of integrated optical switches based on 2D materials and beyond
Frontiers of Optoelectronics (2020)
Comments
By submitting a comment you agree to abide by our Terms and Community Guidelines. If you find something abusive or that does not comply with our terms or guidelines please flag it as inappropriate.